Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Martyn on September 24, 2011, 11:42:37 AM

Title: Reed Wax
Post by: Martyn on September 24, 2011, 11:42:37 AM
I usually buy my reed wax ready made but I thought I would have a go at making my own.

Everything seemed to go to plan in the manufacturing process but when I tried to use it with the soldering iron at my normal setting the wax tended to spit and spatter and I can't work out why.

I was very careful not to get any moisture in the mix and the beeswax was of the purest quality from a beekeeper. I used a powdered rosin bought online from a specialist and the oil I used was olive.

The ratio was beeswax 60%,  rosin 40% the quantity was enough to three quarters fill a 500g margarine tub, I then added about half a 35mm film pot of olive oil.

Any ideas please?   ???

Martyn
  
Title: Re: Reed Wax
Post by: diatonix on September 24, 2011, 12:03:51 PM
 Occasionally this also happens with Italian wax. It's not really a big deal. Before using it, just let it simmer a while at a not too high temperature until it stops spitting & spattering.
Title: Re: Reed Wax
Post by: Theo on September 24, 2011, 12:20:25 PM
It can be caused by undisolved particles of rosin in the wax.
Title: Re: Reed Wax
Post by: Martyn on September 24, 2011, 12:34:55 PM
It can be caused by undisolved particles of rosin in the wax.

I made sure the rosin was completely melted in a separate vessel before adding the molten wax to it. Then letting the whole lot simmer away together for another 20 minutes to make sure. Are the ratios about right and does it need a bit more oil?

Martyn
Title: Re: Reed Wax
Post by: rees on September 24, 2011, 01:57:55 PM
The ratios sound about right Martyn.

I think I've posted this before but here it is again.
A very old accordion tuner in Castelfidardo once gave me the following recipe:

50% wax, 50% rosin and 5% olive oil.

105% - turbo reed wax!
Title: Re: Reed Wax
Post by: Don Roberts on September 26, 2011, 12:06:11 PM
and while on the subject of reed wax, is it advisable to re use old wax, given it doesn't appear to be too old and dry ?
Title: Re: Reed Wax
Post by: Martyn on September 26, 2011, 12:27:41 PM
and while on the subject of reed wax, is it advisable to re use old wax, given it doesn't appear to be too old and dry ?

Personally I would never re-melt the old wax, even if it looks ok. Far better to clean off the old wax and use new.

Martyn
Title: Re: Reed Wax
Post by: Theo on September 26, 2011, 01:56:25 PM
As well as the old wax being an unknown quantity in terms if its fitness for use, it is much easier to make a neat job of the waxing if starting with fresh wax and everything clean.
Title: Re: Reed Wax
Post by: blafleur on September 26, 2011, 02:12:25 PM
Also on the subject of reed wax, I, being the consummate do-it-yourselfer, also had a burning desire to make my own wax, with the comments of Theo that it's usually not worth it in the back of my mind.  But I did it, bought some highly refined bees wax, resin, and concocted the witches brew, made a big mess, and got some pretty decent wax that ended up costing me about what the wax I usually bought did.  Now that that's out of my system, I'll probably go back to buying wax and making other things.

Bryan Lafleur
Title: Re: Reed Wax
Post by: ker42 on October 06, 2011, 06:53:30 PM
If I may jump on-board the 'reed wax' inquiries...      Newbie mistake  :|bl   First re-waxing of bass reed pans, without remembering to put the growl box back on first. ...so, now I need to remove said, fresh, fully-functioning reed wax (two of the four screws are located behind the reed pans ::) )   So, before I just go about scraping and picking, I was just curious if there was a betterer way to go about this, that I am not aware of.    Why re-invent the wheel, ya know!  ;)
Title: Re: Reed Wax
Post by: Lester on October 06, 2011, 06:58:58 PM
If I may jump on-board the 'reed wax' inquiries...      Newbie mistake  :|bl   First re-waxing of bass reed pans, without remembering to put the growl box back on first. ...so, now I need to remove said, fresh, fully-functioning reed wax (two of the four screws are located behind the reed pans ::) )   So, before I just go about scraping and picking, I was just curious if there was a betterer way to go about this, that I am not aware of.    Why re-invent the wheel, ya know!  ;)

I would just pop the reeds out of the wax, useing a scapel to slide under the reed and pop it up, insert the screws then reseat the reeds and run my waxing (soldering) iron around the reed to reflow the wax.
Title: Re: Reed Wax
Post by: ker42 on October 06, 2011, 08:24:32 PM
AH, yes....the old "common sense" approach, I see  8)    Why is it we one can never see the forest for the trees?  :D
Title: Re: Reed Wax
Post by: Kimric Smythe on February 26, 2012, 08:22:14 AM
 Interesting to hear you folks use olive oil in your wax. People on this side of the pond use linseed oil. I add a bit of Castor oil to get it to stick a bit better, has good temp stability too. You can use a lamp dimmer on your soldering iron to get some temperature control, stops it from smoking so much.
SimplePortal 2.3.5 © 2008-2012, SimplePortal