Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Flashman on July 01, 2011, 03:06:49 AM

Title: Split in bellows
Post by: Flashman on July 01, 2011, 03:06:49 AM
The bellows on my old hohner has a split on one of the folds if I get some bellows tape is it easy to easily repair this from the inside.  Its on the second or third fold from the fingerboard side.

Thanks in advance

Dazz
Title: Re: Split in bellows
Post by: Theo on July 01, 2011, 08:11:31 AM
If it is split right through the card you will need something stronger than bellows tape to reinforce it from inside as well as replacing tape on the outside.  A strip cut from a cereal box, folded lengthwise and glued into the damaged fold with pva will provide plenty of strength.  
Title: Re: Split in bellows
Post by: Theo on July 01, 2011, 08:31:08 AM

.. did you used to be on Blue Peter, Theo?  ::)

No, but I did watch Blue Peter.  ;)
Title: Re: Split in bellows
Post by: Rob2Hook on July 01, 2011, 10:34:49 AM
I know a guy who had a wire coathanger taped inside his bellows to stop it imploding!  Of course, he had a ribbon to hold the box closed as the straps no longer reached...  Eventually (about two years) he had new bellows made.

I was wondering whether it was feasible to replace the leather diamonds on otherwise OK bellows?

Rob.
Title: Re: Split in bellows
Post by: MartinW on July 03, 2011, 08:35:06 PM
If it is split right through the card you will need something stronger than bellows tape to reinforce it from inside as well as replacing tape on the outside.  A strip cut from a cereal box, folded lengthwise and glued into the damaged fold with pva will provide plenty of strength.

.. did you used to be on Blue Peter, Theo?  ::)

A complete digression, but I have played melodeon on Blue Peter.

Martin
Title: Re: Split in bellows
Post by: Peter Stormy Hyde on July 05, 2011, 12:01:17 PM
I know a guy who had a wire coathanger taped inside his bellows to stop it imploding!  Of course, he had a ribbon to hold the box closed as the straps no longer reached...  Eventually (about two years) he had new bellows made.

I was wondering whether it was feasible to replace the leather diamonds on otherwise OK bellows?

Rob.

Now this job takes a little patience as it can be a little fiddly.
Start off by stretching the bellows by using two timber diagonal braces within the bellows, try to get them to rest up against the frames.

Now you have to try and peel back the bellows tape without tearing it on the offending corners.

 I have a tool that I have made up so that I can slightly lift the metal corner,  sometimes you can take the corner right off without tearing the bellows board or fabric.

Then try and lift and fold back the bellows papers until all the diamond is exposed, some of the bellows makers used hide glue so with a bit of luck you might be able to lift them off without using moisture, but if all fails use a little water.

Replace the diamond with hide or rabbit skin glue, if you do not have that then PVA will service.

When it comes to gluing on the corner I use PVA Craft Glue, but contact adhesive will again service here.

Crimp the corner up with a parallel jawed pliers or use a small bull nose cutter (not to hard) as second best.

Best of luck
Peter
 

Title: Re: Split in bellows
Post by: Flashman on July 07, 2011, 02:26:34 AM
Cheers for the advice.  Took the bellows off and had a look on the inside found that the split is only on the coloured card and does not go all the way through if you know what I mean.
SimplePortal 2.3.5 © 2008-2012, SimplePortal