Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Broadland Boy on July 13, 2010, 07:07:53 PM
-
Set up to make some reed wax this afternoon,
60g resin powder, 60g beeswax, 5ml olive oil
Heated the wax in a glass jar stood in a sucepan of boiling water (with a nice little ali takeway tray shroud to keep in the heat)
When melted, drizzled in the resin powder a spoonful at a time while stirring to avoid chilling the 'brew'
when all submerged, shot in the oil.
Heated, stirred, heated, stirred, stirred, stirred (ditto repeato for 3 hours)
when my patience finally ran out I had a thick gooey lump in the nice runny wax which felt like that pulled toffee and seemed to be getting stiffer (as I expect when making turners cement which this will be used for) and a mildly discoloured wax - with the resinous element extracted and cooled it looks like one of those dried figs or as Kim observed when she finally got into the kitchen to start tonights meal, some sort of animal dropping ::)
Any idea whats gone wrong ??
First thought was I should have left the oil until last (have I made some sort of polymer ??)
Second thought, had my heat retaining shroud dropped condensate from the water into the brew
Final thought, do people usually start with powdered or lump resin ?
Unless advised otherwise I shall try again by stirring lumps of resin into the hot wax!
Academic at present but what method of casting sticks is common ? I had corrugated some cooking foil with a view to pouring wax in the vees as I do when casting solder or turning wax - any other bright ideas ?
Note to Theo, if I had put some propolis in the mix I might have expected this, the jar of propolis on hand to add when the proper mix is poured satisfactorily so you may yet still be able to try some out........
Richard
-
60g resin powder, 60g beeswax, 5ml olive oil
Unless advised otherwise I shall try again by stirring lumps of resin into the hot wax!
Academic at present but what method of casting sticks is common ? I had corrugated some cooking foil with a view to pouring wax in the vees as I do when casting solder or turning wax - any other bright ideas ?
Think personally that this is too much rosin.
Melt the rosin first - then add the wax.
Best way I have found to make sticks - Pour some molten wax onto a tray of hot water - when cool you have a sheet of wax. Score it - chill it - snap it into sticks.
-
I've mafecthe occasional bowl of gloop too. It seems to be less of a problem if you add the oil after the wax and rosin have melted together.
To make sticks I pour the wax into a flat container the slice with a sharp knife and straight edge. The temperature has to be just right for this, too cold and the wax is brittle and cracks as you cut, too warm and the cut heals after the knife has passed. A warm room temp seems to work so I'd guess about 20 to 25 C.
-
Thanks both,
I had seen several ratios of rosin to wax in the old forum postings and since Theo and Rees of this parish indicate 50:50 is a good mix thats what I used, although I hadn't seen anything regarding which to melt into which, I had assumed the rosin would melt into the wax more easily than the reverse - Wrong !
Having tried to cut thicker wax cleanly before I hadn't considered cutting a thin sheet warm or casting it on a hot water bath and cooling, I was thinking of casting the finished sticks like you would cast your own foundation and I can see other applications for this (:)
No progress on the old Hohner today - I had mistakenly thought at least some of the reeds would be fitted tonight and I've a visit to the hospital tomorow so probably Thursday before I get round to another meltdown session.
Will advise progress - or lack of >:E
-
Interesting thread. Experimenting with resin recipes looks like loads of fun. There's also pre-mixed/oiled/formed Hohner reedplate wax available here:
https://www.shopssl.de/epages/es117831.sf/en_US/?ObjectPath=/Shops/es117831_stringsandboxes/Categories/%22Akkordeon%20Werkstoffe%22/Stimmplattenwachs
I'd be interested in making my own to compare the results with some "prefab" wax that is supposed to work as it should.
(The link is to an English translation of the page, and the original German page is here: https://www.shopssl.de/epages/es117831.sf/)
-
Does pine rosin have a higher melting point than wax, and if so, shouldn't it be melted first?
-
Thanks for that, Charlie Marshall supplies an equivalent in the UK (as no doubt to several others)
The lignite resin, turpentine and other additives is an interesting departure from the mixes in the old forum threads.
Yes the resin does melt at a higher temp than beeswax
Having used a very fine resin powder, sifted from the lumps, the liquid poured off into a mould weighs 88g (original wax 60g) the resultant resin 'dried fig' is 25 which assuming no evaporation leaves 7g stuck in the bottom of the jar (with just under 5g of oil somewhere between the two) so obviously some resin has amalgamated with the wax.
