Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Telemorris on December 09, 2010, 05:22:31 PM

Title: Presswood Pokerwork Rebuild
Post by: Telemorris on December 09, 2010, 05:22:31 PM
I thought I'd create one thread for repair questions to do with my Presswood Pokerwork rather than start many small threads.

First obstacle I ran into last night was in trying to remove the Bass mechanism for cleaning and replacing the felt washers under the buttons (picture below). I thought I should remove the buttons in order to remove the mechanism but I can't figure out how to get the buttons off. Is there heat involved? I've looked in the archives and haven't found anything about removing the buttons. I'm probably not searching using the exact correct terms. Any suggestions?

Thanks,

Ed
Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on December 09, 2010, 05:28:47 PM
My personal preference is to undo the nail hinge where the button rods meet the mechanism, again my preference is to ship the heads off the nails and replace them. It is v important that you mark the rods in some way to get them back in the position they start in as they are all subtlety different.

The buttons are just an interference fit but are hard to remove and I am not sure, never having done it, how well they will stay in place if removed and replaced.

I know Theo's preference (judging from a previous thread) is to remove the buttons and so it must be possible and probably sensible, I guess he will be along soon.

ps, your bass mechanism looks to be badly bent out of shape for the rods to be sticking out that far if they are still connected?
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 09, 2010, 05:51:10 PM
Thanks Lester. I looked at the bent nail hinge and thought I'd rather not touch that. At least that was my first impression when confronted with this puzzle. I'll have to try that tonight unless Theo can advise how to remove the buttons. I'd like to extract the entire mechanism for cleaning, another reason for removing the buttons.

Have you ever enlarged the holes and bushed the holes with felt? It seems like a nice upgrade.

I'd already removed the screws from the mechanism and the rods were pushed up as a result when I took that photo. Not to worry. When the mechanism is screwed in, the buttons sit at a normal height and register inside the holes the way they are supposed to. I took photos of the instrument to document the starting condition and will post them on Picasa later.
Title: Re: Presswood Pokerwork Rebuild
Post by: Steve_freereeder on December 09, 2010, 06:00:06 PM
Have you ever enlarged the holes and bushed the holes with felt? It seems like a nice upgrade.
I'm about to do that on a Hohner Erica. Lester has kindly supplied me with replacement nails for the rod pivots (which I need to dismantle to get access to the button holes), and I have bought some proper concertina bushing felt from David Leese in North Wales which I hope will be just the job. Will report back as and when I progress with the work.

http://www.concertina-spares.com
http://www.concertina-spares.com/catalogue11.htm

Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on December 09, 2010, 06:07:22 PM

I'm about to do that on a Hohner Erica. Lester has kindly supplied me with replacement nails for the rod pivots (which I need to dismantle to get access to the button holes), and I have bought some proper concertina bushing felt from David Leese in North Wales which I hope will be just the job. Will report back as and when I progress with


Photos please as it is on my list for my super-Erica I'm building.
Title: Re: Presswood Pokerwork Rebuild
Post by: an bosca ceoil on December 09, 2010, 06:55:35 PM
If the existing buttons are sound, cut/straighten the pins and remove the rods!
The buttons are interference fit and may not take kindly to being levered off.
New replacements are easy to come by, but inferior finish.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 09, 2010, 07:34:56 PM
Here are my photos of the instrument before repairs.

http://picasaweb.google.com/TeleMorris/PresswoodPokerwork?authkey=Gv1sRgCLuXpqru26SMfg#
Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on December 09, 2010, 07:43:25 PM
Here are my photos of the instrument before repairs.

http://picasaweb.google.com/TeleMorris/PresswoodPokerwork?authkey=Gv1sRgCLuXpqru26SMfg#

I would recommend disconnecting the springs before either unscrewing or replacing the mechanism as they place a lot of strain on the very small brass screws until the mechanism is screwed down with all the screws.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 09, 2010, 07:55:37 PM
I would recommend disconnecting the springs before either unscrewing or replacing the mechanism as they place a lot of strain on the very small brass screws until the mechanism is screwed down with all the screws.

While I didn't think of that before removing the screws to take off the mechanism, I did disconnect the springs to put the mechanism back later. It's a good safety measure. Thanks Lester.
Title: Re: Presswood Pokerwork Rebuild
Post by: Steve_freereeder on December 09, 2010, 09:13:53 PM

I'm about to do that on a Hohner Erica. Lester has kindly supplied me with replacement nails for the rod pivots (which I need to dismantle to get access to the button holes), and I have bought some proper concertina bushing felt from David Leese in North Wales which I hope will be just the job. Will report back as and when I progress with


Photos please as it is on my list for my super-Erica I'm building.
Right-oh. It may take me a while to get going with it though, at this time of year.
Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on December 09, 2010, 11:51:34 PM
Right-oh. It may take me a while to get going with it though, at this time of year.

That's good for me, the reeds for super-Erica are coming from Father Christmas so no great hurry (:)
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 10, 2010, 12:08:33 AM
Lester, would you mind explaining "Super Erica",  please? I'm really curious now.
Title: Re: Presswood Pokerwork Rebuild
Post by: RGF on December 10, 2010, 12:43:44 AM
Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink (http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink)
Bob
Title: Re: Presswood Pokerwork Rebuild
Post by: Malcolm Clapp on December 10, 2010, 01:14:37 AM
Telemorris, I use heat to remove the bass buttons. Use a soldering iron to heat the rod as close as possible to the underside of the button. As a rule of thumb, as soon as you catch a whiff of melting plastic, withdraw the heat and gently ease the button off.

However, I'm sure the said "whiff of melting plastic" is possibly dangerous to health and probably carcenagenic, maybe even haluciagenic, so I accept no responsibility.... etc. etc.

