Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Just4Fun on September 01, 2011, 07:32:27 AM

Title: First project
Post by: Just4Fun on September 01, 2011, 07:32:27 AM
It was recently suggested to me that a good way to learn about those mysterious workings inside a box is to buy a bit of a 'project' from somewhere like ebay and open it up..... The question is; what sort of project would people advise? I would like to think that over time I could restore the beast to a state where it's actually something I want to pick up and play so, being a D/G player, should I be looking for a straight forward two row eight base or would it make even more sense to consider a one row? The other thing that occurs to me is that I should be looking for a make whereby getting hold of spares/bits and pieces isn't going to be too hard. Before you good folk inundate me with words of wisdom please keep in mind that if I do get something I'll be boring you all to death with 'so what do I do next' type questions for months to come!
Title: Re: First project
Post by: Tony M on September 01, 2011, 01:01:15 PM
An interesting question - which, I suspect, will have as many different answers as replies!

I suppose it's a balance - finding something is adequately good nick that it doesn't need a fortune spending on it, and paying sufficiently little that, if you really muck things up, you haven't spent a fortune on the learning process.

If I was looking for another project (and I'm not - I have plenty already!), I would look for something basically playable, with relatively good bellows - putting new bellows tape on is nice to do - you feel you've achieved something, it's not particularly difficult and it doesn't cost a lot, whereas having to replace the metal corners and/or the leather gussets is more fiddly (I've never had to do gussets yet), and repairing major damage (big splits, or collapsed folds on the back) might make replacement bellows a better bet - which gets more expensive.

As far as cleaning / re-waxing / re-valving goes, (which implies tuning afterwards, really), my advice would be to avoid anything with too many voices - it's fairly therapeutic doing the work, but if there is a huge number of reeds to do, it gets tedious and takes a long time (which, of course, is why a professional overhaul and tune isn't cheap).

There shouldn't be all that many bits that need "buying of spares" if you just want a playable end product - so long as it's basically all there to begin with.

Ultimately, therefore, it's up to you to figure out how much "difficulty" (or is it "challenge") you fancy.  You could always start with something cheap that only presents a small challenge then, bolstered by your success, take on something more interesting later.

See what wiser folk have to say (then make your own mind up - the important person to please is yourself, I think!)

All the best,

Tony M
Title: Re: First project
Post by: Theo on September 01, 2011, 01:13:33 PM
You should decide what is your main goal?  Is it learning or getting a playable instrument?

 If its learning I'd go with whatever I first found that was very cheap or free, but avoid 120 bass accordion - its just got too many componets and you will get bored after cleaning and valving the 100th reed plate.

If your main aim is to get a useful and playable instrument then follow Tony's advice, and make it a Hohner, most of the Saxony built instruments are poor things that are frustrating to work on and probably were not much good as players even when new, most are on a par with modern Chinese boxes.
Title: Re: First project
Post by: Just4Fun on September 01, 2011, 02:13:14 PM
Thank you both for your advice. I would really prefer something that is good to play at the end of it all. I think it would give me more of an incentive. So maybe a single row Hohner or summat... Early days yet and lots of thinking to do let alone actually finding something worth having a go at.
By the way Theo it was you that suggested this in the first place in Whitby. And the Erica is a winner, for which many thanks.
Please keep the advice coming and I'll keep you posted as the drama unfolds!
Title: Re: First project
Post by: Theo on September 01, 2011, 02:17:59 PM
If you go for a single row Hohner then I'd avoid the 4-stop as the reedblocks are not removable and access to the reeds on the sides of the blacks facing each other is very difficult.  The Hohner 1040 one row is a much better proposition.  The reeds are mounted flat, which makes them slightly more awkward to tune, but much easier to rewax than the 4 stop.

There is one of these on ebay now (http://www.ebay.co.uk/itm/300593042415) finishing later today.  I have no connection with the seller.
Title: Re: First project
Post by: Just4Fun on September 01, 2011, 04:07:00 PM
Thank you Theo. That might be an idea.
Title: Re: First project
Post by: Graham Spencer on September 01, 2011, 04:53:24 PM
That's on my watchlist, but Just4Fun's need is greater than mine - go for it. 

