Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: HallelujahAl on February 15, 2011, 10:56:39 AM

Title: Remove old wax?
Post by: HallelujahAl on February 15, 2011, 10:56:39 AM
Now I'm sure there's a been a thread on this before but my searching has been in vain - so here's the question. I want to remove the old wax from a set of reedblocks and re-wax the reeds etc, but what's the best way of removing the old wax? Last time I did this I made a disgusting mess - surely there's a nice clean method of stripping the old wax off  ???
Regards
AL
Title: Re: Remove old wax?
Post by: Theo on February 15, 2011, 11:04:23 AM
Al, if there is a clean method I'd love to know it!  If the wax is old you get powdery dust everywhere,  if its fresh and soft it sticks to your fingers, tools etc.

Old dry wax might get less dusty if you warm the blocks carefully,  fresh wax gets less sticky when cold.   But the best method I've found is just to cover your work table with a sheet of newspaper, and wear an apron or overalls to protect your clothes.
Title: Re: Remove old wax?
Post by: Martyn on February 15, 2011, 11:05:05 AM
Now I'm sure there's a been a thread on this before but my searching has been in vain - so here's the question. I want to remove the old wax from a set of reedblocks and re-wax the reeds etc, but what's the best way of removing the old wax? Last time I did this I made a disgusting mess - surely there's a nice clean method of stripping the old wax off  ???
Regards
AL

I use an old blunt half inch chisel and use it over the bin......It works a treat for me.

Martyn
Title: Re: Remove old wax?
Post by: Alan Morley on February 15, 2011, 11:31:54 AM
Would a soldering iron work - possibly a daft suggestion....
Title: Re: Remove old wax?
Post by: old geezer on February 15, 2011, 11:50:24 AM
Would a soldering iron work - possibly a daft suggestion....

yep; your right
Title: Re: Remove old wax?
Post by: pete /acorn on February 15, 2011, 12:48:27 PM
Hi'
Would it not work if you put the blocks in a plastic bag then placed in freezer over night,the wax could become brittle and come off easily.
never tried it though.

Pete
Title: Re: Remove old wax?
Post by: rmenhinick on February 15, 2011, 01:07:10 PM
Would a soldering iron work - possibly a daft suggestion....

Maybe a hair-dryer/hot air gun used carefully to wark the old wax and then use a desoldering pump to suck out the molten wax?

I used to strip old circuit boards of valuable components by heating the solder with a hot air gun and then sucking away the molten solder using a vacuum cleaner with a reduced hose and an old metal pen tube.
Title: Re: Remove old wax?
Post by: LJC on February 15, 2011, 01:15:02 PM
A blunt old butter knife and lots of news paper works a treat for me. Just don't open the windows if there is even a breath of wind as this is a sure fire way to have the whole mess dumped on the carpet.
Title: Re: Remove old wax?
Post by: HallelujahAl on February 15, 2011, 01:51:04 PM
This is really helpful guys - thanks for all your advice. However, I fear I'll still be making a complete and utter mess again  ;D
Title: Re: Remove old wax?
Post by: Theo on February 15, 2011, 01:52:22 PM
A blunt old butter knife and lots of news paper works a treat for me.

I have one of those, but with the end cut off square which is very hand for getting into corners.

My other favourite tool for this job is a soft wire brush, either brass wire as used for suede shoes, or stainless steel wire which is available through the antiques trade for cleaning chemically softened paint by 'dip and strip' people.

This is really helpful guys - thanks for all your advice. However, I fear I'll still be making a complete and utter mess again  ;D

Its the only way!
Title: Re: Remove old wax?
Post by: Owen Woods on February 15, 2011, 02:12:14 PM
Now I'm sure there's a been a thread on this before but my searching has been in vain - so here's the question. I want to remove the old wax from a set of reedblocks and re-wax the reeds etc, but what's the best way of removing the old wax? Last time I did this I made a disgusting mess - surely there's a nice clean method of stripping the old wax off  ???
Regards
AL

I use an old blunt half inch chisel and use it over the bin......It works a treat for me.

Martyn

I use something similar, I found that CGM's bass pinger, which is I think supposed to be a shim works very well. Obviously you don't want to gouge the wood, so it leaves a very thin layer. This can be taken off easily with a suede shoe brush, which was a great tip from Theo. Works a treat. Doing it over the bin is important, otherwise it goes everywhere!
Title: Re: Remove old wax?
Post by: Lester on February 15, 2011, 03:20:11 PM
My weapon of choice is a metal 6" ruler.
Title: Re: Remove old wax?
Post by: forrest on February 15, 2011, 08:22:01 PM
I formerly used a  razor-sharp utility knife blade, and held it with edge flat as one would with a cabinet scraper, lots of paper underneath to catch the debris. Leaves a clean polished surface for re-waxing. Have since graduated to a small tool used for scraping paint, etc. from window glass. It uses a single edge razor blade and offers a much better grip for control. Also works well for trimming ends of leather or mylar valves when you get to installing them.
Title: Re: Remove old wax?
Post by: Stockaryd on August 17, 2017, 07:04:48 AM
This thread was useful.   (:)
Title: Re: Remove old wax?
Post by: Graham Spencer on August 17, 2017, 07:36:04 AM
I formerly used a  razor-sharp utility knife blade, and held it with edge flat as one would with a cabinet scraper, lots of paper underneath to catch the debris. Leaves a clean polished surface for re-waxing. Have since graduated to a small tool used for scraping paint, etc. from window glass. It uses a single edge razor blade and offers a much better grip for control. Also works well for trimming ends of leather or mylar valves when you get to installing them.