But hey, life's a risk.... >:E



Title: Re: Presswood Pokerwork Rebuild
Post by: waltzman on December 10, 2010, 04:11:27 AM
Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink (http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink)
Bob

Nice work.  The heat shrink tubing on the wooden dowel is brilliant.
Title: Re: Presswood Pokerwork Rebuild
Post by: Gandy on December 10, 2010, 08:33:56 AM
Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink (http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink)
Bob
Nice work.  I need to re-visit the bass on my Pokerwork.
Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on December 10, 2010, 09:02:43 AM
Lester, would you mind explaining "Super Erica",  please? I'm really curious now.

I have purchased an Erica body, old style - flat grille, wooden keyboard, and am getting a set of Cagoni italian  reeds (http://www.cgmmusical.co.uk/CGM_Musical_Services/Reed_Plates.html#5) from Father Christmas. It will probably be 4th button start and I will tune it drier than my Hohners , thus giving me a lightweight, hopefully Italian sounding, box rather than lugging one of my Salterelles around. This is my project for the New Year.

All will be revealed  (:)
Title: Re: Presswood Pokerwork Rebuild
Post by: Owen Woods on December 10, 2010, 04:14:07 PM
Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink (http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink)
Bob

Wow, Bob! Really lovely work.

Interested by the ultrasonic cleaner. Is this one that uses water as a solvent? Does it work well?
Title: Re: Presswood Pokerwork Rebuild
Post by: Bill Young on December 10, 2010, 04:42:16 PM
Well, I'm far from expert on this, but I've done a half dozen or so (with much help from others here) and actually happened to take a few photos along the way. So, on the chance that they may be of help to anyone here, I've posted them at Picasa, along with some explanatory notes.
You can find them here: http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink (http://picasaweb.google.com/robtgf/HohnerPokerwork?feat=directlink)
Bob
That's really nice work. What a great sequence of photos.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 10, 2010, 04:43:47 PM

snip

Interested by the ultrasonic cleaner. Is this one that uses water as a solvent? Does it work well?

I'm very interested in the ultrasonic cleaner too. How does it work for rust?
Title: Re: Presswood Pokerwork Rebuild
Post by: RGF on December 10, 2010, 04:49:11 PM
I'll check with my friend and see if she can't write a brief description, and I'll post it here. I just drop them off and pick them up!

Bob
Title: Re: Presswood Pokerwork Rebuild
Post by: strad on December 10, 2010, 05:09:54 PM
Just googled Ultrasonic Cleaner and they're quite cheap now. We used to clean oscilloscopes in an ultrasonic bath at one place I worked. Sparkle, sparkle until they were switched on! Then the liquid lurking in the mains transformer caused some interesting effects. But for things like reeds I would imagine they'd be really good. Not a lot of use for bellows, though.

Nigel
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on December 10, 2010, 05:21:09 PM
I've considered using an ultrasonic cleaner fro reeds,   but I have one worry about making the metal so clean that it becomes more prone to corrosion in the longer term.  This could be especially a problem because of the possibility of galvanic reactions between the two different metals.  I'm sure there are ways to avoid this with the right cleaning solutions, and use of a de-watering/corrosion inhibiting solutions.
Title: Re: Presswood Pokerwork Rebuild
Post by: Andy Simpson on December 10, 2010, 08:07:05 PM
The cheap ones really aren't worth it, you need one of the proper industrial ones that start at a couple of hundred quid.

I bought a £40 one, (when it was on sale for £25), and I've tried different cleaning solutions and none of them really shift stubborn rust, wax or glue. They make it a lot easier to remove but they don't get very good results, even cleaning for ages and ages in pretty strong solvents. Boiling in plain water is more effective and cheaper. In both cases I applied camelia oil to the reed tongues and no problems with rusting so far.

I tried boiling some reeds that I thought were beyond redemption in pickling vinegar and after only a few minutes nearly all the rust was gone....along with the blue oxide layer on the base and undersides of the tongues.... ::)
Title: Re: Presswood Pokerwork Rebuild
Post by: Owen Woods on December 10, 2010, 08:54:00 PM
The cheap ones really aren't worth it, you need one of the proper industrial ones that start at a couple of hundred quid.

I bought a £40 one, (when it was on sale for £25), and I've tried different cleaning solutions and none of them really shift stubborn rust, wax or glue. They make it a lot easier to remove but they don't get very good results, even cleaning for ages and ages in pretty strong solvents. Boiling in plain water is more effective and cheaper. In both cases I applied camelia oil to the reed tongues and no problems with rusting so far.

I tried boiling some reeds that I thought were beyond redemption in pickling vinegar and after only a few minutes nearly all the rust was gone....along with the blue oxide layer on the base and undersides of the tongues.... ::)

Cool, I suspected as much.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 10, 2010, 09:17:05 PM

I tried boiling some reeds that I thought were beyond redemption in pickling vinegar and after only a few minutes nearly all the rust was gone....along with the blue oxide layer on the base and undersides of the tongues.... ::)

Can't you apply steel bluing to restore that oxide layer again? Never tried the stuff before so I don't know how it works. Only enough knowledge to get myself into trouble.
Title: Re: Presswood Pokerwork Rebuild
Post by: Ebor_fiddler on December 10, 2010, 11:43:13 PM
DO NOT trust them to clean CD's as they claim to be able to do! Fortunately I experimented on one of the copies I make for the car, but the surface bubbled up quite alarmingly. Otherwise ours is not quite as good as the manufacturer says it is - if that's not an oxymoron.  :|glug
Title: Re: Presswood Pokerwork Rebuild
Post by: Andy Simpson on December 11, 2010, 12:19:09 AM
I'm glad I bought mine when it was on sale, a complete waste of money. I thought it would help me avoid loads of tedious scrubbing and creating fine dust but all it did was make it slightly easier whilst adding considerably to the overall time it took to clean them. I tried it with water, water with washing up liquid, several special, (and expensive), cleaning solutions, neat and diluted meths and even coca cola.

