Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: boxlad on June 07, 2010, 05:16:02 PM

Title: Removing old bellows tape
Post by: boxlad on June 07, 2010, 05:16:02 PM
What is the best way to remove old bellows tape without damaging the bellows? Some of it comes off easily but some is stuck on and I don't want to force it too much. The plan is to re-tape the bellows.. Any suggestions or tips???
Title: Re: Removing old bellows tape
Post by: Theo on June 07, 2010, 05:28:18 PM
Peel of as much as possible first then spray the tape with plain water, leave covered for a while until the glue softens then peel/scrape off the remaining tape.  Its a very messy job!  It may help the water to soak in if you use coarse abrasive paper to take the surface of the tape first.
Title: Re: Removing old bellows tape
Post by: Bill the Farmer on June 07, 2010, 05:56:23 PM
I found it surprisingly easy to get the tape off of my pokerwork. I just slid a blunt knife under it, most of it came off in one piece.
Title: Re: Removing old bellows tape
Post by: theSmoiler on June 09, 2010, 12:25:43 AM
It may depend on what type of bellows tape you're dealing with eg simple paper, or 'fabricised' type, or those with even more of a 'plasticy' finish such as the Hohner-type ribbed tape. I've just been doing some more work on the bellows of one of my old Modell I Hohners: the tape was simple orange-coloured paper - some of which the top, coloured layer peeled off easily; some didn't - and the bottom layer was almost invariably left very well stuck on. So, I simply sanded this down with fine sandpaper - making sure to deftly 'flick' away the debris immediately, using a shaving brush, so as not to risk it staining the cream bellows card - then stuck the new tape over the top (the original bits I did when I first started work on this box have remained very well stuck for at least 5 years). Because you can still generally see the outline of the original tape, it makes it easier to line up the new tape correctly along the bellows.

Diane
Title: Re: Removing old bellows tape
Post by: Christopher K. on June 09, 2010, 01:28:28 AM
It may depend on what type of bellows tape you're dealing with eg simple paper, or 'fabricised' type, or those with even more of a 'plasticy' finish such as the Hohner-type ribbed tape. I've just been doing some more work on the bellows of one of my old Modell I Hohners: the tape was simple orange-coloured paper - some of which the top, coloured layer peeled off easily; some didn't - and the bottom layer was almost invariably left very well stuck on. So, I simply sanded this down with fine sandpaper - making sure to deftly 'flick' away the debris immediately, using a shaving brush, so as not to risk it staining the cream bellows card - then stuck the new tape over the top (the original bits I did when I first started work on this box have remained very well stuck for at least 5 years). Because you can still generally see the outline of the original tape, it makes it easier to line up the new tape correctly along the bellows.

Diane

Ditto on the different kinds of tape/old and dry tape. I recently removed 'tape' from the bellows of an old Koch purchased on eBay. Although the bellows were shot - very brittle and with holes in the corners - the reeds and casework look untouched. The tape was made of thick textured paper and glue. Wanting to salvage the card and bellows frames, I tore and scraped carefully at all the tape on the tops of the folds and carefully sanded off the rest. Thinking back on it, spraying water to loosen the glue would have been a good idea. 
Title: Re: Removing old bellows tape
Post by: theSmoiler on June 09, 2010, 10:13:37 PM
I recently removed 'tape' from the bellows of an old Koch purchased on eBay. Although the bellows were shot - very brittle and with holes in the corners - the reeds and casework look untouched. The tape was made of thick textured paper and glue. Wanting to salvage the card and bellows frames, I tore and scraped carefully at all the tape on the tops of the folds and carefully sanded off the rest. Thinking back on it, spraying water to loosen the glue would have been a good idea.  

I don't necessarily agree with the water idea: the bellows I have been working on are exactly the same ie orange tape and edging, as on the Koch I also have - so likely the same as the one's you're describing. When I was sanding I was sat outside and it just started to rain - where the water caught the tape debris in one place, orange stain was produced. Therefore, water may not be appropriate for this purely paper tape - as opposed to the fabricised/ plasticised variety - as may cause significant colour run.
Title: Re: Removing old bellows tape
Post by: diatonix on June 10, 2010, 12:26:37 AM
I must admit that I have used water myself to moisten stubborn tape, but I don't recommend it, as it may easily weaken the cardboard underneath, while not making the job itself much easier. If the tape to be removed is made of paper (e.g. Hohner Erica) I sometimes just get rid of the bits covering the metal corners. The paper is so thin that you can simply cover it with new kaliko and get away with it. You might consider sanding it slightly before doing so, as the glue will stick better. Carini provides a variety of kaliko that is slightly  wider than normal ("dermoide per riparazione"), which makes it easy to cover anything you don't want to be visible. Quite often I cut my own tape from something known as granitol (looks a lot better on Ericas and older instruments in general rather than the shiny Italian "dermoide rigata"), bookbinders  are usually well stocked with it and it comes in most colours.
In the old days animal hide glue was commonly used for bellow tape, in that case a hair drier might be helpful (if used respectfully!) should you insist on removing all of the original kaliko.
Title: Re: Removing old bellows tape
Post by: theSmoiler on June 10, 2010, 01:04:33 AM
Quite often I cut my own tape from something known as granitol (looks a lot better on Ericas and older instruments in general rather than the shiny Italian "dermoide rigata"), bookbinders  are usually well stocked with it and it comes in most colours.