I suspect people may start from a more granular resin or just plain lumps which means it does not gloop in a lump with relatively low surface area. While not specified in the recipes, the implication is that both are melted together and then after serious stirring finally amalgamate
Having got the 'why did it do that' bit between me teeth I shall try both resin powder first to melt and wax / lump resin together - My adding oil before all was fully mixed may well have had a negative effect - will report results as and when available.
As for lignite resin - well it'll have to go without !
Richard
-
Well, after some wax wangling experiments today I can report that wax first or (lump) resin first ends up with the same result, although with some liquid wax the resin seems to combine more easily - my first disastrous attempt would appear to be as a result of adding the oil before all the resin was combined with the wax and perhaps that it was powdered resin encouraged this to happen.
Olive or Linseed oils also appear to make no noticeable difference to the finished product, have yet to trial it.
Adding some propolis (5g to a 200g batch) resulted in another gooey blob which would not dissolve, with so little to start with and some wax left on the jar (which I neglected to weigh before starting) I cannot determine how much actually went into the final product but it is darker than the other 'brews' and noticeably more tacky at hand hot temperature.
Still trying to track down a CSR1504B or equivalent mains power regulator at a reasonable price so I can set my soldering / pyrography iron at an appropriate temperature to re set me reedplates, corners of bellows leathers to have a drop of neatsfoot oil to soften them and hopefully i'm not to far from having a tune out of the box, however untuned it may be....
Oh and invested 6 quid in a bottle of nickel plating solution for the 'furniture' - anyone had any experience of 'pen plating' with Nickel ?
Richard
-
Still trying to track down a CSR1504B or equivalent mains power regulator at a reasonable price so I can set my soldering / pyrography iron at an appropriate temperature to re set me reedplates...
Richard
I've got a very old Weller fixed temperature iron which is far too hot for reed wax, so I made a bit extension out of copper wire which gets down to about the right temperature.
-
All this talk about which component to melt first reminded me of a "friend" who decided to deep fry some chicken. The chicken was excellent, but the contamination of the deep fry oil with chicken fat meant that it could never again achieve the heat required to cook chips! So I guess it does matter.
Rob.
-
Bill,
Posted on the 'Old Hohner' topic last night, I made up a chopper similar to a dimmer switch which while not temperature controlled, kept the iron (a small Antex) down at an ideal heat. Had some noise from the re assembled box but have a few reads not speaking properly, when I've sorted those, will point it at your tuner to see what else needs to be done.
Rob,
If I were melting metal, the lowest temperature would be the last into the pot, however, I feel that with this brew, melting the beeswax first and then drizzling the resin chunks in afterwards gave a quicker absorbtion than resin first due to its viscosity and tendancy to become a stick blob - probably due to the surface area available for melting, having tried a stick of both when refitting the reeds last night there is no perceptible difference between them in use and I guess if they last as long as the original wax which is/was in perfect order I'll be long gone before finding out how durable it is.......
Richard
-
I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and it worked like a charm. Cost me only $27 in a craft store.
-
I use a stylus for hot wax art, it is obviously calibrated to melt wax!
While my soldering iron isn't calibrated or temperature controlled in the thermostatic sense it is a miniature for fine soldering jobs with a thinned down bit end I use for signing the odd bit of woodturning (that is good enough to pass on) with my new power controller it is very docile to use on wax (:)
Forgot to mention previously, on speaking with a beekeeping friend regarding casting wax sheet over hot water for sticks, he suggested I pass on the information not to try putting wax, at any temperature, through a set of pasta rolls to get thin sheet or strips, it goes in OK but his experience of getting it out again was not good, very not good :'( :'(
On wax composition, the top three pairs of reeds in my old Hohner currently under repair, I have left in their original wax, where I have run the iron into it, the percentage of Rosin appears to be very high, nearer 100% than 50% would be my guess.
Richard
-
Interesting thread. Experimenting with resin recipes looks like loads of fun. There's also pre-mixed/oiled/formed Hohner reedplate wax available here:
https://www.shopssl.de/epages/es117831.sf/en_US/?ObjectPath=/Shops/es117831_stringsandboxes/Categories/%22Akkordeon%20Werkstoffe%22/Stimmplattenwachs
I'd be interested in making my own to compare the results with some "prefab" wax that is supposed to work as it should.
(The link is to an English translation of the page, and the original German page is here: https://www.shopssl.de/epages/es117831.sf/)
Nielsen told me that he uses carnauba wax as part of his own mixture, but wouldn't say what else was in it :-(
Ian
-
It is tempting to make your own wax recipe, but the trouble is you really need to be around for a couple of decades to see if it lasts as long as the tried and tested mixes.
