Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Christopher K. on March 09, 2011, 01:57:52 PM

Title: Pinning reeds onto leather gaskets
Post by: Christopher K. on March 09, 2011, 01:57:52 PM
As opposed to waxing, I was curious to see if anyone in the forum has tried pinning reeds onto new leather gaskets. What are the pros and cons of waxless reedblocks? Will it sound any different?
Title: Re: Pinning reeds onto leather gaskets
Post by: malcolmbebb on March 09, 2011, 03:18:43 PM
I have a concertina done this way- well, small brass screws - and it's fine. Had to adjust the position of a couple, and it wasn't hard.
I rather suspect that pins rather than screws would loosen over time.
Title: Re: Pinning reeds onto leather gaskets
Post by: Bill the Farmer on March 09, 2011, 03:28:49 PM
The one row melodeons built at EATMT, Stowmarket, and the ones to be built at South Thames College, both with Emmanuel Pariselle, later this year use this technique. I don't think it makes any difference to the sound, it makes it easy to remove or replace reeds, but you need to be dead eye dick with a Dremel to drill the holes for the screws in the reed chamber dividers. It's probably more work that waxing, as you have to slice up the gasket material, stick it on, trim it, drill the holes, place the reeds, drive in the screws, etc.
Title: Re: Pinning reeds onto leather gaskets
Post by: Lester on March 09, 2011, 03:34:49 PM
<snip> I don't think it makes any difference to the sound, it makes it easy to remove or replace reeds, </snip>

I not sure in my estimation whether it does in fact make it easier. Removing waxed in reeds only requires a quick poke with a blade and replacement a quick wizz round with a hot iron. Whereas the screws are usually shared with adjacent reeds so removing one reed disturbs the two adjacent ones, and the tightness of the screws can affect the tuning to the extent of stopping the reed sounding altogether (I saw this when Rees was tuning my Stowmarket 1 Row). The other problem is fixing the gasket so there are no air leaks which can be a right royal pain.

So I would stick to wax
Title: Re: Pinning reeds onto leather gaskets
Post by: george garside on March 09, 2011, 03:40:19 PM
I have a c1926  Excelsior  3 stop 1 row in A in which thhe reeds plates are both pinned & screwed, the pins being on  short side (top) end and the screws arranged midway down the sides so that the underside of the screw head retains 2 adjacent reedplates.

Thre are no reed chamber dividers protruding from the reedblocks i.e. the are flat topped with appropriate holes . The leather is one long strip per reedblock with holes to match.

I have always understood that reeds pinned on leather  was a bit on the posh side, being used on many top quality piano accordions &, rightly or wrongly, I have assumed thhat the leather is to insulate the vibration of the reeds from the reed block  so only the sound of the reed vibrating comes out the front?

george
Title: Re: Pinning reeds onto leather gaskets
Post by: Christopher K. on March 09, 2011, 11:36:28 PM
Seems that it was the practice before beeswax came into play, though I can't detect any noticeable difference in the tone. I have a Club circa 1939 with reeds pinned/screwed onto the blocks and a few battered old Hohners and East German boxes with this configuration.

I was interested because I thought the reed plates on a new piece of leather was rather attractive.  :|bl
SimplePortal 2.3.5 © 2008-2012, SimplePortal