Graham
Title: Re: First project
Post by: Just4Fun on September 01, 2011, 09:44:14 PM
Thanks Graham. You're a gentleman. Unfortunately it went for more than I was happy to pay. Guess I'm about to become an eBay addict.
Title: Re: First project
Post by: Pete Dunk on September 01, 2011, 10:51:46 PM
Thanks Graham. You're a gentleman. Unfortunately it went for more than I was happy to pay. Guess I'm about to become an eBay addict.

You'll probably be disappointed more often than not then. I would have gone at least a fiver if not a tenner more on that and I might well have lost. This doesn't mean that one day you might not get lucky but don't hold your breath.

Pete.
Title: Re: First project
Post by: Just4Fun on September 01, 2011, 11:22:15 PM
Pete, I was tempted but I'm pig ignorant about the value of such things so I didn't want to get too carried away. Next time I'll probably pay twice what it's worth.
Title: Re: First project
Post by: Theo on September 01, 2011, 11:26:31 PM
It's also worth watching German ebay.  The Club IIB often goes quite cheaply.  If you are patient you should be able to get one for well under €100.  Here is an example
http://www.ebay.de/itm/Hohner-Club-II-B-Akkordeon-Diatonische-Handharmonika-/160645084955 (http://www.ebay.de/itm/Hohner-Club-II-B-Akkordeon-Diatonische-Handharmonika-/160645084955)

or this one is an older version of the same model

http://www.ebay.de/itm/Akkordeon-Hohner-Club-1b-Liebhaberstuck-sehr-alt-/300592948551 (http://www.ebay.de/itm/Akkordeon-Hohner-Club-1b-Liebhaberstuck-sehr-alt-/300592948551)
Title: Re: First project
Post by: Just4Fun on September 02, 2011, 05:32:14 PM
So here's a question to show my ignorance; Is there any difference between a 'Honer Club11b' and a 'Hohner Club 11b Victoria'? If so, should I rule out a 11b Victoria?
Title: Re: First project
Post by: Theo on September 02, 2011, 05:34:21 PM
As far as I ca tell the Club IIb is just a later version of the Club Victoria.  Two voice 30 button treble, 8 bass club system same or similar size case. Hohner's naming system is a complete mystery to me.
Title: Re: First project
Post by: Inventor on September 03, 2011, 12:53:27 PM
I have also seen many Club Melodeons go very cheaply on German eBay. Obviously Club System has gone out of fashion in Germany.  However with very few exceptions the sellers will only send to other parts of Germany, and usually demand other methods of payment than the reliable and guaranteed PayPal.  Does anyone know how to get round these problems ?
Inventor.
Title: Re: First project
Post by: Andy Simpson on September 03, 2011, 01:11:49 PM
Unless you have a friend in Germany there isn't any way around it. They're not obliged to post abroad, (it's a real hassle and I've stopped doing it on eBay), and Paypal is a nightmare for sellers so I don't blame the German eBay sellers at all for refusing to accept it. I only accept it because I'm forced to and always mention that I'd prefer an online bank transfer, a payment option that eBay mysteriously neglects to mention anywhere on the site.....

Title: Re: First project
Post by: Harmonicatunes on September 04, 2011, 02:01:40 AM
I would recommend the humble but sturdy Hohner single row 1040. They turn up regularly on eBay, usually in C. I have one in G and managed the keyboard travel restriction mod without drama.
Title: Re: First project
Post by: Just4Fun on September 04, 2011, 09:48:03 AM
Thanks again every one for your wisdom. I'm keeping my eye on eBay but I'm of to Bromyard in a few days and then The Gower for a week so it's not an ideal time to go chasing after things.
Harmonicatunes, I must admit that a single row in C is something I had alluded to already so your advice is doubly interesting. I'm trying hard to keep an open mind though, and to not treat this exercise as an excuse to indulge in more MAD.
Please keep the advice coming. It really is appreciated and when i do get hold of something I'll keep everyone posted as to the levels of destruction and despair that I manage to achieve!
Title: Re: First project
Post by: Owen Woods on September 04, 2011, 08:09:58 PM
My first project was(is) a 1140. It's a great box to start on, I've done everything bar tuning and it's sounding quite good otherwise.
Title: Re: First project
Post by: Lester on September 04, 2011, 08:48:39 PM
My first project was(is) a 1140. It's a great box to start on, I've done everything bar tuning and it's sounding quite good otherwise.

