Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: tedrick on January 12, 2011, 03:52:52 AM

Title: old grilles - stamped?
Post by: tedrick on January 12, 2011, 03:52:52 AM
(http://lh6.ggpht.com/_58oS-vwub84/TS0k-2ShnGI/AAAAAAAAKbI/WzVkzv0LGJA/grille.jpg)

how were grilles like this made back in the early part of the previous century? Were they stamped out of a sheet of tin and then plated?

link to full size image (http://picasaweb.google.com/lh/photo/cKPeE34GAvDqdqYtbqb6yg?feat=directlink)

Title: Re: old grilles - stamped?
Post by: Graham Spencer on January 12, 2011, 08:34:37 AM
I'd have thought so, yes - lots of cheap metalware was produced that way.
Title: Re: old grilles - stamped?
Post by: Theo on January 12, 2011, 10:33:56 AM
That particular pattern comes from some of the Saxony factories and is usually made of zinc.   Any plating is usually applied before stamping the holes.
Title: Re: old grilles - stamped?
Post by: Lars on January 12, 2011, 11:46:12 AM
I know an engineer who works at a materials research lab. He knows a lot about metals, fibres, woods, etc., and he also plays the box.

He told me, that in the late 1800's, a thin sheet of protective paper/film with the pattern cut out was applied to the surface of the sheet, and then the whole thing was treatet to some chemical solution. According to him, the parts not covered by the film would be gone in a few minutes, leaving only the desired pattern.

Note: I have personally nothing to back up this information. I was wondering about the very same thing, but I do think this sounds like a plausible explanation.

Now, who knows more?
Title: Re: old grilles - stamped?
Post by: Graham Spencer on January 12, 2011, 11:54:23 AM
I'm sure resist-etching was used for some products, but I'd put money on all the old melodeon grilles I've come across being stampings; there's something about the (sharp!) edges that suggest it, and I'd have thought stamping a far more economic method than resist-etching for mass-produced fittings like these.
Title: Re: old grilles - stamped?
Post by: Theo on January 12, 2011, 11:58:14 AM
Hi Lars,

Resist etching is a well know process still used to make prototype pcbs.

If you look at the edges of the holes in the grill, possibly using a lens, then a punched hole would show some signs of the process with marks on the metal showing the direction of travel of the punching die.  The cut edges will be slightly depressed on the side the die entered, and may be slightly raised on the other side.  Of course corrosion and wear may have obscured tis sort of evidence.
Title: Re: old grilles - stamped?
Post by: Lars on January 12, 2011, 05:58:40 PM
Ah, interesting! I knew someone would know more:)

I talked the engineer - he was in fact referring to some very early concertina ends he had seen.

Now, if only I had one of those presses to make replacement grilles for a few boxes...
Title: Re: old grilles - stamped?
Post by: Graham Spencer on January 12, 2011, 08:42:14 PM
Hi Lars,

Resist etching is a well know process still used to make prototype pcbs.

If you look at the edges of the holes in the grill, possibly using a lens, then a punched hole would show some signs of the process with marks on the metal showing the direction of travel of the punching die.  The cut edges will be slightly depressed on the side the die entered, and may be slightly raised on the other side.  Of course corrosion and wear may have obscured tis sort of evidence.

Absolutely - when I referred to "sharp" edges I meant "likely to tear your flesh" rather than "crisp"!  Maybe "sharp" wasn't the best choice of word - your description of the raised burr on the exit side is exactly what I meant.
Title: Re: old grilles - stamped?
Post by: old geezer on January 12, 2011, 08:54:14 PM
there's a company near here with a laser cutter.
I've seen some of their intricate cut designs of new tina ends in wood
I wouldn't bother using a scroll saw now to make new ends
I haven't seen any of their metal work though, and would assume that this would be the way to go these days
Title: Re: old grilles - stamped?
Post by: oggiesnr on January 12, 2011, 09:10:29 PM
there's a company near here with a laser cutter.
I've seen some of their intricate cut designs of new tina ends in wood
I wouldn't bother using a scroll saw now to make new ends
I haven't seen any of their metal work though, and would assume that this would be the way to go these days

Depends how many you want to make.  If you want lots the same then use a laser or a water cutter.  For one offs a fretsaw is probably quicker and cheaper.

Steve
Title: Re: old grilles - stamped?
Post by: Theo on January 12, 2011, 09:27:24 PM
And if you want any fretsaw work Steve/oggiesnr  is your man.
Title: Re: old grilles - stamped?
Post by: tedrick on December 12, 2011, 05:06:46 PM
Hey guys -
I just learned that I have access to a laser cutter at the Art dept. at my school -

So I'm thinking of trying to replace the grille on my Cairdin mini 21 with something made of plywood -

what thickness plywood should I be looking at? I'm looking for something similar to the Bouebe or any other small box with a wood grille --


Thanks!
Reed
SimplePortal 2.3.5 © 2008-2012, SimplePortal