I really recommend boiling in slightly diluted white vinegar for rusty levers and action parts though, works a treat. However, I would also recommend doing it outside on a camping stove and not in the kitchen, the smell it creates is truly vile. I needed a hell of a lot of Febreze, scented candles and open windows...

I haven't put the reeds back in the box yet but they appear to be OK and sound fine when plucked with a pinger. The removal of the oxide layer alarmed me and I pulled them out straight away but I don't see why the reed shouldn't be alright without it, other than making the underside and base of the tongue a bit more susceptible to rust. The top of the tongue never has an oxide coating and boxes shouldn't really be subjected to the kind of conditions that cause rust anyway.
Title: Re: Presswood Pokerwork Rebuild
Post by: RGF on December 11, 2010, 09:11:46 PM
Here's the info my clockmaker friend sent me about what she does with my reeds while they're in her care. Feel free to ask questions, but I will likely not know the answers! (If I do receive any questions, I will collect them and pass them along.)

I will preface this by saying that I've been fortunate in not having encountered reeds with a great deal of rust on them -- the majority of what I have found, I've been able to scrape off with the broken end of a bamboo skewer or a sanding pencil, etc., prior to cleaning.

I have not  encountered any subsequent rust accumulation after doing this, but then again, they do not live in an environment that is conducive to rust.  And the experiment is only two years old -- who knows, they may collapse in an oxide cloud next year.

In other words, I'm not endorsing this as the best way to do it. (Insert disclaimers here.) I'm a hobbyist at this, but it seems to be working...for now. Until something better happens to comes along. Your mileage may vary.
________________________________________________________________________________


Clockmakers technique for cleaning reeds:

Soak individual read blocks in a 50-50 mix of mineral spirits and xylene for 1/2 to 1 hour to soften the wax.  Caution xylene is nasty, do this out side and/or wear a respirator.  Do not breath in the xylene. Wearing nitrile gloves (do not use laytex as they are not a barrier to xylele) remove one read block at a time from the solvent mix and brush the semi dissolved wax off onto paper towels then set aside to let the rest of the solvent evaporate.  There will be a slight dirty haze left on the reeds.

Lay out reed blocks in basket of ultrasonic tank (it doesn’t matter if they overlap) then submerge and run tank for 3 to 5 minutes.  Rinse with running water then dunk in denatured alcohol.  Dry 3 or 4 blocks at a time on a towel using a hair dryer, flipping often.  Done.

The solution I use in my ultrasonic is Polychem Deox-007 nonammoniated cleaning concentrate.  It is diluted 7 parts water to 1 Polychem.  One gallon from “Merritts” (clock repair supplier) is about $24.00.  I’ve also used Historic Timekeepers concentrate, again diluted 7 to 1, a pint from “Timesavers” is $9.00.  I’ve heard that other detergents/degreasers like Simple Green work as well but I have not tried them.  Just be careful of creating excess bubbles by the ultrasonic.  If I didn’t have the ultrasonic tank Simple Green and a tooth brush I think would work fine.

Look for ultrtasonic tanks at Harbor freight.  They go on sale and are just fine for occasional use (either the little jewelry ones or the bigger gallon size).

For removing rust from linkage arms I’ve soaked them in Captain Lee’s Rust Away from SPRA’-STRIP, inc.  It is a phosphoric acid solution.  Or a mechanical method is using 3M Radial Bristle Disc in a dremel tool (white 120 grit to blue 400 grit).  I get these from Jewelry suppliers like Rio Grand or the Hobby supplier Micro-Mark.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 12, 2010, 07:08:13 AM
I made good progress today.

I removed and disassembled the treble mechanism, and made a small table for holding all the parts separately. The springs for the front row were kept separate from those for the back. I've uploaded a photo of my table below. The rust was removed from all the keys and other mechanical parts. Once the parts were cleaned, I applied a light coat of wax to provide some protection from rust. The wax also provides a minimal lubricant though it's not sticky and will not attract dust. Glad I remembered that trick.

Added later: Wax - I used a floor wax with Carnuba, not reed wax. The canuba based wax dries to a hard finish and will help protect the steel. I use it on our long swords for my morris team. The wax really helps the blades to slide against each other when making a lock.

All the pallets for bass and treble are now cleaned, the old leather removed and surfaces sanded, ready for new felt and leather. Still waiting for the box from CGM.

I also made a small table to fit over the bellows frame as a mini tuning table. I'll post a photo to my Picasa folder tomorrow.

Tomorrow I'll clean up the bass mechanism and reassemble the treble mechanism. The I'll probably start removing the old bellows tape.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 13, 2010, 04:55:04 PM
Bellows repair questions:

I've been looking through the archives about removing bellows papers and tape. I started stripping off the original bellows tapes. They look and feel like paper with a coating of some kind on the outside. I'm trying to remove them dry by gently separating them from the layer of paper underneath with a thin tool that can slide between the two layers. I've tried using a damp sponge to put some water on the old tape only but that doesn't seem to work. The coating seems to prevent the water from soaking through the tapes. Any water that makes it onto the old decorative papers causes those papers to pill up if I rub with the lightly dampened sponge to try to get the tape residue off.

I've been fairly successful with the thin tool at separating the tape from the paper though the paper underneath is sometimes coming away in spots where the glue did not bond to the cardboard. At this point I'll need to replace the papers in the folds as well - I wasn't all that thrilled by the brown and white spotted paper in the first place and was thinking of putting on something new anyway.

Please advise about techniques for removing the paper tape and the old layer of original paper safely without harming the bellows card underneath. The bellows card itself is in good shape. Is it best to stick to a dry technique to strip the old tapes, and use fine sandpaper to get the old bits of glue and paper off? Do I cut strips of cloth the correct size of the tapes, wet them and let them sit on the tapes for awhile or is that likely to cause problems with the bellows?

