Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Harmonicatunes on March 05, 2011, 12:13:27 AM
-
Having decided that the famous Hohner button key travel is hampering my beginner's effort on my single row Hohner 1040, I've decided to do something about it.
From previous posts I've come across a photo essay by Theo on fixing button travel. It's located http://www.facebook.com/album.php?aid=109685&id=709188166 (http://www.facebook.com/album.php?aid=109685&id=709188166) I think even I could manage. And, if I mess it up, I can retrace my steps without lasting damage to the instrument.
Removing the bellows will be a first for me, however removing the four pins seems straightforward, hopefully likewise for getting them back in.
While my old 1040 bellows are off (almost certainly for the first time), it would make sense to replace the gasket. There is a previous post on this, at http://forum.melodeon.net/index.php/topic,1459.0.html (http://forum.melodeon.net/index.php/topic,1459.0.html). Are there any how to photos on gasket replacement, or is it obvious once the bellows are off.
Theo suggests using closed cell neoprene with self adhesive backing, and suggests that he could supply it. I'd be happy to take up the offer, to ensure I get the right stuff. Likewise with some leather washers for the keyboard screws.
Replacing pallet felts and valves would help, however as a first timer I wouldn't trust myself with the job.
-
From previous posts I've come across a photo essay by Theo on fixing button travel. It's located http://www.facebook.com/album.php?aid=109685&id=709188166 (http://www.facebook.com/album.php?aid=109685&id=709188166) I think even I could manage. And, if I mess it up, I can retrace my steps without lasting damage to the instrument.
You will be OK then ;D
Removing the bellows will be a first for me, however removing the four pins seems straightforward, hopefully likewise for getting them back in.
Yep
While my old 1040 bellows are off (almost certainly for the first time), it would make sense to replace the gasket. There is a previous post on this, at http://forum.melodeon.net/index.php/topic,1459.0.html (http://forum.melodeon.net/index.php/topic,1459.0.html). Are there any how to photos on gasket replacement, or is it obvious once the bellows are off.
Just peel off the old gasket and clean up any residual stuff then stick on the new gasket. Be careful when going around the corners not to stretch the gasket and, where the two ends meet, make sure to use an overlapping joint (cut the gasket at an angle on both ends so they overlap)
Theo suggests using closed cell neoprene with self adhesive backing, and suggests that he could supply it. I'd be happy to take up the offer, to ensure I get the right stuff.
Theo's your man for the tape.
Likewise with some leather washers for the keyboard screws.
Never need these myself
Replacing pallet felts and valves would help, however as a first timer I wouldn't trust myself with the job.
The pallet felt/leathers is fairly easy, get the necessary from Charlie Marshall (http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html#3). Valves are a whole new territory which will get you involved in tuning as changing the valves will normally change the tuning of the reeds.
Some possibly useful stuff HERE (https://picasaweb.google.com/lester.bailey/1140Refurbishment#)
-
Certainly doing pallets is not particularly difficult and quite satisfying (:) Good luck!
-
Thanks for posting the link to Theo's button travel mod. I've just done the same for my Double Ray, except I used PVA instead of screws and I put a layer of felt over the wood to stop the buttons clacking against the wood. Results have been satisfactory
-
Thanks for posting the link to Theo's button travel mod. I've just done the same for my Double Ray, except I used PVA instead of screws
Nooo! What happens if you need to make adjustments? What happens when the felt wears out? Even the wood will wear in time and need to be replaced. It only takes a very small extra effort to do a job properly!!!
-
I'm not that great with screws, and I was scared of going through the other side. It did need adjusting, but it was easy enough to get to to take the bit off that needed it. If I need to add more, it won't take much to stick something on top. If it needs replacing, I'm better at taking things apart, so give me some time with a saw, some sandpaper and a scalpel and I'll have it off. If I need to replace the felt, I'll rip it off and scrape off the remains. I'm sure it's not that far off taking felt and leather off the pallets.
-
Well, talk about making extra work!
I'm not that great with screws, and I was scared of going through the other side.
Is it difficult to measure the length of a screw to check it is less than the thickness of material it is is driven into?
Some time in the future, when this box gets to another technician, there will be curses on me for making information available which enables careless amateurs to do a botch job! I don't like that. I get satisfaction from doing the best repairs and modifications that I can, and in helping others to do likewise.
-
Theo,
I think you are coming down a little hard on him here. First of all, you can't hold yourself responsible for what people do with the information you share. Secondly, an honest mistake is not the same thing as carelessness. It is how we all learn. In this case the mistake is not evident until the next repair.
I for one have been very grateful for the information you have shared and I would not like to see you be afraid to share more in the future.
Michael
-
I'm not thinking of clamming up! It just saddens me when someone takes a "shortcut" because they don't like something as ordinary as woodscrews. Putting in a screw is a pretty basic skill, choose correct size of screw, drill pilot hole, drive screw home. If you can't master that should you be attempting to repair things that use screws?
-
It wasn't exactly a 'shortcut'. It was a conscious decision not to run the risk of punching a hole through the shell of my box.
-
Lester,
Could you please tell me what sort of glue you used to attach the pallets to the actuating arms?? Thanks.
-
Lester,
Could you please tell me what sort of glue you used to attach the pallets to the actuating arms?? Thanks.
I use a hot glue gun but would like to find an easier option. I have all sorts of problems with stopping the glue flowing once it starts and separating the glue on the pallet from the gun and ending up with miles of gossamer thing glue strands everywhere. This may just be my incompetence ;D
-
I've had good results using Titebond II; of course, I've no idea how difficult the pallets will be to remove when they next need attention........
(For those who are not familiar with it, Titebond II is an aliphatic resin glue widely used in the building of electric guitars & the like).
Graham
-
I've had good results using Titebond II; of course, I've no idea how difficult the pallets will be to remove when they next need attention........
(For those who are not familiar with it, Titebond II is an aliphatic resin glue widely used in the building of electric guitars & the like).
Graham
I will probably just try some of my favourite PVA (http://www.axminster.co.uk/polyten-pva-glue-prod22032/) next time.
-
Hohner used hide glue and a piece of cloth but it only lasts about 50 years. ;D
-
Lester,
Could you please tell me what sort of glue you used to attach the pallets to the actuating arms?? Thanks.
I use a hot glue gun but would like to find an easier option. I have all sorts of problems with stopping the glue flowing once it starts and separating the glue on the pallet from the gun and ending up with miles of gossamer thing glue strands everywhere. This may just be my incompetence ;D
Wax seems to be working well, it's a piece of cake to put on and even easier to adjust. It's used on my Saltarelle iirc and also on most PAs I think.