I wonder what the Carnuba wax added to the plot? It is common ingredient of wax polishes because it is harder than beeswax and easier to buff to a high gloss. I believe that the blue/green coloured wax I've seen on some boxes is from Neilson. Its rather soft, and I suspect contains a proportion of paraffin wax which would give it a lower melting point, which is increasing the risk of dropped reeds if the box is left in a hot place.
-
It is tempting to make your own wax recipe, but the trouble is you really need to be around for a couple of decades to see if it lasts as long as the tried and tested mixes.
I wonder what the Carnuba wax added to the plot? It is common ingredient of wax polishes because it is harder than beeswax and easier to buff to a high gloss. I believe that the blue/green coloured wax I've seen on some boxes is from Neilson. Its rather soft, and I suspect contains a proportion of paraffin wax which would give it a lower melting point, which is increasing the risk of dropped reeds if the box is left in a hot place.
The green wax is Nielsen's, he does this so he can tell which reeds he's previously worked on. I've never had any of these reeds drop off at high temperatures.
If mixtures of reed waxes behave like mixtures of metals in alloys, maybe the hard carnauba wax adds high temperature strength and allows softer wax to be used as the main proportion to give better mechanical strength (resistance to fracture under shock/vibration) ?
Of course Nielsen's been around for rather more than a couple of decades, so I expect he knew what was doing with wax :-)
Ian
-
It's difficult to know what to believe of Nielsen's stories, but he told me he talked to industrial wax manufacturers and the result was that he developed a wax that had no plant based ingredients (based on mineral oil products, I suppose) which made it longer lasting. Natural waxes have ingredients that "go off" with time; his don't (or don't so much).
-
no plant based ingredients
Hmm, carnuba is a from plant origin, but beeswax is not! I wonder what he uses to replace the pine rosin?
To assert that plant based waxes "go off" in time and synthetic or mineral waxes don't seems rather a sweeping generalisation.
-
OK, don't quote me on the details. :|bl I do remember him saying:
(1) that "traditional" waxes made from natural ingredients based on living things were fine to start with but went wrong (usually going hard and brittle, I think) after years of use.
(2) That his approach resulted from talking to industrial wax makers/users and that his wax lasts longer.
Maybe he does use beeswax or wood resin, and it's some other ingredient that he's changed.
Needless to say, he wasn't too explicit about exactly what he used, and he's hard enough to understand at the best of times...
-
Is beeswax (technically) "Veggie" ? :|glug
In that it originates from the nectar collected from plants, some of which may be vegetables yes Chris, but bees secrete it from glands after ingesting either their nectars or the sugar solution we wicked bee keepers give them to make a comb with if they are from a swarm or colony division, or placate them with if we steal their hunny, so for purposes of Veganism it is an animal (insect) derived material, how this equates to drinking milk but not wearing leather I have no idea, or (unusually) opinion.....................
Anyhow as I understand from Prof Hawking* that all come from stardust anyway ;D
Some of the modern microcrystaline waxes are beginning to gain favour as protective coatings - Given the track record of the various grades of Ensis fluid and Waxoyl type of products there's plenty of past history for their durability and resistance to drying out and cracking but not so much on a timber substrate - if it were an issue then sealing the wood surface of the reedblock would reduce drying but I suspect that being able to penetrate the surface grain is part of the adhesive effect.
Having seen some trade 'offerings' of refined beeswax compared with mine, part of the processing bleaches the colour which reduces the propolis and pollen 'contamination' and it is no where near as sticky when melted, if you are making your own reed wax, get the wax from as close to the bee as you can - would you agree Theo ?
I have a lump of beeswax from my grandfather, who kept bees in the 1930's, he, my dad and now I use it for waxing thread for shoe / leather repairs, its surface is filthy but the wax is still fresh and when you draw a thread through it you can still smell the hive, unfortunately heating old reedwax the smell of the resin tends to dominate but I think you can still smell the wax, which means the volatiles are still intact to a large extent.
I like the idea of colour coding wax, like the minute watchmakers marks indicating their contribution to the history of a timepiece.
Richard
(who tried to run me over in his chariot in Cambridge one evening when I wasn't even carrying a melodeon)
-
I've just found another use for reedwax, champing down on a hard bit of pork rind tonight removed a filling, its settling nicely on its bed of reedwax and I've already got a dentist visit booked next week (:) :( ??? ???