If I'm going to replace the bellows papers and tape, do I need to completely remove the old paper or can I put new paper over the old? What's the best sequence of tasks for chasing leaks coupled with tape and paper removal? Should I remove the tape and paper as much as possible but wait to re-cover the bellows until I get gaskets and pallets installed to test for air leaks?

Tallships, any advice would be greatly appreciated. Did you strip off down to the original card stock? It's hard to tell from the photos in your thread.
Thanks
Title: Re: Presswood Pokerwork Rebuild
Post by: Owen Woods on December 13, 2010, 05:48:29 PM
I'd be interested in this as well. My imperial needs retaping but I'm determined that it doesn't need repapering, as that seems like a pretty horrible job. Haven't started trying to remove yet.
Title: Re: Presswood Pokerwork Rebuild
Post by: an bosca ceoil on December 13, 2010, 06:09:08 PM
You should have asked some of these questions before you started the job (:)
It should be possible, though tedious, to remove the paper "tape" without damaging the covering paper.
Sometimes, but very rarely, the taping will almost fall off but usually gives the problems you mention to varying degree.
You need to split and tear off as much of the waterproof coating first, so that the remaining "tape" can be dampened enough to soften the glue. Once this is achieved it is fairly simple to scrape/wipe the residue off without damaging the paper covering the folds.
Once you have done this you need to clamp the bellows until they are thoroughly dried out!
One problem with recovering the decorative paper, apart from making the bellows stiffer, is that by rights it should go on before and under, the metal corners, so you may be in for some fiddly tailoring.
As regards air leaks, again, you should have looked before you started the job. If the bellows were originally airtight retaping them should not create any leaks.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 16, 2010, 07:35:24 PM
Removal of old paper and tapes is almost finished on the Presswood bellows. The original paper was only partially attached in many areas so removal has been a case of tearing the paper off to find untouched card stock underneath. I'm down to the card and gussets on three sides and am about to finish the fourth.

I'm not finding it as tedious as others seem to. Something of a meditative frame of mind hits me as I'm doing the fine details lifting paper from the edges of the metal corners. I have not removed the corners having seen a post from Theo in the archives warning against that. I'll need to figure out how to cut and attach the papers at the corners once I'm to the papering stage since I'll be attaching around the edges of the metal corners. Any suggestions for how to cut the papers at the corners?
Title: Re: Presswood Pokerwork Rebuild
Post by: Owen Woods on December 17, 2010, 12:51:29 AM
having seen a post from Theo in the archives warning against that.

Yes, I seem to remember that he was quite emphatic in that warning ;D
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on December 17, 2010, 08:37:02 AM
Sometimes the corners are fairly loose, if they come off easily it may be worthwhile
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 19, 2010, 02:43:05 AM
Theo,

The corners are all quite tight so I've removed the paper up to the joint between the metal and the leather.

I've removed the reeds from the reed blocks and am in the process of cleaning the wax and old valve glue off. One post in the archives mentions "white spirits" for removing wax. Would that be the the same thing as denatured alcohol here in the US?

Also, how clean do I need to get the reed blocks and the reeds? I've scraped the wax off down to the surface of the wood but there's still some residue.
Title: Re: Presswood Pokerwork Rebuild
Post by: Graham Spencer on December 19, 2010, 06:02:02 AM
Denatured alcohol is called "methylated spirit" in the UK; "white spirit" is turpentine substitute (NOT turpentine!!!), derived from paraffin (kerosene), once used almost universally for cleaning paintbrushes and still readily available in ironmongers (that's hardware stores over there!) and d-i-y outlets.  I believe it's also called Stoddard solvent in some places.
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on December 19, 2010, 09:50:01 AM
I don't like the idea of using solvents to clean wax off reeds or blocks.  My method is to scrape off the wax with a blunt knife (actually an old kitchen knife with a broken blade with the broken end ground to a right angle) then I give the reedblocks and reeds a good scrub with a soft wire brush designed for cleaning furniture after chemical stripping of old paint.    Brushes for sued shoes also work well.  Finally brush off loose dust with a 1/2" paintbrush.  If you have a compressed air supply to blow everything clean that would be ideal.
Title: Re: Presswood Pokerwork Rebuild
Post by: malcolmbebb on December 19, 2010, 10:39:49 AM
I don't like the idea of using solvents to clean wax off reeds or blocks. 
Is that because it opens them up to corrosion, or a different reason? Interesting because there was a mention somewhere of using an ultrasonic bath which might have a similar effect.
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on December 19, 2010, 10:46:49 AM
I was concerned on several grounds, but mainly that its just not necessary.   I've rebuilt dozens of old boxes over the past few years and the worst problems I have had with reeds is an occasional bit of loose dust getting stuck in a reed when its first played. 

Using solvents have the following downside:
possible long term increase in corrosion risks.  This is a bit of an unknown, but a risk I'd rather not take.
the risk of solvent washing debris into the more inaccessible crevices,  not a problem with ultrasonic cleaning
fire risk
health risks of inhaling solvents

But mainly its just not necessary in the vast majority of cases.

I have thought about using ultrasonic cleaning, but if I did the liquid would be water/detergent based rather than using organic solvents.


Title: Re: Presswood Pokerwork Rebuild
Post by: Broadland Boy on December 19, 2010, 04:05:19 PM
I have used ultrasonic cleaning on jewelry / watch / instrument parts and it certainly reveals defects such as poor stone settings either mechanical or 'glued' and can clean enough to allow crack detection to reveal fatigue fractures at the root of teeth etc. in terms of preventitive maintenance fetching accumulated crud or rust out of a fractured reed might allow this to be spotted, although I suspect if at this stage of dying the trained ear ought probably to detect something amiss (? Theo / Rees ?) rather than it falling off mid session......

Unless I want to strip laquer as part of the clean I tend to use clean soft warm water an a drop of detergent with a rinse in clean warm water or sometimes meths, detergent does leave a film on metals. To strip laquqer I add a spot of caustic soda - don't use this on Aluminium that you want to keep a decent surface finish on.  Theo's warning on solvent use, particularly as the cleaning process both heats and may liberate some of the more volatile fractions of solvents even at room temperature should be noted.

