Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: malcolmbebb on October 21, 2010, 07:29:46 PM

Title: Prettying up a Pokerwork
Post by: malcolmbebb on October 21, 2010, 07:29:46 PM
Yes, I know it's a crap title...

MAD is setting in, and I can't even play one yet. I have just acquired a single row Hohner Pokerwork which is in need of some TLC.

1) It's pretty grubby. What should I use - or avoid - to give the case generally a clean?
2) The fingerboard is apparently plastic, I've got a lot of grot off, any recommendations to get it looking nice?
3) Someone had stuck tape - maybe gaffer/duct tape - over the Hohner logo. The tape was gone but some adhesive remains. Any suggestions to safely remove it without lifting the paint? (Surgical spirit? )
4) The buttons are a bit grubby - any special treatment to bring them up?
5) The cloth behind the grill and bass panel is falling off and grotty - is it easy to replace?
6) Finally - the straps are original, but quite hard and seem to be getting brittle. Is there any treatment to preserve/soften them?

Thanks
Malcolm

For the curious - it's in C, German, four bass, "Marca Registrada", and loud. All notes sound OK to me but second button up has a very odd beat note on push. There's some rust on the metalwork and light rust on the grille, which is slightly bent. The bellows seems in good nick (orange/yellow colour). And I paid fifty quid.
Title: Re: Prettying up a Pokerwork
Post by: HallelujahAl on October 21, 2010, 07:38:06 PM
Quote
I paid fifty quid
Great! It'll always be your best box.
 ;D
Title: Re: Prettying up a Pokerwork
Post by: Theo on October 21, 2010, 08:47:02 PM
Good price!

For a really thorough clean you need to start be taking it apart. 
Pull out the bellows pins,
undo the two screws that hold the fingerboard
remove all the straps,  give them some rough treatment, bend and twist them, if they crack or break throw them away, old perished leather is not worth keeping.

With the fingerboard off you have better access to the buttons for cleaning.  My method is to rest the levers on the edge of a sink with the buttons hanging over the sink, then give them a good scrub with an old toothbrush and your favourite detergent.   I use Cilit Bang Lime and Grime!

If the fingerboard is plastic and has no felt inside then you can safely wash that in hot soapy water.

Woodwork can be cleaned with a damp cloth with some detergent,  to remove sticky label residue I use lighter fluid.

If the metal corners are rusty they can be replaced, though they are generally difficult to remove.  You may be able to clean them up with steel wool.

etc, etc, etc
Title: Re: Prettying up a Pokerwork
Post by: malcolmbebb on October 22, 2010, 07:25:14 PM
Thanks for the ideas - I'll have a go on the weekend.

Cheers

Malcolm
Title: Re: Prettying up a Pokerwork
Post by: melodeon on October 22, 2010, 08:18:29 PM
If the cloth is original with the original  glue, it can be removed with warm water and a bit of scraping with a nbox cutter blade used as a scraper.. or scraper of your choice.

I found suitable grille cloth at a fabric shop... stiffer for the treble side than the bass side
I bought enough cloth for 40 accordeons for under $10 US


I used water soluable glue and a brush and:

brush the glue on the sound boards and lay the cloth in place....    simple

oif you want to stiffen cloth... spray with clear acrylic "fixative" which can be gotten at an art supply store..
I use
or dip in egg white thined with water...hang toi dry   install as described.
Title: Re: Prettying up a Pokerwork
Post by: Ebor_fiddler on October 22, 2010, 10:52:01 PM
My Hohner cost me £25, but after doing up (I don't think what I did can really be classed as "restoration" - though it did have its comedic bits) it's my favourite. All I need now is to get rid of the bass rattle!  :||:  ;D
Title: Re: Prettying up a Pokerwork
Post by: Broadland Boy on October 23, 2010, 02:26:16 PM
£50 - a very nice aquisition ;)

Does anyone know if there is a product available (or a recipe) to touch up the black woodwork finish with?
 I cant decide if this is a stain, varnish or laquer but appears pretty constant from early to late Hohners, a bit of battle scarring looks fine but I've some places on a couple of my boxes, esp. keyboards which could do with a touch up - any successes ?