Richard
-
I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and it worked like a charm. Cost me only $27 in a craft store.
That sounds like a good tip to me (:) I've been wondering what the best method might be.
-
I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and it worked like a charm. Cost me only $27 in a craft store.
That sounds like a good tip to me (:) I've been wondering what the best method might be.
Just now got around to reading this great thread. As for a soldering iron, I use a small pencil type that has a copper tip that was round. Following advise from the late Richard Morse, I hammered the soft copper tip into a bit of a curved flat blade. (More surface area, fits into many diverse places). Since the heat level of the iron is fixed, I made a regulator by using an ordinary incandescent lighting dimmer. This is installed (along with a power receptacle) in an electrical box with an extension cord. The dimmer provides perfect control for the iron.
I have read many cautionary tales about overheating the wax. I have the 'dimmer' set to heat the iron to the point where the wax will slightly smoke if not constantly fed new wax. Using the wax in stick form allows you to operate just as if you are 'soldering' the reeds in place and gives great control. If you need more or less heat, you simply tweak the dial.
The dimmer-controlled receptacle also has a second function: it's a dandy speed control for a Dremel rotary tool. I never use a rotary tool on reeds to grind, but only to clean sometimes with the wire wheel or hard cotton buff. You can dial the speed down precisely to attain much better control, especially if you are routing out wooden parts. Looking forward for the results of these wax experiments! Thanks for sharing your findings!
-
A friend gave me block of bees wax that I'm tempted to turn into reed wax. I understand the recipes but need to know what form of rosin or resin to use?
Is it basically the same type of rosin that is used for violin bows?
Is it the kind of resin that I've made by letting pure gum spirits of turpentine sit for a couple of months to thicken and then heat it to drive off the volatiles (used for varnish making)?
What's the original source material for this particular additive to reed wax?
-
What is the disadvantage of using pure beeswax?
-
What is the disadvantage of using pure beeswax?
It's too soft to hold the reed plates firmly enough. Adding rosin makes the wax somewhat harder and stickier.
-
Best way I have found to make sticks - Pour some molten wax onto a tray of hot water - when cool you have a sheet of wax. Score it - chill it - snap it into sticks.
To make sticks I pour the wax into a flat container the slice with a sharp knife and straight edge. The temperature has to be just right for this, too cold and the wax is brittle and cracks as you cut, too warm and the cut heals after the knife has passed. A warm room temp seems to work so I'd guess about 20 to 25 C.
Which of the two is the better method I wonder? Maybe both are equally sound.
I guess I could experiment myself, but I am hoping that someone can convince me one way or the other.
I see that 'CGM Musical Services' supplies wax sticks that are ~6mm thick.
Is that a good size, or would thinner/thicker sticks work better?
-
I see that 'CGM Musical Services' supplies wax sticks that are ~6mm thick.
Is that a good size, or would thinner/thicker sticks work better?
I've used many miles of Charlies wax sticks and they are fine. The size is a bit variable but that just means I have to feed faster/slower onto my waxing iron.
-
Pouring wax onto water to cool has the advantage of avoiding the whole slab of wax getting stuck to the bottom of a tray. There is one thing to watch out for. If you have hard water, even slightly hard, hot beeswax will react with the lime in the water which denatures the wax. To avoid this either use rainwater, or add a little citric acid to the water.
-
I've mafecthe occasional bowl of gloop too. It seems to be less of a problem if you add the oil after the wax and rosin have melted together.
To make sticks I pour the wax into a flat container the slice with a sharp knife and straight edge. The temperature has to be just right for this, too cold and the wax is brittle and cracks as you cut, too warm and the cut heals after the knife has passed. A warm room temp seems to work so I'd guess about 20 to 25 C.
I have experimented with making a small quantity of reed wax for emergency repairs,, I read somewhere that some recipe's include Turpentine and since resin dissolves fairly readily in turpentine, (must be genuine turpentine NOT white spirit) I dissolved the resin in turpentine first, allowing overnight for it to dissolve then mixed in the already melted wax . the result appeared to be successful, I have used it to do emergency re-attachments to loose reeds and so far none have failed the oldest being about year ago, and the wax appears to be unchanged ....of course only time will tell how successful this is.
-
I've used many miles of Charlies wax sticks and they are fine.
That's good to know.
Pouring wax onto water to cool has the advantage of avoiding the whole slab of wax getting stuck to the bottom of a tray. There is one thing to watch out for. If you have hard water, even slightly hard, hot beeswax will react with the lime in the water which denatures the wax. To avoid this either use rainwater, or add a little citric acid to the water.
