Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Andrew Culwell on September 14, 2010, 11:49:14 PM
-
These are the reeds out of my Hohner Pre-corso Double Ray deluxe. The reed plates look aluminum to me but I am not sure. I am told that the Aluminum Hohner reedplates have less quality sound than the ones with the Zinc plates. Can anyone enlighten me on both subjects?
-
Zinc is usually darker gray in color. Often long plates
though I have some with single plates
-
These are the reeds out of my Hohner Pre-corso Double Ray deluxe. The reed plates look aluminum to me but I am not sure. I am told that the Aluminum Hohner reedplates have less quality sound than the ones with the Zinc plates. Can anyone enlighten me on both subjects?
Just judging from the photos, they appear to me to be aluminum plates. I have a Hohner with zinc reed plates, and they usually color to a dark gray, as Jeff said. As for the quality of sound, only you can make this determination. I would certainly give them a whirl. They look to have a bit of rust, though, and it's not easy to tell the extent from a photo.
-
Those are very attractive looking reed plates, with the name and all! :||: :||:
I pulled this off a WikiAnswers page:
Add two to three drops of 1M ammonia to the unknown solution. Both Al and Zn produce white hydroxide precipitate (Al(OH)3 or Zn(OH)2). Upon addition of excess ammonia (two to three more drops), Zn(OH)2 dissolves while Al(OH)3 remains insoluble. Be sure that you use NH3 solution and not NaOH since Al(OH)3 already becomes soluble with elevated basicity.
This test is only valid if you have only one of the two cations present in solution.
;D ;D ;D
So much being said, your plates look like aluminum. The zinc plates in my 1939 Club are a dark/cloudy grey color and not at all the nice shiny plates you have there. As for the tone of them, honestly, I prefer the more strident tone of aluminum plates, especially in the high register where notes from zinc plates get really mushy (I prefer a wetter tuning for a 3 voice, results with a dryer tuning could vary). Zinc plates, in my experience, have a more open and flutey tone, overall a less focused or cutting tone than what s made by aluminum plated reeds. Although it's difficult to say if that's the only determinant because Hohner may have been using different reed stock in the late 1930s when they put the zinc plates in the box...
-
I, too, prefer the aluminium reedplates, particularly those marked with the "T". The reeds seem to fit the slot more accurately than both the "H" reedplates and the zinc ones, giving a faster response, more apparent volume (harshness???) and greater dynamic range.
However,there is a downside; from my experience, aluminium plate "T" reeds do tend to break more often. Not sure whether it is the way the profile of the more modern "T" reed is machined or if the steel stock used is, in fact, harder and therefore (?) more brittle. More prone to work hardening? Dunno.
Wonder how Hohner's Chinese reeds compare??? Hmmm.
Needs some one to do some quality AB tests perhaps....but that would probably create further mysteries. Know any metalurgical students needing a useful project and having available decent facilities???
But back to the original post, I had a set of those reeds described by AC out of a destroyed Club; definitely aluminium, but a poor fit to the plates and absolutely unuseable. Then I acquired an old Hohner Organola p/acc from the 1930s with the same appearance reeds; a far better fit, probably not as good as "T" reeds, but at least as good as aluminium "H". And the Organola was Hohner's top piano accordion model at the time. The ones in the photo don't look too bad a fit, but it is a small photo.....
-
Wonder how Hohner's Chinese reeds compare??? Hmmm.
where does their steel come from ? ???
oz maybe..........
-
My experience is that Hohner reed quality is very variable, especially those made before the 1950s. The type shown in your photo with the Hohner name stamped on each plate I have always assumed were their best quality at the time. They usually have a good fit of the reed tongue to the plate, and when set up properly will respond quickly at very low pressure. The sound is warm and rounded, but as others have said the maximum volume is less than you could expect from later 'T' reeds.
-
Note the marks on the rivets.
-
Wonder how Hohner's Chinese reeds compare??? Hmmm.
where does their steel come from ? ???
oz maybe..........
The iron ore maybe....
Not sure if we manufacture spring steel here any more, do we?
I recently read that Oz is today a net importer of steel. One guess where it comes from?
Yes, quite right....
-
Are Hohner T reeds still made in Germany?
-
What's interesting is that the individual who I have asked to restore this particular reed block has told me the following. "if the reeds are the zinc frame type and in decent condition, they are the nice sounding reeds - if they are aluminum frame "H" then they are not worth putting money into" I'm just not convinced that this is the case. That's why I'm asking for other opinions.
-
What's interesting is that the individual who I have asked to restore this particular reed block has told me the following. "if the reeds are the zinc frame type and in decent condition, they are the nice sounding reeds - if they are aluminum frame "H" then they are not worth putting money into" I'm just not convinced that this is the case. That's why I'm asking for other opinions.
That's kind of a funny comment for him to make. I guess beauty really is in the eye (or ear) of the beholder. There are many different types of reeds and frames, and in the hands of a good technician I'm convinced that they can all sound quite nice. Especially regarding old Hohners, I haven't heard an one yet that's been restored and didn't sound like it was worth the money ($200-$600, plus initial investment).
-
I tend to agree with you there! I'm going to stick with the original plan and have this box restored with the original reeds. This box is a real beauty and I want it to have that unique sound that old Hohners have.