Richard
Title: Re: Prettying up a Pokerwork
Post by: Theo on October 23, 2010, 03:01:27 PM
If its plain black, (or if all the gold has gone)  then you can achieve a quick freshen up with black french polish, applied with a cloth rubber.
Title: Re: Prettying up a Pokerwork
Post by: Broadland Boy on October 24, 2010, 08:40:12 PM
Thanks Theo,

I had tried a little meths to see if it was f/p and nothing lifted so reckoned it must be some other finish - Ithat being the case it will take f/p with no ill effect to the original and I only wanted enough to kill the bare wood look.

I've heard of something called Berlin Black but don't know what that is - anyone here know ? probably something for metalwork or the inside of Naval binoculars....

Richard - whos skills in painting and finishing are not terribly good  :(
Title: Re: Prettying up a Pokerwork
Post by: malcolmbebb on October 24, 2010, 09:09:28 PM
My box has come up nicely for a good clean, and I'm watching the other traffic with interest. It will never look new, but it looks happier, the grille has straightened up and the metal work looks like it will mostly clean up.

However, on dismantling I was presented with a number of loose valves. So a few more questions:

1) They were obviously glued on - so what glue should I use to stick them back on? Or should I replace them?

2) I'm missing one, from the B/G (funnily enough, all four are adrift but I guess one has fallen out)
Can anyone suggest where I might source a replacement?

3) Most are on the front, the reed blocks are glued on, so I will have to remove the individual reeds. They are held in place with some upholstery pins and a daunting amount of wax. I've no doubt the process, tools etc are described somewhere - can anyone point me in the right direction?

Finally, there is a number - 76 - stamped inside. Would that be the manufacture date?

Thanks

Malcolm
Title: Re: Prettying up a Pokerwork
Post by: sticky fingers on October 27, 2010, 08:29:02 PM
a-ha the number 76, no that would be the number of skips it has been thrown into before you bought it, or the number of people that thrashed the dogs out of it on the trade stall at the last festival before the vendors saw you coming. a-ha (only joking) seems like you got a bargain, stick with it. sf
Title: Re: Prettying up a Pokerwork
Post by: Lester on October 27, 2010, 08:41:26 PM
My box has come up nicely for a good clean, and I'm watching the other traffic with interest. It will never look new, but it looks happier, the grille has straightened up and the metal work looks like it will mostly clean up.

However, on dismantling I was presented with a number of loose valves. So a few more questions:

1) They were obviously glued on - so what glue should I use to stick them back on? Or should I replace them?

You should probably replace them Charlie Marshall's (http://www.cgmmusical.co.uk/CGM_Musical_Services/Welcome.html) your man. Stick them on with Evostick or Bostick

Quote
2) I'm missing one, from the B/G (funnily enough, all four are adrift but I guess one has fallen out)
Can anyone suggest where I might source a replacement?


See 1)

Quote
3) Most are on the front, the reed blocks are glued on, so I will have to remove the individual reeds. They are held in place with some upholstery pins and a daunting amount of wax. I've no doubt the process, tools etc are described somewhere - can anyone point me in the right direction?


A 1 Row is by far the least easy box to start on so I will leave this to the more professional amongst us to answer

Hope you are having as much fun/aggravation as I am on my Pokerwork refurb
Title: Re: Prettying up a Pokerwork
Post by: malcolmbebb on October 27, 2010, 09:34:28 PM
Quote

A 1 Row is by far the least easy box to start on so I will leave this to the more professional amongst us to answer

Hope you are having as much fun/aggravation as I am on my Pokerwork refurb

LOL thanks for the tips! You have no excuse, you've been playing one for yonks!

I made the mistake of telling my wife about my first attempt, aged about five, to dismantle a clock. Winding it up first was not a good move, I discovered.
I bought one of those little toy boxes in C, took it apart - the comments she made when she saw that were nothing to the leg pulling I got when I took the Hohner apart... 
As an engineer (not certified, for those following another thread) I think these boxes are great.  I like things that are designed to be dismantled, maintained, and put back together and I'm learning a lot from this site (and concertina.net) about how to do it.
Musically I'm very much a learner - but I'm enjoying learning. And Morris tunes.
Just to really show how daft I am, I'm also learning on C/G and D/G Anglos. Trouble is, a DG melodeon (I have a DG Pokerwork on loan) plays more like a C/G anglo than a D/G and it's the D/G I really want to learn. Ho hum
SimplePortal 2.3.5 © 2008-2012, SimplePortal