Thanks for the tip.
-
Re Resin - When i made up my wax for fettling my 1040, I used beeswax bought in one of our local markets, but had no idea how to buy resin at all, so I begged scraps of old violin rosin from my middle sister and powdered it down with my kitchen mortar and pestle. The resultant wax came up perfect in use (thank you for the recipe Theo!)
For the waxing process, again I had no idea how to adapt my modeller's soldering iron at that time, so I used it as it was - VERY CAREFULLY. I held it away from the wax, just enough to get the stuff flowing properly. This did work, though my work grew progressively more sloppy as I worked up the board. I now know better - DO NOT TRY TO DO THIS AT HOME! :Ph
-
You can find lots of rosin by searching for colophony powder. A non-thermostatic soldering iron through a cheap dimmer is an inexpensive way of melting wax, especially for repairs, without getting it hot enough to smoke (good ventilation etc...).
When I looked at the cost of making reed wax I didn't think it economic for small quantities. I will do it one day, just for the experience. Then it'll be back to Charlie.
-
...A non-thermostatic soldering iron through a cheap dimmer is an inexpensive way of melting wax...
Aren't all commercially available soldering irons thermostatically controlled?
-
No. They just heat up to a temperature where the heat lost to the surroundings balances the the heat output of the element - thermal equilibrium, and far too hot for melting wax.
-
Mine is similar to this, from Maplin. (https://www.maplin.co.uk/p/antex-12w-mains-soldering-iron-yu90x) It's an earlier model, they must have been doing these for years. There is a 25W version, too.
I have a "proper" thermostatic soldering iron but I don't know if it goes low enough. Anyway it's reserved for soldering. (:)
PS I was given the dimmer control. As Theo says, too hot to use without one.
PPS it's like this, set at about half-way from memory. (https://www.kenable.co.uk/product_info.php?products_id=8018&gclid=EAIaIQobChMIm-fDq4iZ2QIVbLXtCh3NnwuHEAQYBCABEgJu7PD_BwE)
-
My two cents on reed wax.
I typically use a 60/40 Wax to rosin ratio. To this I add about 5% by volume Castor and Linseed oil. One of the old repair guys told me about the castor oil and how it helped adhesion. I melt the wax and pour most of it into a copper pan I have. I leave a little melted wax in the melting can and add the rosin (the rosin has really crappy thermal behavior and the wax helps it melt) i melt the rosin and add the castor and linseed oil to help it melt. When melted I pour the rosin into the wax in the copper pot and heat and stir it a bit to help it mix.
As it cools i sometimes get the gummy sludge people spoke of. By running a stick around on the bottom you can collect it into a lump and remove it. My untested theory is that this is possibly honey sugar in the wax that by heating has been candied. It could also be oxidized rosin. Tasting or seeing if it dissolves in water would solve this mystery. It would also help you as this might throw your wax/rosin ratio off so you could adjust it if this happened.
When the wax is still warm I cut out chunks from the pan and roll it like clay into 1/8" sticks about 2' long and roll them up and they go on a peg above the work stations.
I use a soldering iron (temp controlled now days) that I have hammered the tip flat on ,soldered with plumbing solder a flat brass blade, and then drilled through the tip and blade and copper riveted the two together in a couple of places.
My wax is dyed reddish as I get a lot of broken reeds from the Tex-Mex crowd and it helps me see what I did before.
I restored a vintage 1930's Wurlitzer and it had wax that would melt and flow like it was new. It had a distinctive smell when heated like old motor oil, perhaps a bit of a sulfur smell too. Would love that recipe.
-
Heating the wax and the rosin separately first, and getting the wax very hot first and adding the melted rosin to the wax seems to work. But not always. (:)
-
As it cools i sometimes get the gummy sludge people spoke of.
I've had that gummy sludge too. Pretty sure it's not sugar left over from when the wax contained honey. I used to keep bees on a larg-ish scale so I have a lot of experience of working with wax. I used to heat the wax first over a water bath, then add the rosin and always git a lot of gummy sludge. The last batch I made I heated the rosing first directly over the heat with no water bath so as to get a higher temperature. The rosin melted completely and then I added the wax, and finally the oil. Result no sludge at all. My take on that is that the rosing needs more heat than I was using in order to get it fully melted.