-
I've watched this thread with fascination as I had no idea one had this choice in reed plate composition. I guess underlying this there is the usual issues of mass and Young's modulus of the material, v weight and machineability. The accoustic coupling between reed and plate will be massive so it makes sense that it affects the sound (we had the same discussion re wood for frames last year).
Elsewhere in engineering the current trend for motorcycle engine blocks is (believe it or not) - magnesium - said to be both lighter and stiffer than aluminium. Googling a bit ... I see it applies to car engines too (http://en.wikipedia.org/wiki/Cylinder_block). Might make for interesting experiment - has anyone tried magnesium alloy reed plates?
More parochially - Colin Dipper once intimated to me that he'd experimented with aluminium as a a reed plate in his concertinas. No idea how many he made though (I suspect one). But I got the impression this was aluminium replacing the wood hexagon - AFAIK Colin's reed plates are brass. My 2dth Chris
-
What's interesting is that the individual who I have asked to restore this particular reed block has told me the following. "if the reeds are the zinc frame type and in decent condition, they are the nice sounding reeds - if they are aluminum frame "H" then they are not worth putting money into" I'm just not convinced that this is the case. That's why I'm asking for other opinions.
Does seem an odd comment, though perhaps influenced by the restorer's interpretation of your intended use for the box. Perhaps the word "nice" is the key.
I think I would be happy with zinc plate Hohner reeds if I were just playing gently at home; yes, gentle, flowing, easy paced, beautiful and peaceful music....Nice!
But for playing with even a hint of aggression at an Irish session, ceilidh band or to accompany morris, aluminium framed reeds are probably the way to go, and I would definitely be inclined to try having your originals restored. Should that fail because of the rust problem, get a decent set of T or even H from somewhere....and perhaps a different restorer (or at least a second opinion).
Incidentally, I just re-reeded an old Hohner Koch 21/8, originally with "H" zinc plates. Some one had already replaced the valves with mylar, rewaxed it and wet tuned it before I acquired it. It now has aluminium plate "H" reeds and the transformation is incredible. From thin, reedy and breathy to punchy and loud. But maybe not what I would describe as "nice" ....
Chris, I'll see your 2p and raise you 10c
-
The old zinc plates sound great dry tuned (unison) as in my old Bb/Eb Double Ray.
For tremolo tuning, aluminium plates are much better.
-
The old zinc plates sound great dry tuned (unison) as in my old Bb/Eb Double Ray.
For tremolo tuning, aluminium plates are much better.
You might have hit the nail on the head there, Rees.
I have a beautiful gold fleck Preciosa with zinc plates, but try as I might to get a decent tone by tuning wet, I cannot seem to do so. Anything beyond 7 or 8 cents at A above middle C does not sound at all good. My preferred option using aluminium plate reeds, 20 cents, sounds decidedly horrible!!!
Personally, I'm not a great fan of dry, or even swing tuning for the sort of music I play. One day (?week? month?) I may just have to sit down and file a set of aluminium "T" plates to size....
I cannot recall ever dry tuning a set of zinc plate reeds, as apart from ITM players, few people over here want dry tuning, and not all ITM folk either; there seems to be a growing demand for a wee bit of tremolo. However, I might experiment with dry tuning the old reeds from the Koch, which certainly don't look in bad condition.
-
Hey guys,
Well, I volunteer to be an approved disposal site for unwanted zinc-plate Hohner H reeds. I like the sound of 'em! You can even send me those oddball ones in the keys of F#, B, C#, E.
Not implying anything negative about the ones that Drew pictured in his original post however, or other good Hohner aluminum-plate reeds for that matter. I certainly wouldn't throw them away. Whether I would bother to clean and tune them would depend on just how rusty they are. If really rusty, it might make make more economic sense to switch in a clean set and save the originals.
PG
-
I've just done a conversion to Bb/Eb with a set of old Hohner zinc plate reeds, tremolo about 15cents, sounds great. Why are we stuck with those squeaky D/G boxes?
-
I've just done a conversion to Bb/Eb with a set of old Hohner zinc plate reeds, tremolo about 15cents, sounds great. Why are we stuck with those squeaky D/G boxes?
I agree, I love the sound of my recently refurbished Preciosa in Bb/Eb, about 10 cents and zinc reeds. My Hohner Morgane is now sounding very shrill.
-
Bb/Eb and A/D are just perfect.
D/G squeaks!
-
Bb/Eb and A/D are just perfect.
D/G squeaks!
*eak*
-
Fiddle players >:(
-
Fiddle players >:(
Fiddle players round here love Bb too
-
The "gold" standard on pre-war bandoneons was also zinc plates.
Steve
-
Bb/Eb is the new D/G around here!
Martyn ;)
-
Bb/Eb is the new D/G around here!
Martyn ;)
Sure is - only lower ;D
Just noticed your 'Hohnerohner' - very good. Worthy of a badge.
-
I have a Castagnari Hascy in DG with the proprietary "swing" tuning.
Three reeds LMM... and in my estimation, as finely built the Hascy may be, and even with the low reed engaged
D/G
squeaks
-
Maybe it needs more tremolo....
Or a mouse trap! >:E