Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Jon Loomes on September 25, 2010, 11:02:43 AM
-
Ok....
As the Music Room's melodeon lackey, I work surrounded by boxes I can't afford. I sold my decent boxes a while back for reasons too depressing to go into here, but I'm starting to gig again and will need a box sooner or later. So...I'm having a go at a rebuild/customisation type project. All opinions on this greatly welcomed.
Old German pokerworks: Bloody marvelous, Ideally, I'd really like 12 basses. Can I rip the bass mechanism out of a corona and modify the levers? I think there should be enough room for the pallets etc.
Now, I've got a very pretty carcass off a Student 1 accordion - Tyrolean Pattern, cream with red, green and gold, you know the one... Same dimensions as a pokerwork, but with the bass rows slightly offset. I guess I'm going to have to fill and re-drill and make a new (whatever you call that raised platform thing that the inner row of basses go through).
I'm guessing that the big job with this will be making new soundboards with holes cut in the right places for melodeon reedblocks. Irritatingly, as an accordion it has a 22 key right hand - so 22 holes in the board - It'd be great if I could just shut one of them off, but does anyone know if the holes are centred the same? After all, it would make manufacturing sense if the Student 1 used more or less the same factory templates as the diatonics.
Many thanks,
Jon
-
Mike Rowbotham in St. Ives has done just that, there's a picture on his website. Not with the 12 bass though....
Good luck
-
Now, I've got a very pretty carcass off a Student 1 accordion - .....
Simon Ritchie has one done like this. I recall him saying that it was a huge amount of work and he wouldn't want to do it again!
-
Hi Jon et al
first off, you know you can find the occasional 2-row with 12 basses - they are pre-pokerwork and either pressed wood or black/gold pre-pokerwork (what I call 'Seashells' pattern - see middle box middle row of website). Also, the occasional perloid instrument. I've several 12 bass instruments at the moment.
As regards the Student 1 conversion, I'd encourage you to have a go - I'm making a second one of these at the moment, the first was so good. Fabulous casing and great sound. I used reeds from a C/F box rearranged for D/G - not the original Accordian reeds. Also, don't worry about the extra holes/reedblock space - I saw it as a 'plus', allowing me to fit an additional button low down on the G-row - I have low B/C on that, with the usual accidentals in the usual positions. There's a photo on my website showing my 22 button Student 1 melodeon.
As regards fitting 12 basses, you've got to source bass and chorus reedblocks plus action mechanism - a good source is an old Student 2 Piano Accordian. I've not done this on a pokerwork, but I have on several Erikas. There are 3 ways to go - one is to block off the original soundboard holes and re-drill. A second is to cut out the old soundboard and graft in the soundboard from the Piano Accordian - after all you're raiding it for most of its bass end - might as well have the soundboard too! -Fitting is easier than you might think. The third approach is to accept the soundboard holes already in the instrument and drill additional ones for the 4 extra basses. It's do-able on an Erika (just) but I'm not sure about a pokerwork size instrument. You get issues with positioning and contact with the internal folds of the bellows. I think inserting the 12-bass soundboard from the P.Acc is the most effective/easiest way to go.
Send me a PM and I'll give you my phone number; we can have a chat about the project if you like.
cheers
Mike R
-
Am I correct in thinking that our Rees did Simon Ritchie's Student 1 conversion?.
I don't know exactly how it was done but Kepa Junkera has a 12 bass Pokerwork so it is possible.
I've had an Erika waiting for a 12 bass conversion for some time now and I've got to get on with it now that I've got no boxes to play, I just need to get hold of a Corona II bass mechanism. I'm going to make new blocks from scratch rather than trying to find some that fit, they shouldn't be too hard after this silly 8-string baritone guitar some nutter convinced me to make. ::)
-
ok...so far so good. I've got a student II bass end. Looks like it should fit quite easily and I think I'm going to go with grafting the board rather than swapping all the bits. The thing that has me stumped is, how to get those thermoplastic buttons off without breaking them or pouring hot water into either of the two boxes that I've got sprawling over the kitchen table? Any ideas, or should I just snap the bloody things?
Cheers,
J
-
Do you run to a hot air gun in your kit or know someone who has John ?
A bit of kitchen foil to act as a bib round the stems would help preserve the finish (of the box, not buttons)
HTH
Richard - currently torturing apples with a ten ton jack :-X
-
Now that's not a bad idea. I don't have a hot air gun unfortunately, but following the same line of thinking, maybe a soldering iron applied to the levers would be enough to transfer the required heat into the buttons. Trouble is, my soldering iron is many miles away...
Nicky Clarke ceramic hair straighteners it is...
Cheers,
J
-
Nicky Clarke ceramic hair straighteners it is...
Cheers,
J
You silly twisted boy >:E
Anything with a flame is likely to damage, wot about a turn of bootlace or string round the stem, held reasonably tight and 'floss' it until the friction either warms it to plasticity or it ignites the firelighters which should be inside ?
Can't think of anything else - Apollo 13 might not have made it back on this level of inventiveness :|||:
Richard
-
Soldering iron worked for me - cost me £2.50 from a cheapie shop. Still working actually.
;D
AL
-
Well, Nicky Clarke won the day....both mechanisms now removed with buttons preserved for later...
Having thought it al through a bit more (and given the limited tools at my disposal pending moving house) I'm actually going to drill new holes in the original soundboard rather than do the graft and transfer. This will mean that I have to make new a new reed block for the chords and reverse the triangle pallet direction, but at least if I bugger it up I can put the pallets back the right way and have another go with the graft method. Or make a new board. Just trimming felts and leathers now. Next job will be to fill the old holes in the LH of the casework and drill new ones to accommodate 12 basses and get rid of the annoying p accordion slant between the rows.
Cheers,
J
-
Am I correct in thinking that our Rees did Simon Ritchie's Student 1 conversion?.
Tim "Banjo" Normanton did all the horrid casework and action stuff, I just supplied the various knackered instruments and fitted the reeds and blocks.
As I recall, the melodeon keyboard was riddled with woodworm so Tim kind of rebuilt it with fibreglass.
Simon loves it!
-
"Next job will be to fill the old holes in the LH of the casework and drill new ones to accommodate 12 basses and get rid of the annoying p accordion slant between the rows."
Done... well, half done. Not drilling the outer row holes till the filler in the old holes has set properly. Suddenly, it's starting to take shape, though.
-
Well....it looks like a melodeon, and a most pretty one at that. But the L/H mechanism is awful. Truly horrid. Everything is bent (ooooh, Jules! a bona hohner...) and twisted, (a word, dear reader you may note, that has already been used in this thread. R/H coming on nicely though, except the only treble blocks I can find are a set I tuned to G natural min in order to learn how to tune reeds. So it's all a bit odd at the minute. I'm half tempted to fill in the extra bass holes in the carcass and go back to 8 bass, but I can't help feeling that that's maybe a bit defeatist. Am I better off quitting while I'm only a bit behind? Oh reader, what shall I do?
-
Keep calm and carry on!