Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: nomad on December 14, 2011, 01:09:43 PM

Title: Removing surface scratches from celluloid
Post by: nomad on December 14, 2011, 01:09:43 PM
Hi

I have a black accordion and some scratches have appeared on it. Rather than just jump in head first and get the Tcut out, I would welcome any advise as how to polish out the scratches. They are not very deep but just slightly deeper than surface marks.
in the past I have used a car polish for cleaning my box, someone also mentioned using brasso? 
What are your thoughts?
Thanks
Title: Re: Removing surface scratches from celluloid
Post by: Martyn on December 14, 2011, 04:00:44 PM
I always use Liberon burnishing compound for generally cleaning up the celluloid. If a bit more 'cut' is needed to remove light scuffs and scratches I will use T-Cut. For the slightly deeper marks I will use a rubbing compound that is used for flattening and leveling car paint.
This will leave a matt finish and will need the shine brought back again with T-Cut.  
                                                                                                              
Generally speaking though, if the scratch is deep enough for you to feel when you run a thumb nail over it, it will be very hard to remove, if not impossible.
                         :Ph

Martyn  
Title: Re: Removing surface scratches from celluloid
Post by: nomad on December 14, 2011, 04:57:24 PM
Hi Martyn

Yes I can feel it slightly when I run my thumb nail over it.  Wasn't sure if you could build it up with paint then polish it down.

Title: Re: Removing surface scratches from celluloid
Post by: Martyn on December 14, 2011, 07:42:01 PM
Hi Martyn

Yes I can feel it slightly when I run my thumb nail over it.  Wasn't sure if you could build it up with paint then polish it down.



Not sure if that would work too well. It might be worth a try in an inconspicuous area but once it was built up enough would need to be cut back with wet and dry and then burnished.

Martyn
Title: Re: Removing surface scratches from celluloid
Post by: mory on December 14, 2011, 07:52:02 PM
A word of caution with putting paint on the plastic (sic) coating of your box some paints can have dramatically damaging affects on the finish of your box and it can travel unabated even if your trying to wipe it off as it travels through the coating itself All the Best mory
Title: Re: Removing surface scratches from celluloid
Post by: savantuk on December 15, 2011, 12:04:06 AM
I once had a red Erica which I dropped down the steps of Whitby market.

I made a very effective (and all but invisible) repair by using red ski wax.  I just dripped it into the scratches using a soldering iron, and scraped them level with a Stanley knife before it hardened.  I polished the repairs with T cut, and then with guitar burnishing cream.  It polished beautifully.

Ski wax is a very hard and very tough wax which is applied to the soles of ski's.  I've often felt is is more of a plastic than a wax, but it does do the job.  If it will fill holes in ski's, then it will fill holes in cellulid.

Good luck.

Doug
Title: Re: Removing surface scratches from celluloid
Post by: Christopher K. on December 15, 2011, 03:13:51 AM
I always use Liberon burnishing compound for generally cleaning up the celluloid. If a bit more 'cut' is needed to remove light scuffs and scratches I will use T-Cut. For the slightly deeper marks I will use a rubbing compound that is used for flattening and leveling car paint.
This will leave a matt finish and will need the shine brought back again with T-Cut ...

Martyn  

Martyn, does the rubbing compound work well for celluloid that has become cloudy or stained-looking with age? If it's a rubbing compound, it would take off a very thin layer from the top, right? I have a few old celluloid boxes that have brown patches where they've been played or exposed to dirt for so long and I'd love to bring back their true color. I'm wondering if this might do the trick.
Title: Re: Removing surface scratches from celluloid
Post by: Martyn on December 15, 2011, 09:51:10 AM
I always use Liberon burnishing compound for generally cleaning up the celluloid. If a bit more 'cut' is needed to remove light scuffs and scratches I will use T-Cut. For the slightly deeper marks I will use a rubbing compound that is used for flattening and leveling car paint.
This will leave a matt finish and will need the shine brought back again with T-Cut ...

Martyn  

Martyn, does the rubbing compound work well for celluloid that has become cloudy or stained-looking with age? If it's a rubbing compound, it would take off a very thin layer from the top, right? I have a few old celluloid boxes that have brown patches where they've been played or exposed to dirt for so long and I'd love to bring back their true color. I'm wondering if this might do the trick.

The various rubbing compounds or burnishing creams will not restore faded or stained celluloid as this almost certainly goes right through. It will just make them shinier. 8) Although T-Cut will remove surface staining.

Martyn
Title: Re: Removing surface scratches from celluloid
Post by: Mike Averill on December 15, 2011, 06:49:44 PM
If you want to fill scratches or build up on celluloid finished boxes use nail polish. Its the liquid form of the same stuff and comes in a vast array of colours making a good match easy.
Title: Re: Removing surface scratches from celluloid
Post by: Theo on December 15, 2011, 06:53:40 PM
Its the liquid form of the same stuff

So it will solvent weld itself to the celluloid and any repairs done this way will be permanent.  Take great care not to let it come into contact with the celluloid anywhere else because it will damage the surface.   Allow plenty of drying time for all the solvent to evaporate before attempting to polish.  I suggest 24 hours in a warm room.
Title: Re: Removing surface scratches from celluloid
Post by: nomad on December 15, 2011, 06:57:52 PM
Hi, thanks for information, I will try the nail polish, and will use tape to protect the surfaces around the scratch

Title: Re: Removing surface scratches from celluloid
Post by: Kimric Smythe on December 20, 2011, 04:55:50 AM
Clean out the scratch first so you don't trap dirt under your repair.
 Apply the nail polish with a tooth pick to the scratch, you may need several applications for deep scratches.
 Don't rush it, you need to wait about 24 hrs between applications or you will get bubbles. Let dry for about a week, put 3000 grit wet/dry sand paper on a small piece of wood (you need to make a tiny sanding block) dab some water on the place to be sanded. You will need to sand down any nail polish that stands above the surface of the celluloid. Keep the sand paper wet or it will clog.
 Finish up with auto paint scratch remover and then  auto paint polish (not wax). This will take awhile.

White mother of pearl celluloid is tricky as it is a transparent pearl finish over a solid white celluloid backing. You will need to duplicate this to do a professional repair.
SimplePortal 2.3.5 © 2008-2012, SimplePortal