Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: James Fitton on December 22, 2010, 11:01:18 AM

Title: Stopping nuts working loose
Post by: James Fitton on December 22, 2010, 11:01:18 AM
I use the sort of Microvox pick-up system which has a small box you clip to your belt (I don't know the technical name for the box, but I'm sure those familiar with it will know what I mean.) The two sockets for the pickup leads are held in place by screwthreads and internal nuts. One of those nuts has started persistently working loose whilst in use, which causes horrible crackling and spluttering sounds - and the process of undoing the box, retightening the nut, and doing it up again is wildly irritating during a gig. Anyone else have this problem? Would simply supergluing it together be a bad idea? Any better ideas?
Title: Re: Stopping nuts working loose
Post by: Anahata on December 22, 2010, 11:09:27 AM
When it's happened to me, I've taken it home and done it up really tight with a spanner that fits properly and it then takes a long time to come undone again. The sort of fix you do in a hurry in the middle of a gig isn't likely to be satisfactory.

A dab of Loctite would probably do the job, as long as it doesn't prevent electrical contact between internal ground tag and socket body. Alternatively a shakeproof washer - the sort with little teeth around the circumference which dig in as you tighten it up and prevent accidental loosening.

By the way, I think you'll find Microvox's technical name for the battery box is "battery box".

Title: Re: Stopping nuts working loose
Post by: Steve_freereeder on December 22, 2010, 11:10:11 AM
Would simply supergluing it together be a bad idea? Any better ideas?
Superglue is actually a good idea. It was suggested to me by Theo a year or so ago when I had a similar problem of bellows straps working loose.
Just put a tiny bit of superglue on an exposed section of thread just where it contacts the nut. It should stop the nut unscrewing itself, but not stick sufficiently strongly that it can't be undone at a later date.

You could use Loctite thread lock, but essentially it is the same stuff as superglue.
Title: Re: Stopping nuts working loose
Post by: Lester on December 22, 2010, 11:23:45 AM
Had exact same problem at the band's last gig, I went the spanner superglue route and all is now well  (:)
Title: Re: Stopping nuts working loose
Post by: Owen Woods on December 22, 2010, 11:53:44 AM
Another option is getting a but with a nylon insert, which won't come undone and doesn't involve glue, but they tend to be quite chunky and there may not be room.
Title: Re: Stopping nuts working loose
Post by: Ebor_fiddler on December 22, 2010, 08:44:52 PM
There used to be two types of Locktite, Bearing Locktite which was designed to never break, and ordinary, the seal of which could be broken by a sharp twist or tap. If there is any doubt get the second type, it's not as permanent as Sglue.  :-*
Title: Re: Stopping nuts working loose
Post by: Theo on December 22, 2010, 10:04:10 PM
There used to be two types of Locktite,

There are dozens (http://www.loctite.co.uk/cps/rde/xchg/henkel_uke/hs.xsl/fullproduct-list-loctite-4995.htm) of Loctite products now.

Ordinary superglue from the stationery shop is quite satisfactory.  A drop applied to the exposed threads and the face of the nut after tightening the nut is my preference.  A drop of paint or or varnish also does the trick.
Title: Re: Stopping nuts working loose
Post by: Telemorris on December 22, 2010, 10:39:39 PM

Ordinary superglue from the stationery shop is quite satisfactory.  A drop applied to the exposed threads and the face of the nut after tightening the nut is my preference.  A drop of paint or or varnish also does the trick.

A drop of laquer is another way to lock a nut on after tightening. If you use red nail polish, you'll have a visual reminder before removing the nut the next time.
Title: Re: Stopping nuts working loose
Post by: Broadland Boy on December 22, 2010, 11:02:20 PM
Would simply supergluing it together be a bad idea? Any better ideas?

You could use Loctite thread lock, but essentially it is the same stuff as superglue.

Sorry to contradict Steve but the threadlocking Loctite adhesives are a very different compound to the 'superglue' which is usually the 'Hoover' equivalent name used for Cyanoacrylate instant adhesives  (:)

Either would secure the thread but be careful as some of the Loctite threadlockers will do just that, lock a nut to a bolt so tenaciously that the bolt will break before the joint gives - bad news if the job needs to be undone later as considerable heat is the only means of destroying the grip.   >:(

I have loctited joints which need to remain at low electrical resistance such as antenna feed cables to plugs or sockets and however carefully applied there is a detectable increase in resistance as a result, probably not an issue but might affect a low wattage audio signal if this is what is being passed, if this is the case I would cut a suitably sized strip from some Ali baking foil (Oh how I miss the old Kit Kat wrappers  >:( ) and wrap the male part of the thread with some (like using plumbers PTFE tape) you might need to experiment with how many turns but this will result in a nice tight, conductive , reversible threaded joint (if you don't wrap it across two conductors of the circuit that is.......).

A dot of Cyanoacrylate, laquer or silicon sealer may well hold if applied externally but my considerabale experience with Mr Sod and his da**ed Law tells me that it will choose  the least opportune moment to eventually release  >:E

HTH

Richard
Title: Re: Stopping nuts working loose
Post by: Ebor_fiddler on December 24, 2010, 12:07:29 AM
A drop of laquer is another way to lock a nut on after tightening. If you use red nail polish, you'll have a visual reminder before removing the nut the next time.
[/quote]

Surely any properly qualified accordion engineer would use blue nail polish! Good idea all the same, just don't get caught buying pinching it! I'd forgotten that tip from my biking days. Aaah - such larks!  :|bl
Title: Re: Stopping nuts working loose
Post by: Telemorris on December 24, 2010, 01:41:19 AM
Surely any properly qualified accordion engineer would use blue nail polish! Good idea all the same, just don't get caught buying pinching it! I'd forgotten that tip from my biking days. Aaah - such larks!  :|bl