Yes, I've been cutting some of my own tape, too (alternating it with some Hohner ribbed tape, to try and give a look a bit like on the one-row bellows), from some book-binding stuff I got from a print shop ie 3/4" off 1" wide tape - easy to work with, much less messy, as pre-sticky, than tape and glue. I'm hoping I might be able to get some wider eg 1 1/2", to appropriately cover the old-style bellows ends on a Modell I. Currently have some in red and black - maybe I'll even be able to get some orange somewhere.... (:)
Title: Re: Removing old bellows tape
Post by: Theo on June 10, 2010, 08:29:04 AM
Yes, I've been cutting some of my own tape, too ...... Currently have some in red and black - maybe I'll even be able to get some orange somewhere.... (:)


The bookbinding material that Diatonix knows as 'granitol'   I think must be the same material that is known as buckram in the UK.  This is available in a large range of colours for example http://www.nolanwatts.co.uk/buckram%20colours.html (http://www.nolanwatts.co.uk/buckram%20colours.html)
Title: Re: Removing old bellows tape
Post by: diatonix on June 10, 2010, 10:11:59 AM
Thanks, Theo. No wonder I'm having a hard time finding something useful on "granitol" on the internet...
Title: Re: Removing old bellows tape
Post by: Theo on June 10, 2010, 10:22:08 AM
Haha!   Buckram is good stuff, though I would dearly like to find something even closer to the cloth tape used on 1930s Hohners. 

Something else to bear in mind is that new tape, or buckram is usually thicker than the old tape so after a full re-tape the bellows straps may be too short, particularly if you put new tape on top of old.
Title: Re: Removing old bellows tape
Post by: diatonix on June 10, 2010, 10:48:12 AM
The "granitol" I'm using is actually thinner than most types of modern kaliko. It may be the kind of tape/cloth you have been looking for, Theo, as it is almost identical to the one used on many older boxes.   
Title: Re: Removing old bellows tape
Post by: Theo on June 10, 2010, 11:21:40 AM
So where does it come from?  Who makes or sells it?
Title: Re: Removing old bellows tape
Post by: diatonix on June 10, 2010, 11:54:56 AM
I buy mine from a local book binder, who gets it from Denmark. He is a bit secretive about it, but I'll try and find out more.
Title: Re: Removing old bellows tape
Post by: HallelujahAl on June 10, 2010, 12:36:29 PM

Quote
Haha!   Buckram is good stuff, though I would dearly like to find something even closer to the cloth tape used on 1930s Hohners.


These are the folk I get a lot of my supplies from - buckram too - though I find the 'Arrestox B' a very good product. I also buy my rolls of adhesive linen supplies for hinging concertina bellows etc from them. Cloth tapes etc all available. I'm afraid the best place to go for any cotton based product is the States (they built an Empire out of the stuff! ) :D
http://talasonline.com/ (http://talasonline.com/)

Hope this helps?
AL
Title: Re: Removing old bellows tape
Post by: malcolmbebb on January 08, 2011, 04:58:31 PM
Haha!   Buckram is good stuff, though I would dearly like to find something even closer to the cloth tape used on 1930s Hohners. 

How does buckram stand up to flexing? The modern stuff seems to have a high acrylic content, is that an improvement or otherwise?
Title: Re: Removing old bellows tape
Post by: Christopher K. on January 09, 2011, 07:32:14 AM
Haha!   Buckram is good stuff, though I would dearly like to find something even closer to the cloth tape used on 1930s Hohners. 

How does buckram stand up to flexing? The modern stuff seems to have a high acrylic content, is that an improvement or otherwise?


I work 20 hours per week as a librarian's assistant, in addition to the 40 hours I put in at my "real" job as a cataloger and technician for a company which specializes in data migration, cataloging and physical processing of books and other materials for libraries and publishers. I'm elbows deep in buckram, most days.

Buckram is specifically intended to be strong and flexible for a very long time. I have seen editions bound in buckram which have seen decades of service and hundreds of circulations. A library rebinds a book and the buckram binding will usually last longer than the pages, unless the book was constructed with alkaline paper. The stuff with acrylic is used chiefly in bookbinding applications. You can still purchase buckram intended for clothing construction which has a lower or absent acrylic content.

Come to think of it (pure speculation here) it would not surprise me if Hohner were using a form of buckram for bellows construction in the old days because a bellows are not unlike a book. It would have been cheap and widely available. Why spend the time and money developing anything else?
Title: Re: Removing old bellows tape
Post by: malcolmbebb on January 09, 2011, 09:23:45 AM
because a bellows are not unlike a book.
There has to be a bad joke about reading music in here, but perhaps I'll let it go...

Thanks for the reply. I was thinking of using buckram to cover and re-tape a bellows, in this instance of a cheap concertina. In the meanwhile I was also thinking of building a bellows for a tuning rig and it seemed feasible to use buckram for that, too.
Although I did wonder about duct tape for the tuning rig...
SimplePortal 2.3.5 © 2008-2012, SimplePortal