The only probem with an 1140 is when you come to he tuning as the reeds are flat mounted makng he access to the push reeds more difficult than normal and access to the pull reeds next to impossible for someone starting out. Boxes with removable reed blocks are much easier to tune for beginners (the group that I am struggling to emerge from (:) )
Title: Re: First project
Post by: Owen Woods on September 04, 2011, 09:47:31 PM
This is true. But then the instrument that you start tuning on is preferably one that you don't mind ruining utterly...
Title: Re: First project
Post by: nathanfisher on September 04, 2011, 10:55:11 PM
For my first project I decided to bid low on an old Hohner presswood 2 row.  I live in the US and there seems to be quite a few of those on Ebay. I managed to win the auction for a little over 100$ plus a reasonable shipping fee. You might be able to bid on something from the US and have it sent over to you? The exchange rate is definitely in your favor if the seller will ship international.
  The reeds turned out to be C/F so I will probably use those in the future to practice my tuning skills. The fingerboard is broken and will need to be replaced or fixed. The bellows are usable and the pads need new felt and leathers.  Surprisingly the presswood is a very solid wood box and the components are the same quality as a pokerwork or erica. From what I can tell it is made of solid Alder with the usual plywood soundboard. Pokerworks and Ericas sell for 2 to 4 times the price.

Most of the work I can do myself but I decided to buy some D/G reeds from Michael @ Dancemaster accordion. He loaded up a set of reeds on some old Hohner reedblocks and I installed  the reedblocks in the accordion myself. You wouldn't believe how good an old presswood can sound with good reeds in it. I have bought three accordions from Michael and I am very pleased with the work that he does.
http://www.irishdancemaster.com/accordion.html

Just my 2c in a sea of opinions!

Title: Re: First project
Post by: Just4Fun on September 04, 2011, 11:18:30 PM
So what are the more common boxes that have removable reed blocks? I feel that since I'm heading into this dark abyss I might as well go the whole hog and try to learn a bit about tuning as well.
Title: Re: First project
Post by: nathanfisher on September 05, 2011, 12:40:33 AM
Most accordions have removable reed blocks, except for the few that have the reedblocks permanently mounted onto the sound board like a one row cajun accordion or a Castagnary Lilly (just to name a few)

Here is a short video to show you how removable reed blocks are mounted onto the inside of an accordion!

http://www.youtube.com/watch?v=Ee1VSeALd6g&feature=related
Title: Re: First project
Post by: Andy Simpson on September 05, 2011, 01:18:48 AM

  The reeds turned out to be C/F so I will probably use those in the future to practice my tuning skills.


Oh no you won't!. 

Hohner reeds of that vintage are highly desirable and irreplaceable, they are far too good to be used for practice by a novice. It'd be like using an E-Type Jag in a demolition derby...
Title: Re: First project
Post by: nathanfisher on September 05, 2011, 02:31:32 AM
Irreplaceable? Yes! Highly desirable? The faces of the reedplates are tarnished, the reeds are riddled with rust and the person who tuned the reeds before me was not very kind.  If you insist then I will practice my tuning skills on a Chinese toy melodeon and sell you the c/f reeds if you think they are so valuable. (:)
Title: Re: First project
Post by: Just4Fun on September 23, 2011, 10:08:25 AM
Back from my travels and I've seen a "vintage" Hohner single row with two stops. I don't have a model number but it's got spoon type base and an anchor logo next to the 'Hohner' stamp. Does anyone know what it would be like to work on (assuming it needs it and it looks as though it would)? Just as a reminder, I'm a total beginner when it comes to maintenance etc. but wanting to learn.
Title: Re: First project
Post by: Rob2Hook on September 23, 2011, 06:20:04 PM
It could be a HA112 - just like a cajun four-stop, but with only two stops.  They're less frequently seen than the three and four-stop versions (HA113, HA114) and rarely used in performance, more of a home instrument.  They have all the characteristics of a four-stop, but being only two voice, MM, thye lack the grunt and bite of the full blown model.