The original blueing is an oxide coating from heat treatment and offers a degree of corrosion protection but not much, oiled or waxed gives a better result.
If the blue is 'essential' to you, it can be renewed by using a cold gun blue but this is nasty stuff and offers less protection in my experience than hot blueing even if oiled. I have to admit to using an alternative cold blueing method which you will not find in mainline use, I have a number of items with originally blued components in my 'museum', an unheated and partly below ground level shed ! and I have found that the most persistent blueing of components which are not regulalrly cleaned or polished is to use the blue equivalent of the humble black, waterproof magic marker pen, several thin applications with enough time for the previous one to dry off will leave a finish that is not easy to tell from hot blue.

I know that use of liquid corrosion barriers is not favoured due to the tacky surface which will pick up every bit of passing dust, however there are one or two which leave a thin dry coat which lasts for a very long while, the one I use on the brightwork of my steam engines is Shell Ensis liquid, several grades but the long life one if diluted with white spirit or paraffin will dry in about a week in a warm dry placeand if not abraded last almost indefinitely, can be removed with a wipe of the same solvent.

I will be trying this on my DG Pokerwork sometime, once I have persuaded the light rusting off the reeds and will let you know the result in 20 years time if I'm still about;)

Anyone else with a damp workshop etc, I keep a tobacco tin  of Ensis on a foam pad with some little foam bits that can be used as wipers, any tool which is used intermittently gets a quick wipe over with this after use and / or resharpening before being put away, the few seconds wiping it off next time make up for not having to de rust and resharpen the edge - put some in you used Febreze bottle for heavier applications - Solvent hazard warning applies to this as well ;)

Richard
Title: Re: Presswood Pokerwork Rebuild
Post by: RGF on December 19, 2010, 08:04:50 PM
Richard,

I will pass this along to my clockmaker friend -- Thanks!

Bob
Title: Re: Presswood Pokerwork Rebuild
Post by: Falseknight on December 19, 2010, 09:42:18 PM
I use ultrasonic cleaning for the final cleaning of machined components for subsea and aerospace use.

You are not going to remove chemically attached corrosion,even with heavy duty units, alkaline cleaners and high temperatures.  Ultrasonic cleaning works by generating cavitation on the surface of the component to be cleaned - water is one of the best 'media'.

If you can find a processor, vapour degreasing is going to be a better option, finally using ultrasonic cleaning for the finish.

The industry standard dewatering oils (Rustilo, etc.) are going to be problematic - they attract dust and have limited life span.  Since you have to provide corrosion protection, consider phosphate dips -though how this will affect tuning,and how tuning will affect corrosion life, I shudder to think.
Title: Re: Presswood Pokerwork Rebuild
Post by: Rob2Hook on December 20, 2010, 05:48:46 PM
I used to sneak my pushbike chain in to work and clean it in the ultrasonic bath.  I used a jar of parrafin in the water bath (like a bain-marie) and the chain came out shedding all the grit and grease.  As it was hot and dried quickly, I had to have a tin of chain lube ready melted to dunk it before it rusted!

I have used chemical bluing on a modified sump plug for a Ford prototype.  They forgot to leave room for it so we had to mill them down and refinish them.  Looks good, but I don't think the finish is particularly hardy on a car!  Should be OK inside a box, though, unless you drag it through the snow...

Rob.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 27, 2010, 10:52:33 PM
I've attached valves to the C row and started tuning. I'm raising the pitch of the instrument up to A=440 and am doing preliminary tuning of the reeds before waxing them onto the blocks. I've created a tuning box that allows me to have easy access to the tongue, flip the plate over to tune the other side and switch to the next plate. I've attached some photos below.

One puzzling thing. The push and pull reeds for buttons 6, 7, and 8 do not want to sound. I get a squeek, groan, high pitched overtone, flapping warble, but not a note, though I do hear air passing through the reed plate. The valves are well attached, do not rub against the side of the sounding chamber and open easily to allow air to pass. I tried different amounts of pressure, I adjusted the set of the reed tongue to a larger and smaller gap but there was no change in the ability of the reed to speak, no matter amount of pressure when pushing or pulling. I also checked that there was no fluff or other obstruction, passed a .002" feeler guage around the edges of the tongue and chamber and checked the tongue to make sure no parts were rubbing against the sides of the chamber. I also pulled a valve off one of the reeds to make sure there was no possible blockage to the air flow. Nothing helped. All of the lower reeds had sounded their notes just fine.

After puzzling over this for awhile and trying out various fixes, I pulled the "clamp" piece (see the second photo) off while the bellows was still falling/sucking, and the reed started to sound. For some reason the reed will speak when in an "open" system but not in a closed system. I tested the other "reluctant" reeds with this new setup and they all happily sounded! I don't know why.

Has anyone noticed this before? I haven't found anything in the archives about this but I may have missed something. I just don't know whether to wax the reeds into the reed block and hope that the reeds will sound in that situation.
Title: Re: Presswood Pokerwork Rebuild
Post by: malcolmbebb on December 27, 2010, 11:09:20 PM
Third photo? - I can only see two... ???
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 27, 2010, 11:23:01 PM
Third photo? - I can only see two... ???

For some reason the second one would not post. The photo I'm referencing is the second one. I'll edit that last post accordingly. Sorry for the confusion. Here's the "second" photo, I hope.
Title: Re: Presswood Pokerwork Rebuild
Post by: docEdock on December 30, 2010, 11:40:11 AM
If I'm understanding your experiment, removing the "clamp" created a rectangular opening adjacent to the tip of the reed. Doing so during either a bellows push or pull caused the reed to vibrate in pitch. Yes? 