Or red and green nail polish for the Christmas season, purple for repairs done around Easter, and so on. Of course then there's the pagan seasons. What colors are traditional for May day?  ::)
Title: Re: Stopping nuts working loose
Post by: Steve_freereeder on December 24, 2010, 07:57:22 AM
You could use Loctite thread lock, but essentially it is the same stuff as superglue.
Sorry to contradict Steve but the threadlocking Loctite adhesives are a very different compound to the 'superglue' which is usually the 'Hoover' equivalent name used for Cyanoacrylate instant adhesives  (:)
Thanks, Richard. I stand corrected.  (:)
Title: Re: Stopping nuts working loose
Post by: Anahata on December 24, 2010, 11:33:37 AM
Of course then there's the pagan seasons. What colors are traditional for May day?  ::)
Beltane - jumping over fires.... red, perhaps?
"The most common colors associated with Beltane are white and dark green, and red... but also appropriate are all the colors of the rainbow spectrum itself." ... oh well...

Good question, actually: there are lots of correspondences but colours don't seem to feature, at least not in simple  mapping of colour to each pagan holiday. Try The Wheel of the Year (http://www.angelfire.com/wv/SilverMoonsPath/pages/wheeloftheyear.html) and scroll down to "The Colours Used in Rituals".
Title: Re: Stopping nuts working loose
Post by: Theo on December 24, 2010, 02:44:49 PM
Fantastic bit of thread drift, seamlessly from superglue to Beltane,  wow ! (:)
Title: Re: Stopping nuts working loose
Post by: Falseknight on December 25, 2010, 03:34:13 PM
Normally jack sockets have got a castellated or indented locking washer between the nut and the box.Might be worth checking the assemby sequence is correct.
Title: Re: Stopping nuts working loose
Post by: rees on December 25, 2010, 07:25:45 PM
Fantastic bit of thread drift, seamlessly from superglue to Beltane,  wow ! (:)

...... and back to jack sockets. I'm impressed. These people are professionals.  ;)
Title: Re: Stopping nuts working loose
Post by: Owen Woods on December 25, 2010, 07:29:04 PM
Fantastic bit of thread drift, seamlessly from superglue to Beltane,  wow ! (:)

...... and back to jack sockets. I'm impressed. These people are professionals.  ;)

Hah, nothing. I spent over two hours solid on wikipedia (between 2 and 4am) going from the Nobel Peace Prize to... the Nobel Peace Prize. Via lots of other things...
Title: Re: Stopping nuts working loose
Post by: James Fitton on January 02, 2011, 05:01:04 PM
...and, for anyone interested, in the end I went for a dab of Araldite on an already-spannered-tight nut. About 6 gig-hours later, there's not the slightest sign of it working loose. Thanks all.
Title: Re: Stopping nuts working loose
Post by: Anahata on January 02, 2011, 07:45:07 PM
With Araldite, the question is whether you'll get it off if you do need to  :|bl
Title: Re: Stopping nuts working loose
Post by: Broadland Boy on January 03, 2011, 04:39:03 PM
If it needs to be removed in the future but doesn't 'push off' with the nut James, put it in the deep freeze for an hour and it will become brittle enough to sheer or shatter off.

I'm still in the 'investigative period' but am growing in confidence that hot melt glues are useful for this sort of purpose, knew they had to have a use somewhere in the workshop as they're d**m all use as glues for anything permanent (says he throwing down the gauntlett for the next bit of thread drift)

Richard - Happy New Year to All
Title: Re: Stopping nuts working loose
Post by: Lester on January 03, 2011, 04:44:59 PM
Hot glue is good for fixing pallets in place to the treble/bass mechanisms.
Title: Re: Stopping nuts working loose
Post by: Steve_freereeder on January 03, 2011, 05:46:48 PM
Hot glue is good for fixing pallets in place to the treble/bass mechanisms.
Agreed! I went out and bought a hot glue gun especially for this very purpose.
Title: Re: Stopping nuts working loose
Post by: Anahata on January 03, 2011, 07:17:43 PM
You can also get "cold glue" which is like hot melt glue but doesn't have to be heated to such a high temperature, and I've been wondering if it would do instead of wax for holding reed plates down (it can be softened any time by more heat, can't it?)
Title: Re: Stopping nuts working loose
Post by: Lester on January 03, 2011, 07:30:36 PM
You can also get "cold glue" which is like hot melt glue but doesn't have to be heated to such a high temperature, and I've been wondering if it would do instead of wax for holding reed plates down (it can be softened any time by more heat, can't it?)


Not sure why you would look for a replacement for wax which does its job very well?
Title: Re: Stopping nuts working loose
Post by: Anahata on January 03, 2011, 07:39:03 PM
Not sure why you would look for a replacement for wax which does its job very well?
Until it gets brittle and comes undone... is what I was thinking.
Or melts in hot weather (no, I don't know how melting points of glue & wax compare)

I suppose when you have developed the required skill for waxing reeds yourself, you don't have to worry unduly about such things.
Title: Re: Stopping nuts working loose
Post by: Owen Woods on January 04, 2011, 12:35:35 AM
If it needs to be removed in the future but doesn't 'push off' with the nut James, put it in the deep freeze for an hour and it will become brittle enough to sheer or shatter off.

I'm still in the 'investigative period' but am growing in confidence that hot melt glues are useful for this sort of purpose, knew they had to have a use somewhere in the workshop as they're d**m all use as glues for anything permanent (says he throwing down the gauntlett for the next bit of thread drift)

Richard - Happy New Year to All

Some have had success with them for pallets onto arms ;)
SimplePortal 2.3.5 © 2008-2012, SimplePortal