Rob.
Title: Re: First project
Post by: Theo on September 23, 2011, 07:20:25 PM
As far as learning to repair it goes it has better access to the reeds than a Hohner 4-stop.  Reedblocks are not removable, but with only one block in this model you have full access to the reeds on both sides.
Title: Re: First project
Post by: Just4Fun on September 23, 2011, 10:32:32 PM
Thank you everyone for your wisdom. It might be a starter...
Title: Re: First project
Post by: Just4Fun on September 24, 2011, 05:56:48 PM
Well I got bored with trying to be grown up and sensible and have just got a Club 11b through eBay. I probably paid a bit over the odds for it but what the heck. Going by the photos it definitely has seen better days and according to the description "a couple of the notes sound a little low". No doubt, the full horror will become clear in due course. If people don't mind I'll do a couple of photos and a sound clip, post them on here and await your advice. Perhaps any work that I do could be posted here by way of a bit of a journal for future novices such as myself. Just to verify my total ignorance: I have heard people mention a mysterious phrase "I have de-clubbed it". Is this painful and is it something I should consider?
Title: Re: First project
Post by: Pete Dunk on September 24, 2011, 06:43:02 PM
Just to verify my total ignorance: I have heard people mention a mysterious phrase "I have de-clubbed it". Is this painful and is it something I should consider?

*Sharp intake of breath* Ignorance varified, no worries!  >:E

You'll need to find out what a Club box is first. Check out the keyboard layouts on the main site (http://forum.melodeon.net/index.php/page,keyboard_25_row.html).
Title: Re: First project
Post by: Graham Spencer on September 24, 2011, 06:43:52 PM
Well I got bored with trying to be grown up and sensible and have just got a Club 11b through eBay. I probably paid a bit over the odds for it but what the heck. Going by the photos it definitely has seen better days and according to the description "a couple of the notes sound a little low". No doubt, the full horror will become clear in due course. If people don't mind I'll do a couple of photos and a sound clip, post them on here and await your advice. Perhaps any work that I do could be posted here by way of a bit of a journal for future novices such as myself. Just to verify my total ignorance: I have heard people mention a mysterious phrase "I have de-clubbed it". Is this painful and is it something I should consider?

Ah, you bought that one.  I pulled out when it got to more than I was prepared to pay.  "De-clubbing" refers to changing the Club system layout to the conventional 2-row layout; in the Club system there is a button in the middle of the inner row that plays the same note in both directions (called a "gleichton"). The reasons for its being there need not concern us here, but if you want to play it as a conventional 2-and-a-half row that pair of reeds needs to be replaced by a pair playing the two notes you'd expect if it wasn't a Club. Hope I'm making myself clear - it's late, warm and humid where I am and it's been a long day!  Also, in an "ordinary" 2-row the inner row basses at the "knee" end play the same note & chord in both directions, whereas in a Club they don't. With my de-clubbed Hohner I decided to leave the basses as nature intended, as I rarely use that pair of buttons on the push anyway - some people prefer to de-club both ends.  In addition, the arrangement of notes on the "helper" row may or may not be what you expect, so you may decide to make some changes there. In my case, while I had the box in bits I decided rather than simply de-clubbing it to echo the layout on my Saltarelle with a 4th-button start, so that now the fingering for any given tune is exactly the same on the D/G Saltarelle or the Bb/Eb Hohner. I hope that makes some kind of sense.........

I should add that my Club is a Club II 21+4 - you have a longer helper row on a IIb, so more choices to consider!