Humm, I'm hypothesizing that:

1) You were able to achieve a lower pressure with the clamp open than you could with even the most sensitive bellows work
or
2) The abrupt drop in the pressure gradient at the reed energized it to vibrate at a pitch (rather than a harmonic) in a way that a more gradual gradient created by moving the bellows did not.
or
3) The turbulence introduced by an opening near the tip of the read, energized it to vibrate in pitch.

To my mind, Occam's razor suggests 1 above, but your own experience may provide more evidence for 2 or 3. (Actually, I'm hoping that someone who really does knows about the fluid dynamics of semi-chaotic systems will read my speculations and -- with a groan and roll of the eyes -- explain what's really happening. I mean, really, all this jargon thrown around by an amateur -- like a red cape to a bull. Actually you started it when you mentioned "open system" and I remembered struggling through those physics lectures.)

Here's a question: if the opening were at the base of the reed would you get the same results?
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on December 30, 2010, 12:06:04 PM
I get a squeek, groan, high pitched overtone, flapping warble, but not a note, though I do hear air passing through the reed plate.

These are usually symptoms of the reed tongue either being obstructed by a bit of airborne debris (sometimes too small to see with the naked eye) or the reed tongue coming into contact with the side of the vent.  The latter can be a result of the reed tongue being off centre, damage to the edge of the vent leaving a projecting burr, or occasionally the reed having the beginnings of a crack causing it to bend slightly sideways.
Title: Re: Presswood Pokerwork Rebuild
Post by: diatonix on December 30, 2010, 01:45:52 PM
I notice that the beige coloured spring valve covering the white plastic valve is disproportionally long. Was that originally a longer valve that was shortened?
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on December 30, 2010, 01:55:05 PM
The length of the with and beige parts looks normal.
Title: Re: Presswood Pokerwork Rebuild
Post by: diatonix on December 30, 2010, 02:50:10 PM
Assuming that  it is a German M. Grimm valve, the beige part should be appr. 1/3 shorter in order to allow the white part to open satisfactorily. It looks wider than necessary, indicating again that it was probably meant to cover a larger reed. It's perfectly alright to adjust the length of plastic valves (within reason) as long as one remembers to cut the covering parts correspondingly. By not doing so, sound quality can suffer significantly.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 30, 2010, 06:42:36 PM
Assuming that  it is a German M. Grimm valve, the beige part should be appr. 1/3 shorter in order to allow the white part to open satisfactorily. It looks wider than necessary, indicating again that it was probably meant to cover a larger reed. It's perfectly alright to adjust the length of plastic valves (within reason) as long as one remembers to cut the covering parts correspondingly. By not doing so, sound quality can suffer significantly.

The valves come from CGM (http://www.cgmmusical.co.uk/CGM_Musical_Services/Reed_Valves.html#7). The white/beige valve is the smallest valve in the set. I'm not aware of the need to cut the upper piece of plastic. The kit comes with four sizes of valves, two and three part vinyl valves plus the plastic covered leather valves. Given what you're saying, most if not all should probably be adjusted in some way. Can you please explain the principles?

These are usually symptoms of the reed tongue either being obstructed by a bit of airborne debris (sometimes too small to see with the naked eye) or the reed tongue coming into contact with the side of the vent.  The latter can be a result of the reed tongue being off centre, damage to the edge of the vent leaving a projecting burr, or occasionally the reed having the beginnings of a crack causing it to bend slightly sideways.

Thanks Theo,

This set of reeds appears to be in fairly good shape. There's no rust to speak of and most of the reed plates are clean and the notes sound clearly. There's very little oxidation of the aluminum, unlike the zinc reeds in one of my other project boxes.

I've been using a set of feeler gages (.0025",.003", .004") to clean out the vent and edges of the reed tongue. I inspect the edges of the tongue and vent against a strong light, looking for any small breaks in the passage of light around the edge of the tongue and checking for an even amount of light to ensure the tongue is on center. Do you have any suggestions for cleaning out the vent and getting hidden particles out from under the tongue?
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on December 30, 2010, 07:20:18 PM
Bright light inspection is good.   Feeler gauges are not ideal, I prefer to use brass for getting under and around the reed tongue, because it is softer an less likely to damage the soft aluminium round the edge of the vent.
Title: Re: Presswood Pokerwork Rebuild
Post by: diatonix on December 30, 2010, 07:40:17 PM
@telemorris: If these valves are the smallest in the set, and if they really are Grimm valves (but then, where else should they come from?) they have definitely been shortened after they left the factory. The smallest sizes (#11F 25mm, #12F 23mm have only white covers, #13F 22mm consists of only 1 layer), they cannot be neither #9For #10F because the beige part is too long (#9F:total length 28 mm, beige spring valve 12mm / #10F total length 27 mm, beige s.v. 11,5 mm). As a rule of thumb the length of the covering part in a 2piece valve should  be visibly less than half the total length.
I wouldn't be surprised if these valves could, in a way, account for some of the phenomenons you described earlier.
The letter F stands for "Folie" (plastic).
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 30, 2010, 08:27:26 PM
@telemorris: If these valves are the smallest in the set, and if they really are Grimm valves (but then, where else should they come from?) they have definitely been shortened after they left the factory.