I use a scalpel with a fresh blade, used like a cabinet scraper as above. Works for me.

Graham
Title: Re: Remove old wax?
Post by: Steve_freereeder on August 17, 2017, 08:27:44 AM
Like Owen, I use one of Charlie's bass pinger (which I've found that I hardly actually use for its original purpose) to remove as much wax as I can.

I use something similar, I found that CGM's bass pinger, which is I think supposed to be a shim works very well. Obviously you don't want to gouge the wood, so it leaves a very thin layer. This can be taken off easily with a suede shoe brush, which was a great tip from Theo. Works a treat. Doing it over the bin is important, otherwise it goes everywhere!

I have sometimes then used a small cloth pad or cotton bud soaked in acetone to remove any residual wax film - although I'm not sure how necessary this is if I'm simply going to replace with fresh wax. 
Title: Re: Remove old wax?
Post by: Lester on August 17, 2017, 09:09:55 AM
I use a blade as a scraper, like GPS. Then once it's mostly clean I go over the block with a brass brush (suede brush (https://www.amazon.co.uk/d/Care-Products-Shoe-Accessories/Premium-Small-Brass-Woodern-Brush-Suede-Apparel/B008H3HW94/ref=sr_1_14?ie=UTF8&qid=1502957364&sr=8-14&keywords=suede+brush)) to remove all the remnants, then a going over with my industrial vac to remove any debris from the brushing.
Title: Re: Remove old wax?
Post by: Rob2Hook on August 17, 2017, 11:29:37 AM
My weapon of choice is a metal 6" ruler.

+1

Kinda substitute blunt chisel and cabinet scraper...

Rob.
Title: Re: Remove old wax?
Post by: Winston Smith on August 17, 2017, 11:40:18 AM
On the blocks which I've stripped, most of the wax has easily broken off with a thumb. The residue comes away with a Stanley knife blade dragged across the apertures from the base to the top, finishing off with a few strokes from a largish flat file, just to make sure that the surfaces are actually flat before refitting the reedplates.
Of course, it's messy; but who amongst us doesn't have a vacuum cleaner?
Title: Re: Remove old wax?
Post by: Nick Collis Bird on August 17, 2017, 05:17:39 PM
I leave it to Theo, Roger T or Martyn White. Then I have no problem at all  8)
Title: Re: Remove old wax?
Post by: John MacKenzie (Cugiok) on August 17, 2017, 06:23:26 PM
Surprised that nobody mentioned a 'Hot knife'. Not that I've ever done the job, but seems like it might work, to me.


Sir John

https://www.amazon.co.uk/s/ref=nb_sb_noss?url=node%3D262763011&field-keywords=Hot+knife&rh=n%3A262763011%2Ck%3AHot+knife
Title: Re: Remove old wax?
Post by: Lester on August 17, 2017, 06:25:25 PM
Surprised that nobody mentioned a 'Hot knife'. Not that I've ever done the job, but seems like it might work, to me.


Sir John

https://www.amazon.co.uk/s/ref=nb_sb_noss?url=node%3D262763011&field-keywords=Hot+knife&rh=n%3A262763011%2Ck%3AHot+knife

Just about the last thing I would use, nice old crispy wax or nice new flexible wax, easy to scrape off, hot runny wax will go everywhere.
Title: Re: Remove old wax?
Post by: Ebor_fiddler on August 17, 2017, 09:54:21 PM
Since I stopped smoking, I had no use for my pipe knife until I found it an ideal tool for de-waxing. So, you pays your money and you takes your choice.  :|glug
Title: Re: Remove old wax?
Post by: Stockaryd on August 17, 2017, 10:36:20 PM
Of course, it's messy; but who amongst us doesn't have a vacuum cleaner?

I have two. Robots crawling around on the floor.
Not often enough!     (:)   
But I understand what you all say.  No secrets,  just scrape! 
Title: Re: Remove old wax?
Post by: hickory-wind on August 18, 2017, 04:19:10 AM
Here are my weapons of choice left to right:
Simple scraper, highly modified steak knife (shortened and dulled), two clay sculpting tools.

The scraper spans the treble reedblock cavity so stays flat. The clay tools I just bought recently and I'm liking them. They are cheap and allow you to see both before and after the working area and don't get clogged like the scraper does often.
SimplePortal 2.3.5 © 2008-2012, SimplePortal