Best of luck
Graham
Title: Re: First project
Post by: Just4Fun on September 24, 2011, 07:14:47 PM
Thank you Graham. I had a rough idea but you have described it brilliantly and now I have a very clear idea of what it is all about. Though not the foggiest yet about how it all works inside. In an ideal world I would expect I'd like to finish up with a layout similar to my Hascy which, I've actually had changed to a fourth button start, but no doubt those imaginings are rather far in the future. Obviously much depends on the state of the box when it arrives but a more realistic aspiration at this stage might be, for starters at least, to change the Gleichton. It's all got rather hot and humid here too but that's nothing to do with the climate and will no doubt get far worse when bellows pins start flying across the room.
I'll be back,
Ollie
Title: Re: First project
Post by: Pete Dunk on September 24, 2011, 07:29:09 PM
I have a Club IIIB that I recently de-Clubbed on the treble end, the bass end couldn't be altered as it had a clever mechanical arrangement to share reeds in the chords. If you do de-Club the treble end you might like to consider retaining the original gleichton reed plates and replacing them with donor reeds so that it can be re-clubbed if the fancy takes you.
Title: Re: First project
Post by: Just4Fun on September 24, 2011, 09:13:11 PM
So here starts the litany of questions that I will one day look back at and think 'oh gawd, I can't believe I asked them that'.
Reeds/Plates. Where do I get them and what should I be looking for? I would imagine it would need to be as per the others already being used.
Title: Re: First project
Post by: Pete Dunk on September 25, 2011, 12:32:00 AM
So here starts the litany of questions that I will one day look back at and think 'oh gawd, I can't believe I asked them that'.
Reeds/Plates. Where do I get them and what should I be looking for? I would imagine it would need to be as per the others already being used.

Therein lies a question! The donor reeds I used came from a scrapped piano accordion I bought for a tenner on ebay. They didn't really match the existing reed plates so the whole issue was more one of butchery, rather than any kind of scientific exercise. I was quite pleased with the outcome but I might just have been more than a little lucky!
Title: Re: First project
Post by: Graham Spencer on September 25, 2011, 06:27:10 AM
The ones I used to replace my gleichton plates also came from a scrap PA - a Hohner with H reeds which cost me £12 on ebay. I needed to replace my Bb/Bb with Bb/C, so I used the"B" reeds rom the PA, flattened one side to Bb and sharpened the other to C.  The reeds I needed to adjust the layout to match the Saltarelle came from another couple of scrap Hohners, a 2-voice C and a 4-voice G, both of which were well past saving (I paid £10 for the C at a flea market and £30 - probably too much really - for the G) so I had a reasonable supply of replacement Hohner reeds to hand. There are now a couple of T reeds in with the original H reeds in the Club, but they honestly don't sound any different and they are all Hohner. I make an occasional habit of picking up cheap past-repair boxes to cannibalise for parts - they do have to be really cheap - and have harvested a stock of replacement reeds this way.  Occasionally used reeds crop up on ebay.  You can buy new reeds from Charlie Marshall (or direct fron Hohner), but I quite enjoy dismantling otherwise useless old boxes; you get a lot of usable spares for not much outlay and you learn a lot about how the boxes work and how they were built.  Also good advice to hang on to the plates you take out - never throw usable reeds away!
Title: Re: First project
Post by: Just4Fun on September 25, 2011, 09:22:32 AM
Once again, really useful and much appreciated advice from everyone. The obvious first step is to take delivery of and find out the state of the box but I look forward to getting my hands dirty (Mr. Chinnery from The League of Gentleman comes to mind). I also look forward to searching for old wrecks and spares. I'll let you know when the thing arrives.
Ollie
Title: Re: First project
Post by: Graham Spencer on September 25, 2011, 11:07:13 AM
By chance there are two lots of Hohner PA reeds & blocks on ebay now; mind you, they're off a biggish box, and that would be an awful lot of unisonoric reeds to have lying around the workshop!
Title: Re: First project
Post by: Just4Fun on September 25, 2011, 11:40:48 AM
I saw those (one set of treble and one of base?) and was wondering if that would be a good place to start. Thanks Graham, you're a god send. How's the humidity?
Title: Re: First project
Post by: Lester on September 25, 2011, 11:55:06 AM
I saw those (one set of treble and one of base?) and was wondering if that would be a good place to start. Thanks Graham, you're a god send. How's the humidity?