I did cut the valve in the photo to length after the glue had dried. I'll cut the upper (beige) portion to half or less than half the length of the valve. Now I'm wondering about shortening the three piece valves. I've uploaded a photo of four reeds with the un-cut valves glued on. These are treble side reeds.
Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on December 30, 2010, 08:33:30 PM
I would only have used the two right hand side size valves on the treble end, the others are to big. I would also have trimmed he overlapping bit (technical term) to be the same proportion as it was on the uncut valve - hopefully you understand that, if not I will try again  ;D
Title: Re: Presswood Pokerwork Rebuild
Post by: diatonix on December 30, 2010, 08:43:11 PM
Exactly, Lester. Of course, the correct valve for the correct reed would be preferrable, as the thickness of the plastic may vary. For the last  reeds on the block that require valves I'd go for a valve without cover.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 30, 2010, 09:17:08 PM
I would only have used the two right hand side size valves on the treble end, the others are to big. I would also have trimmed he overlapping bit (technical term) to be the same proportion as it was on the uncut valve - hopefully you understand that, if not I will try again  ;D

Thanks Lester. Yes, your comments/instructions make sense. I could pull off the valves I've put on so far and match the valve length to the chamber length. Are you thinking I should not have used the large white leather valve then? I'll need to count the valve blanks I have and make sure I'll have enough valves in the correct sizes to do 84 reeds. I know there are a couple of extras for each size.
Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on December 30, 2010, 09:28:35 PM
I would only have used the two right hand side size valves on the treble end, the others are to big. I would also have trimmed he overlapping bit (technical term) to be the same proportion as it was on the uncut valve - hopefully you understand that, if not I will try again  ;D

Thanks Lester. Yes, your comments/instructions make sense. I could pull off the valves I've put on so far and match the valve length to the chamber length. Are you thinking I should not have used the large white leather valve then? I'll need to count the valve blanks I have and make sure I'll have enough valves in the correct sizes to do 84 reeds. I know there are a couple of extras for each size.

I would only use the largest valves on the bass reeds
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 30, 2010, 09:35:24 PM
CGM provides a separate group of reeds for the bass side. I'll see what I can do about changing the valves around to conform to more correct sizes and cut the valve layers to the same proportions as the full size valves. Thanks very much for this help.
Title: Re: Presswood Pokerwork Rebuild
Post by: malcolmbebb on December 30, 2010, 09:41:41 PM
To what length should the valves be positioned/cut? Just overlapping the cut-out, or rather more?
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 30, 2010, 09:42:13 PM
For the last  reeds on the block that require valves I'd go for a valve without cover.

The last two sets of plates/notes for each row did not have valves originally and the advice in the archives has been to refrain from putting valves on them. Oh, you're saying to remove the beige piece of plastic? I could cut it back to the place where the beige piece is glued on.

Title: Re: Presswood Pokerwork Rebuild
Post by: diatonix on December 30, 2010, 09:49:28 PM
Yes, that's quite alright. I did that myself once, when I had run out of #13F.
I'd be interested in knowing whether your reeds with more suitable valves now behave as they should when being pre-tuned.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 30, 2010, 09:52:38 PM
To what length should the valves be positioned/cut? Just overlapping the cut-out, or rather more?

Good question. What might help is a photo of a reed plate with properly sized valve. The adjacent reed chamber is a good reference for how much overlap of the valve is appporiate.

Diatonix, I believe you mentioned you thought the valve in the original photo (http://forum.melodeon.net/index.php/topic,5547.msg71520.html#msg71520) was too wide. What do all of you think is the correct width/overlap of a valve on the chamber? Is it necessary to cut a valve down in width as well as length?



Title: Re: Presswood Pokerwork Rebuild
Post by: diatonix on December 30, 2010, 10:17:39 PM
When dealing with plastic valves, the overlap can be minimal, say 0.5mm. Leather and combi valves: about 1 mm, allowing for possible shrinking. Too much glue is another frequent error, about a square (the width of the valve being its sides) is enough, maybe a little less when dealing with smaller valves, a little more with larger valves.
I wouldn't deem it wise to cut your valves down in width as well. Possible damage is likely to occur and you don't seem to have too many spares.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on December 30, 2010, 10:38:19 PM
Yes, that's quite alright. I did that myself once, when I had run out of #13F.
I'd be interested in knowing whether your reeds with more suitable valves now behave as they should when being pre-tuned.

I'm working from home today and ran down to the shop briefly to try this out. The valves do not make any difference in the sounding of the reeds. I'm going to pull the valves off again since they block the light for visual inspection of the reed and chamber opening.

I'll have to pick up some brass shim stock for cleaning up the chambers and reed edges. Thanks for that tip Theo.

One of the problems with this set of reeds is that the instrument they were in was stored in a damp environment. The reed tongues had moderate to heavy rust which I've cleaned off with very fine sandpaper. However, the zinc reed plates, have a fine white coat of oxide in different places and some small burrs of oxide formed inside the reed chambers in some of the plates, hence my working with feeler gages to try to smooth things out.

It just occurred to me that the rust on the top and bottom of the tongue may also have attacked the edges of the tongues and be causing some of the problems with obstruction, though I don't see any roughness there. Can I very lightly sand the tongue edges with, say, 1200 grit paper? If not, what do I use to clean up the edges of the tongue and the chamber?

Thanks!
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on January 17, 2011, 05:44:32 PM
My progress so far...

I spent the weekend working on the bellows repair. All of the long side papers have been replaced. I found a very nice green paper and used a yellow PVA, Elmers Wood Glue, to glue the papers down. My process was the same as Theo suggested for gluing bellows tape: brush a layer of glue onto a non-absorbent surface, a plastic sheet in my case, put the papers onto the glue "sheet" then put in place. The new papers look fairly good for a first attempt at doing this kind of repair.

Things learned... Use a stiffer, harder type of paper, perhaps something closer to printer paper. The green paper turned out to have two layers though I didn't know that until I started trying to pull it off the glue on the plastic sheet. The paper is certainly thin enough but the under layer would sometimes separate once wet with the glue. Also, the paper would expand a bit from absorbing the water in the glue. As a result the cut ends of the papers that were accurately cut to the length of the tapes came out a bit longer than planned - two or three mm.

I also started gluing on bellows tapes and found the process difficult to control. I'm using the vinyl impregnated(?) 3/4 inch wide tape that Charley Marshall sells. I used the same process that Theo recommends for applying glue, same as above. The tape refused to fold around the edge of the bellows fold and stay in place while trying to apply the next piece. I did use some clothes pins (http://picasaweb.google.com/lester.bailey/BellowsTaping#5547903434161791410) to hold the ends in place, (thanks for that idea Lester). I don't know whether the problem was too little glue, not enough open time to allow the glue to tack up, or that I'm using the wrong kind of glue. I did try some paste that I have "Yes" paste that has proved wonderful for other jobs on the melodeon. If I let the glue dry for a bit before trying to stick the tape down I'd sometimes end up with the glue drying out too much with the result that the tape would not stick at all.

