Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Ajax on September 19, 2010, 06:27:51 PM

Title: Newbie and a UK source for brass springs
Post by: Ajax on September 19, 2010, 06:27:51 PM
Newbie here. I have a 'for spares or repair' one row unnamed melodeon, with two stops (one a dummy), brass reeds, leather valves, possibly from around 1900, and probably a very low budget model, judging by the materials and rough finish. One mitred case end is lost from the reed-plate end, so there is at present no possibility of (leaking) bellows pressure at all; and so as to the key it's in I can only test by unhygienically blowing/sucking the top reed, which gives Ab and high Eb (using tuning-fork A440 as the standard). [Is this a  - to us - high G and D then?]

I'm using this melodeon to find out what is involved in a complete repair; but I do really want to repair it, and not discard it or make it even less restorable than it already is.

One torsion (V-shape) spring is missing beneath a button lever, having been (I suppose adequately) replaced by the previous owner with a compression (cylindrical) spring. Perhaps I could make a replacement torsion spring? I've just now seen Bernard Loffet's demo for spring making [http://diato.org/trucs/fabr_ressorts/image003.htm] but can't find a UK supplier of suitable brass. Any suggestions for a retail supplier of small quantities of 'roll-your-own' wire or the springs themselves? Thanks.

P.S. Terminological confusion (mine). . . the leather 'flaps' covering the reeds are, it seems, called 'valves'. O.K. But in the forum I find that the pallet 'fingers' (that cover the holes) may also be called valves. So is it 'reed valves' and 'pallet covers' or what?
Title: Re: Newbie and a UK source for brass springs
Post by: HallelujahAl on September 19, 2010, 07:01:03 PM
Send a piccy of the spring type and size that you want to Charlie Marshall at CGM  (http://www.cgmmusical.co.uk/CGM_Musical_Services/Welcome.html) - he's a good supply of all sort of accordion/melodeon springs and will more than likely have just what you need. I've made my own springs - but have found a decent supply of spring wire difficult to get hold off myself so I'll be watching this thread with interest! Kind Regards - AL

Oh, btw welcome to the best forum on the planet!
 ;D
Title: Re: Newbie and a UK source for brass springs
Post by: nomad on September 20, 2010, 01:17:12 PM
hi

cgmmusical.co.uk have a good selection of stuff that i doubt you would find else where. I have used Charlie a few times and would highly recommend him.

Title: Re: Newbie and a UK source for brass springs
Post by: Theo on September 20, 2010, 02:00:33 PM
hi

cgmmusical.co.uk have a good selection of stuff that i doubt you would find else where. I have used Charlie a few times and would highly recommend him.



If he can't help then make your own, but don't try to find brass wire.   Steel piano wire, also known as music wire is available from model shops and specialist music shops and will do the job.   You may need to use a slightly thinner wire than the original brass as steel is stiffer.
Title: Re: Newbie and a UK source for brass springs
Post by: waltzman on September 20, 2010, 04:44:52 PM
brass springs or bass springs?
Title: Re: Newbie and a UK source for brass springs
Post by: Broadland Boy on September 20, 2010, 07:43:11 PM
Ajax, welcome from a fellow tinkerer

Brass, if used for a spring, is likely to have been work hardened by being pulled through a draw plate which you may not have, better to use Phosphor Bronze which is generally supplied in this condition, or as Theo suggests, piano wire.

Richard
Title: Re: Newbie and a UK source for brass springs
Post by: Ajax on September 20, 2010, 08:45:14 PM
Many thanks for the rapid, helpful advice. All much appreciated and taken on board. Yes, I did mean brass (not bass) springs. --- Brass in appearance, anyway.

With regard to my P.S. about terminological confusion (reed valves, pallet 'valves', pallet covers) is there a full glossary of melodeon lingo available on this site or elsewhere?
Title: Re: Newbie and a UK source for brass springs
Post by: Theo on September 20, 2010, 09:52:29 PM
Terminology is a mess:
UK. : valve is the leather or plastic flap fitted to each individual reed
US and Europe valve is the thing lifted by a button to sound a note,  in UK this is usually called a pallet
Title: Re: Newbie and a UK source for brass springs
Post by: Bill Young on September 21, 2010, 11:32:14 PM
I bought a length of piano wire to make springs from a chap called Alex in Kent, on eBay. He has various gauges of wire available. Here's a current listing. (http://cgi.ebay.co.uk/Piano-Wire-Brand-New-3m-length-/110588960637?pt=UK_MusicalInstr_Keyboard_RL&hash=item19bf9d9f7d)
Title: Re: Newbie and a UK source for brass springs
Post by: melodeon on September 22, 2010, 03:39:26 PM
Yanks and  "Kajuns"  also call the pallets ( Britvalves)  "flappers"

Pallets works for me... my  mother was a flapper..
SimplePortal 2.3.5 © 2008-2012, SimplePortal