You may be better off looking for a junker accordion which may well be cheaper than the reeds on eBay at the moment and will give you a host of other "useful stuff" like small screws, springs etc etc.
Title: Re: First project
Post by: Graham Spencer on September 25, 2011, 11:59:23 AM
I saw those (one set of treble and one of base?) and was wondering if that would be a good place to start. Thanks Graham, you're a god send. How's the humidity?

You may be better off looking for a junker accordion which may well be cheaper than the reeds on eBay at the moment and will give you a host of other "useful stuff" like small screws, springs etc etc.

I agree; there's a pretty little old Hohner Student for spares or repair on there at the moment, but I suspect it may be only single-voice.  The humidity's turned to torrential thunderstorms........

Graham
Title: Re: First project
Post by: Just4Fun on September 25, 2011, 12:18:39 PM
Ahha, so would I be right in thinking that a wreck of a thumping great Hohner PA would be a good start? Again, thank you everyone for you guidance.
Title: Re: First project
Post by: Lester on September 25, 2011, 12:21:19 PM
Ahha, so would I be right in thinking that a wreck of a thumping great Hohner PA would be a good start? Again, thank you everyone for you guidance.

Wrecking a big accordion is always a good start, for almost anything  >:E

But yes it will be full of project goodness
Title: Re: First project
Post by: Just4Fun on September 25, 2011, 04:21:28 PM
Thanks Lester. Besides, I always enjoyed Jeux Sans Frontieres!
Title: Re: First project
Post by: Just4Fun on September 27, 2011, 09:01:18 AM
Still on the hunt for a spares source. Quick question; Do the parts on different club models tend to be interchangeable? In other words could I use bits from a club 111 or 1 to redo a club 11?
Title: Re: First project
Post by: Graham Spencer on September 27, 2011, 09:27:59 AM
Depends on which bits you have in mind.......
Title: Re: First project
Post by: Just4Fun on September 27, 2011, 02:19:35 PM
I was thinking mainly along the lines of valves and reeds with anything else being a bit of a bonus.......
Title: Re: First project
Post by: Theo on September 27, 2011, 02:28:01 PM
Reeds, yes pretty much interchangeable, but reed blocks may not be.

Valves?  Here we have to be careful of terminology. In the UK valves are the flaps of leather or plastic to stop air going backwards through the non playing reed.  These should always be replaced with new if they are not working. 

Elsewhere 'valve' ('valvole' in Italian) are the felt/leather lined wood, metal or hard plastic things that open to allow air to sound a reed when you press a button.    In the UK these are called 'pallets'.  These are often interchangeable, but come in different sizes for 2 or 3 voice boxes.  The wooden ones are easily made if you need to replace the odd one.
Title: Re: First project
Post by: Graham Spencer on September 27, 2011, 02:43:40 PM
In any case, I would replace valves (UK terminology) with new ones as a matter of course if doing a fair amount of surgery in the reed department. They're cheap and easily available.
Title: Re: First project
Post by: Just4Fun on September 27, 2011, 02:59:00 PM
I've got the opportunity of getting hold of a moderately knackered club 1 for a fair (not bargain) price so I'm wondering about doing that and either using parts from the club two that's on its way to me, or visa versa, plus sourcing other bits and pieces as necessary and finishing up with a descent club 1 or club 11 depending on which way I go. Is this a mad and unworkable proposition? trying not to leap before I can jump!
Title: Re: First project
Post by: Theo on September 27, 2011, 04:32:15 PM
Hard to advise without seeing the two boxes.  Thinking of what might need to be replaced the most likely is a broken reed or two.  Having another box in the same tuning would be a great help there.  Broken bass buttons are another frequent need for parts.  Most of the rest is either 'consumables' - felt, leather, valves, wax or woodwork.