I'm hoping someone can post some of the finer details of gluing up and applying bellows tape. I've found most, if not all, of the descriptions of applying bellows paper and tapes in the archives. I'm hoping that some of these experiences can be helpful to someone else trying to repair their bellows for the first time. This is all a learning process and I'm having fun working on my Presswood Pokerwork.
Title: Re: Presswood Pokerwork Rebuild
Post by: Owen Woods on January 17, 2011, 05:55:41 PM
Hmm, that doesn't sound pleasant. I have a horrible feeling that the papers as well as the tape on my Imperial need replacing, which would increase the work significantly and your experience meets up to my expectations :P
Title: Re: Presswood Pokerwork Rebuild
Post by: Lester on January 17, 2011, 06:18:16 PM
Up until recently I have used Charlie Marshall's "special" paste which is a bit of a pain to apply to the tape, so for the last go I used Polyten PVA Glue (http://www.axminster.co.uk/polyten-pva-glue-prod22032/?pricing=inc) which has a fast 10 minute tack time and is much easier to handle. I just blobbed some on the tape and spread it out with a brush, not too much and not too little (you will soon find out how much). Then just place the tape and it will grab quite easily. After doing  all of one side I still clamp the bellows up with greaseproof between the folds for a couple of hours.
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on January 17, 2011, 06:52:14 PM
I did clamp the tape overnight to ensure a good bond. For clamping I've been using waxed paper to prevent stray bits of glue from sticking the folds together. I fold a piece of wax paper in half such that the doubled piece sticks above the bellows fold. Then I insert a piece of cereal box cardboard between the wax paper. The cardboard is cut to the length of the bellows fold such that it stops just inside the metal corner pieces. The cardboard is also only as wide as the distance from the bottom (valley) of the leather gusset fold to the bottom edge of the metal corner piece.

I've used these cardboard pieces to help apply pressure to the surface of the paper and tape because the metal corners plus bellows tape stands proud of the surface of the bellows card and prevents any real pressure on the glued up surface of the bellows tape. This assembly works quite well.

Thanks for the glue idea. I'll have to look for some here in the US (I still haven't found a source for the cleaning block that you from Maplins). It sounds like the main issue is the tack time and the strength of the tack.

Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on January 17, 2011, 07:04:49 PM
Hmm, that doesn't sound pleasant. I have a horrible feeling that the papers as well as the tape on my Imperial need replacing, which would increase the work significantly and your experience meets up to my expectations :P

Ukebert, don't let the work intimidate you. I'm in the beginning stages if figuring out how to do these repairs. That's why I glue up a few tapes then evaluate the process to try and get the bugs out. Starting with a side that isn't seen when playing also helps to hide any screwups too. I don't expect this first repair to look perfect though I always hope for the best. I do expect to end up with airtight bellows though. I'm also working on an inexpensive instrument that I have the courage to deal with. I would not attempt any of this work on an expensive instrument. I'll also keep trying until I get something that looks right even if it means building new bellows myself, a personal preference since I love to do this kind of work. By the time I get to building a new bellows, I'll have learned how to do these steps.

The only way I can learn how to do this is try, evaluate, try again. Theo and some others on this forum learned by trial and error.
Title: Re: Presswood Pokerwork Rebuild
Post by: Owen Woods on January 17, 2011, 07:10:49 PM
Wise words Telemorris. My method with this kind of thing is to spend huge quantities of time looking up exactly what to do in every case, then when I start to do it I can much more easily work out what to do completely differently from what I'm "supposed" to :P Trial and error is regrettably necessary though, regrettable because I immediately form an emotional attachment to any instrument, and whilst it is supremely satisfying to work on them, I would be very upset if I was to irrevocably ruin them. Tuning and bellows repair are the two things that I am concerned about; for the former I have a box which the reeds aren't amazing anyway, for the latter (which is potentially more of a problem if it goes horrifically wrong) I have a Piano Accordion >:E
Title: Re: Presswood Pokerwork Rebuild
Post by: Telemorris on January 17, 2011, 08:22:25 PM
For me, tuning is the stickier issue since reeds are the sound source and modifying the tongue changes not only the pitch, it changes the harmonics and many other aspects of the sound of an instrument. Small modifications can have huge consequences. Even in an older instrument that might be inexpensive, the reeds might be valuable precisely because they're not made anymore or have a particularly sought after sound. A good case in point is the "junker" that I bought thinking I could use it for learning to tune. When I opened it up I found Hohner H reeds on zinc plates. I've got to be very careful with those reeds.

The bellows are paper and leather and more easily repaired or replaced, within reason. In an older, less valuable instrument, I can experiment and learn. I really would not touch a more expensive instrument because I don't know what I'm doing - yet. After I've done a few of these, I'll have acquired the beginnings of a sense of the process and built up a starting skill set that gives me a certain sense of confidence in how to tackle the basic repairs. Every instrument is different and the repairs are going to be different.

I dare say that Theo, Rees, and the others who are professionals, with all their years of experience, still find themselves with repair tasks that have not come up before and they must, therefore, feel their way carefully to a solution. It's the years of experience with many different repairs that gives a clue as to how to proceed with something new.

I've grown ponderous. Sorry.
Title: Re: Presswood Pokerwork Rebuild
Post by: Theo on January 17, 2011, 11:07:35 PM
I dare say that Theo, Rees, and the others who are professionals, with all their years of experience, still find themselves with repair tasks that have not come up before

Most of what I've learned I have learned from my mistakes :|bl - and I'm still learning. :|bl
SimplePortal 2.3.5 © 2008-2012, SimplePortal