Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: brianread on April 04, 2011, 12:51:08 PM

Title: Pokerwork refurbish - Result of re-felting pads
Post by: brianread on April 04, 2011, 12:51:08 PM
Ok, I've used some of charlie's dual layer felt to re-felt the pads on my pokerwork, but am now concerned about the resultant reduction in height the keys stick out from the keyboard.  I intend to use Theo's method of reducing the travel but I suspect that I need to recover some of the height I've lost by increasing the thickness of the felt/leather.  Two possiblities I can see:

1. Bend the metal on each key - danger of breaking it?
2. Cut the slot in the pad deeper so that the metal arm goes in further.

any thoughts?
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: Theo on April 04, 2011, 01:31:04 PM
Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: brianread on April 04, 2011, 02:04:26 PM
Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

excellent - thanks.
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: Martyn on April 05, 2011, 11:20:14 AM
Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 10mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Edited to add 10mm dot of linen.
 
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: brianread on April 05, 2011, 12:06:22 PM
Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 8mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Thanks Martyn, actually that is exactly what I am doing, although I could not have explained exactly why I thought it was best!
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: waltzman on April 05, 2011, 02:33:35 PM
Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 10mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Edited to add 10mm dot of linen.
 


Hide glue?
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: Martyn on April 05, 2011, 07:26:36 PM
Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 10mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Edited to add 10mm dot of linen.
 


Hide glue?


No, I tend to use pva. It saves keeping the glue pot going.  ;)

Martyn
www.melodeonrepairs.co.uk
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: brianread on April 30, 2011, 07:52:46 PM
Have now re-felted the bass end as well, and got rid of some of the clatter, but  I can see that the buttons still move inside the holes in the case, and therefore I presume I ought to felt line the holes as well.

Anyone got any pointers for this job?
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: brianread on May 09, 2011, 02:35:58 PM
Have now re-felted the bass end as well, and got rid of some of the clatter, but  I can see that the buttons still move inside the holes in the case, and therefore I presume I ought to felt line the holes as well.

Anyone got any pointers for this job?

aha - I see that this is called (by Theo) re-bushing (I think).  What felt should I use?
Title: Re: Pokerwork refurbish - Result of re-felting pads
Post by: Theo on May 09, 2011, 02:47:19 PM
Bushing cloth!

Its a woven material with a felted surface, as used in pianos and concertinas.
SimplePortal 2.3.5 © 2008-2012, SimplePortal