You do seem to be in danger of acquiring a serious case of MAD.
Title: Re: First project
Post by: Just4Fun on September 27, 2011, 05:11:33 PM
That was diagnosed a long time ago. But I'm retired and it keeps me from far worse sins! Thanks Theo for your help.
Title: Re: First project
Post by: Rob2Hook on September 28, 2011, 05:04:48 PM
I have a Club I and a Club II which are almost identical apart from the grille on one is celluloid and metal on the other.  The only other difference is that the octave break on the basses is different.  I haven't directly compared the reed blocks, though.

Rob.
Title: Re: First project
Post by: Just4Fun on October 20, 2011, 11:25:52 PM
I've now acquired a very battered club 11 and a 111M which is actually in pretty OKish nick. One of the first jobs I'm looking at (scary) is limiting the travel on the treble side. I've had a bit of a trawl through 'construction and repair' and found reference to a photo journal by Theo but the link no longer seems to be working. Are there any rules to follow or should I just get in there and wield my axe?
 Also, the box comes complete with classic Hohner discoloured yellow buttons and I get the impression that my best bet would probably be to just replace them rather than spend days grinding and polishing. Again, Any comments?
 I'll post some photos in due course.
Title: Re: First project
Post by: Theo on October 21, 2011, 09:01:49 AM
Limiting the treble action is easier on Clubs because the fingerboard can be take apart.  So its a simple matter to place the appropriate thickness of felt under the buttons. 
Title: Re: First project
Post by: Just4Fun on October 21, 2011, 09:26:49 AM
Thank you Theo, I'll get some felt then. There are various interesting creaks, squeaks and groans going on so I'll see the full horrors when I start taking it to bits. Planning on taking plenty of photos to give myself a half chance of sticking it back together again!
Title: Re: First project
Post by: Theo on October 21, 2011, 10:11:51 AM
Havwe fun.  Like all Hohners they are well built and everything should come apart and go back together without any really difficult problems.  Severe moisture damage is about the only thing that might defeat you.
Title: Re: First project
Post by: Just4Fun on October 25, 2011, 12:08:52 PM
And what fun it is. Flying in the face of adversity I've actually replaced a bellows strap! Time for a lie down in a darkened room!.
I've also taken some photos and removed some bits in preparation for having a go at limiting the action and also to see what state things are in. My inexperienced eye says that things don't look too bad but I would really appreciate the opinion of those who know what they're doing. To that end I've attached some photos and look forward to your comments.....
Title: Re: First project
Post by: Theo on October 25, 2011, 01:08:38 PM
Also, the box comes complete with classic Hohner discoloured yellow buttons and I get the impression that my best bet would probably be to just replace them rather than spend days grinding and polishing. Again, Any comments?

These buttons look almost new, some Club IIIMs seem to have had buttons which were a yellowish colour from new.
Title: Re: First project
Post by: Just4Fun on October 25, 2011, 01:16:00 PM
They say a camera never lies but in this case the true yellowness hasn't shone through! Mind you, I've got a 11b which I'm using for spares and bits n pieces and the buttons on that are yellower than you could imagine.
Title: Re: First project
Post by: Just4Fun on October 27, 2011, 10:00:22 PM
Update time.

I've limited the action which has made a surprising difference (beneficial) and put it back together again just to reassure myself that I could! It's actually rather a nice box to play so rather than almost certainly ruining it by trying my first tuning job on it I'm going to get Martyn White to do his magic on it and play around at tuning a complete wreck (yet to be found) instead. But I will do other bits and pieces to the Club 111 such as bellows tape, resurfacing pallets etc.

Meanwhile I've been trying to gather some of the necessary tools. Good old Melnet has been invaluable in this regard.

All in all, thus far, it's not been quite as scary as I thought it might have been though It'll be a long time before I start taking my Hascy to bits!
Further updates to follow......
SimplePortal 2.3.5 © 2008-2012, SimplePortal