-
If you keep bees, you might have a steady supply of wax as a by-product, (?) in which case i can see the sense in blending your own reedwax. However, if you don't keep bees.......what is the benefit of blending your own (as the process seems to be quite awkward, time-taking and even possibly dangerous!) when it's readily available from the likes of the revered Mr Marshall?
-
Having costed it, and got the materials, in small quantities it comes out about even. I shall do it, to scratch the itch and to get the experience, then I will buy it from Charlie.
-
As it cools i sometimes get the gummy sludge people spoke of.
Looks like we are going to have to taste some some to answer this question.
-
As the O/P I'd have been happy to send a taster Kimric, other than I am out of stock and needing to make some more (last of the brew went to Edward to keep his overheads down.
I tried both raw linseed and olive oils, fresh, home brewed (and not over refined) beeswax and cheap and cheerful resin from a supplier to ballet, gymnastic and weightlifting exponents (which arrived twice as the wife had shipped it, then husband shipped it following day not realising) 50:50:5 wax, resin, oil by weight and poured onto warm water in an old grill pan and cut on a board with a pizza cutting wheel into thin strips around 3-4mm sqr.
Theo, Rees and Steve Freereeder had samples, Theo did my Liliput reeds with it but quite sensibly said he'd not risk an unproven wax on customers work, not sure if Rees tried or commented on it, Steve found it fine and had a second batch (but didn't buy the company ;) ) and the only observation I recall was a nicer smell than Charlies, probably as a result of it being fresher wax. The hint of propolis version was not a success due to it globbing up on the iron but with more than a hint (2% ish)is a spectacularly good chucking wax for small turning jobs on the watch lathe.
Will try to remember when I make some more.
-
"last of the brew went to Edward to keep his overheads down"
And very gratefully received it was! With nothing other than remelted old wax to compare it to, I was greatly impressed with Richard's concoction. It is very easy to use, flows wonderfully, and seems to be veeeery strong and sticky when it sets!
I'm going to have to buy some soon, though. Is Mr Marshall's the one to save up for?
-
Another endorsement of Richard's wax sticks from me. I'm on the second batch he supplied me with now.
Flows easily, hardens off well and seems to hold the reed plates very firmly. Smells nice too. I guess it's the propolis. (:)
Comparing it with wax sticks from Charlie Marshall, Richard's wax needs a slightly higher temperature setting (approx 10°C more) to achieve the best flow. Charlie's wax is paler in colour, a little softer to begin with, and perhaps needs a longer time to harden off.
Both types of wax do the job very well.
-
Carnauba wax consists of fatty acid esters (80-85%), fatty alcohols (10-16%), acids (3-6%) and hydrocarbons (1-3%). It is around 20% esterified fatty diols, 10% methoxylated or hydroxylated cinnamic acid, and 6% hydroxylated fatty acids. Carnauba wax has a very high melting point of 82-86 °C (180-187 °F).
-
Edward - I think I could let you have some of mine if you like.It's cast as a shallow block, in a plastic tray, which makes it easy to cut off sticks with a sharp knife. PM me with your address and I will send it to you. It's only sitting taking up space in my "melodeon" tool box. (:)
-
PM sent, thank you.
-
Pouring wax onto water to cool has the advantage of avoiding the whole slab of wax getting stuck to the bottom of a tray. There is one thing to watch out for. If you have hard water, even slightly hard, hot beeswax will react with the lime in the water which denatures the wax. To avoid this either use rainwater, or add a little citric acid to the water.
After reading about wax once again;
Experiment: an attempt to make sticks of wax
a plastic tray
hot water
citric acid
wax that just melted
And now _ patience and wait
But it look ok so far, will put the "cake" in the fridge and later cut it into sticks
-
50/50 beeswax and rosin (no water bath should be used ) heat in a pan on low heat keep an eye on it only needs to be hot enough to melt not cook chips ! when molten add tiny dash of olive oil mix and then pour onto prepared surface (do not get near any water )the surface i find ideal is to put a ceramic tile in a freezer bag and pour out on this it will spread to thickness of around 1/8 inch (3 mm) before setting and can be popped in freezer then removed from the plastic surface of the freezer bag or left if prefered and sliced into thin wax sticks (1/8inch ) reeds waxed in 30 years ago with this still sound . i did try pouring onto water many years ago the worst thing you can do , the wax just spits everywhere in use ,perhaps if allowed to dry for a few months its ok but i wanted it quick
-
I recommend melting the rosin first, then adding the wax. Rosin has a higher melting point and I’ve sometimes had a mass of semi solid rosin that was difficult to combine with the melted wax.