Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: ofearghail7 on January 19, 2011, 10:38:15 PM

Title: tuning a c/c sharp to b/c erica
Post by: ofearghail7 on January 19, 2011, 10:38:15 PM
Hi i'm new to all this but just wondering what's the best way to tune a c/csharp erica to a b/c? can you put solder on the top of each tongue ? I know probably new reeds would be better but any advice would be great. thanks so much.
Sean
Title: Re: tuning a c/c sharp to b/c erica
Post by: ofearghail7 on January 19, 2011, 10:50:47 PM
oh and are cagnoni reeds decent reeds? how would they compare to hohner? better quality or same? or lower?
Title: Re: tuning a c/c sharp to b/c erica
Post by: Theo on January 19, 2011, 11:03:53 PM
You can put solder on reed tips, but you might find it affects the sound quality.  You can always take it off again if you don't like the result.

oh and are cagnoni reeds decent reeds? how would they compare to hohner? better quality or same? or lower?

Different is probably the best answer.   They make good reeds in the usual different reed qualities.
Title: Re: tuning a c/c sharp to b/c erica
Post by: ofearghail7 on January 19, 2011, 11:18:30 PM
thanks a million. sorry i meant to post that in construction section. thanks a million.
Title: Re: tuning a c/c sharp to b/c erica
Post by: Theo on January 19, 2011, 11:21:09 PM
Now moved!
Title: Re: tuning a c/c sharp to b/c erica
Post by: ofearghail7 on February 07, 2011, 06:54:24 PM
I've tried the solder but it doesn't seem to say on very well. If i was to get a new b set of reeds. would i need bigger reed blocks for the bigger reeds? or would it be a case of altering the current ones?
Title: Re: tuning a c/c sharp to b/c erica
Post by: an bosca ceoil on February 07, 2011, 07:08:33 PM
Hohner reeds would be a straight swap, most Italian ones only need the blocks opening up a bit.
Title: Re: tuning a c/c sharp to b/c erica
Post by: Martyn on February 07, 2011, 07:12:20 PM
I think I would go down the solder route. As Theo says, if you don't like it you can reverse it.
The secret with soldering is making sure the reed is clean. When I add solder to the reed I just give the tip a touch with the file first. The solder should then stick ok.
Personally I don't think the tiny amount of solder needed will affect the sound or response of the reed. You will soon get the feel for how much is needed. Take it slightly lower than required, then raise the pitch with your file.

Martyn
Title: Re: tuning a c/c sharp to b/c erica
Post by: ofearghail7 on February 07, 2011, 09:00:05 PM
thanks a million for tips. i'll stick at it so and make sure the reeds are very clean. theres a bit of rust on some of them. must clean them a bit more maybe.
Title: Re: tuning a c/c sharp to b/c erica
Post by: an bosca ceoil on February 07, 2011, 11:50:46 PM
A very good tool for this job is the butane fired Bernzomatic miniature soldering kit. It  will produce lots of localised heat, includes an extremely fine tip (and enough flux core solder to do hundreds of reeds) that enables you to place the solder exactly where you want it. Safe enough if used with care - just don't tell the loss adjuster what you were doing before the fire started.
Your best bet would be to practice on some of the lower reeds first until you get the hang of it and see how much/little solder you need.
Support the tongue, clean all the rust off and, as Martyn says, brighten the tip, then see where the tuning is at.
If you first just tin about 5mm from the tip, trying not to go right to the edges, you can see what difference it makes and will be able to easily flow more solder on as required.
If you use enough heat to make tidy "bead" that brings the reed lower than you want you will find it easy to lick the top off to sharpen (you can even move the solder to and fro, relative to the tip so long as you do not come too far away)
Might sound obvious but do not forget to scrape off any flux residue before you start filing.
Title: Re: tuning a c/c sharp to b/c erica
Post by: ofearghail7 on February 08, 2011, 12:41:30 AM
fantastic. thanks a million. i'll give it a go.
SimplePortal 2.3.5 © 2008-2012, SimplePortal