Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Christopher K. on February 03, 2011, 11:54:05 PM
-
In another thread, some interesting points were made regarding whether it is the reed type or setup that has a more noticeable/desirable impact on the resultant tone of the accordion. There was also some discussion on whether or not marks on the rivets could be use to positively identify a hand-made set of reeds.
http://forum.melodeon.net/index.php/topic,6045.msg76162.html#new
I think an important question (posed for the benefit of the lay man doing his own work, such as myself :|glug) is that if a set of the highest quality hand-made reeds are ordered from a manufacturer, how can the buyer be sure that he has actually received what he paid for? What are the distinguishing features of a handmade set, and are these qualities shared by other types of reeds like hand-finished, etc.? Do these characteristics vary from one manufacturer to another? ???
(edited to include link to the previous discussion.)
-
Ignoring the arguments over whether or not they make the reeds any better and focusing solely on the way the different grades are manufactured, my understanding is that the Italian reed makers use three broad categories; Voci Commerciali, Tipo A Mano and A Mano.
Voci Commerciali are basic machine made reeds with tongues stamped from steel sheets and riveted onto the plates by machine. AFAIK, there are basic Macchina grade reeds that are pretty much straight off the machine and Export, (usually called "Dural" or "Super Dural" by accordion makers), reeds that receive a little extra attention with more stringent quality control. The rivet heads will either be a smooth dome or a "waffle" pattern as on Hohner reeds.
Tipo A Mano reeds also have the tongues stamped from sheets but are assembled by hand with even more hand finishing and can be distinguished from Voci Commerciali by five flats on the rivet heads from being hammered in.
A Mano reeds have the same hammer marks on the rivet heads but rather than being stamped from sheets, the reed tongues are cut from strips of steel ribbon that are the same width as the foot of the reed so the edges at the base of the tongues will have the blue oxide layer intact whereas TAMs will show bare steel. It's my understanding that the tongues are usually thicker but that's a bit hard to tell visually.
I welcome any corrections or additions.
-
I'd like to add a couple of points...
The reeds I've purchased from Voci Armoniche have iron rivets on the lower grades (Macchina, Export dural) and steel rivets on the higher grades (TAM, A Mano). The steel rivets are a lighter gray colour and I think are always hand-hammered. Steel rivets grip the reed tongue more firmly and are less prone to rust.
The lowest quality reeds use a soft aluminum alloy for the plate. If you look at the sides of the vents, you can see where the aluminum is deformed as it is stamped. Duraluminum (aka dural) plates, which are used on better grades, will have a clean, smooth sides on the vents.
Cheaper reed tongues have a smaller back section where they're riveted to the plate - you can get more reed tongues from a strip of steel that way. Bigger square section gives a better grip on the plate.
-
The reeds I've purchased from Voci Armoniche have iron rivets on the lower grades (Macchina, Export dural) and steel rivets on the higher grades (TAM, A Mano).
Is there any good way to distinguish TAM from A Mano based on the rivets, or do they use the same? Any other ways to distinguish TAM from A Mano?
-Andy
-
I'm a new player, just able to manage a scale on my single row Pokerwork 1040.
However, as a harmonica player (33 years), I know a bit about reeds. Around 20 years ago, Joe Filisko, a toolmaker and master player from Chicago developed a new technique for optimising reeds on Hohner Marine Band harmonicas. This involves careful shaping of the reed profile, requires the hand of a master craftsman. The result is a dramatic improvement in playability (and price) over stock instruments. Since then a number of harmonica customisers have mastered the Filisko method (probably about a dozen worldwide), and produce similar instruments.
In Australia we have a customsier called Neil Graham (www.neilgraham.com.au), I have 10 of his harmonicas. To hear how they sound, check out http://www.harmonicatunes.com/freeharmonicamusic
I'm not sure if similar work is done in the accordion world. It is time consuming, requires great skill and experience and would be expensive
-
The reeds I've purchased from Voci Armoniche have iron rivets on the lower grades (Macchina, Export dural) and steel rivets on the higher grades (TAM, A Mano).
Is there any good way to distinguish TAM from A Mano based on the rivets, or do they use the same? Any other ways to distinguish TAM from A Mano?
-Andy
Hi Andy. Not that I know of.
-
Let me clarify my last post...
No way to tell TAM from A Mano by the rivet, that I know of. For those made in the last +/- 50 years, handmade reeds usually have bluing on the edge of the squared-off part of the reed tongue.
-
Let me clarify my last post...
No way to tell TAM from A Mano by the rivet, that I know of. For those made in the last +/- 50 years, handmade reeds usually have bluing on the edge of the squared-off part of the reed tongue.
Thanks, that makes sense -- since they are cut from a strip, rather than a sheet (someone please correct me if that is wrong).
-Andy