Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Prestidigitator on February 26, 2012, 02:52:44 PM

Title: Irons - my latest acquisition
Post by: Prestidigitator on February 26, 2012, 02:52:44 PM
We had some discussion a while back about the Hobbycraft encaustic wax tool's suitability for reed waxing - so I got one.

I was being dragged round an Lidl store today, and noticed an electric "wood burning iron" i.e. pyrography tool, at £8.99 (rather less than the Hobbycraft tool, as I recall). The Lidl iron comes with 7 detachable bits for drawing, which look as if they will do for waxing. As these curiosities in Lidl seldom appear twice, I bought one, on the spur of the moment.
It also has 7 small branding irons with tasteful designs upon each; so if it doesn't work as a waxing iron, I can always amuse myself by turning my horrible plain old French and Italian boxes into "pokerworks".

I expect to be doing some reed repairs soon, so I'll report on how it worked.
Title: Re: Irons - my latest acquisition
Post by: Steve_freereeder on February 26, 2012, 03:27:50 PM
I have a feeling the pyrography irons may be too hot for reed wax.

I use a soldering iron with a variable temperature control and digital display. I notice that the reed wax melts cleanly without smoking on a setting of 180 to 190°C, which I suspect is quite a bit cooler than the temperature required to char wood.
Title: Re: Irons - my latest acquisition
Post by: diatonix on February 26, 2012, 04:13:03 PM
Waxing reeds with soldering irons or similar tools is problematic and should be avoided, especially when waxing whole reed blocks.
By using either a German or an Italian type waxing spoon that can be dipped into a melting pot you will get a more professional result in much less time. It will allow you to hold the reed block with one hand. By exploiting the forces of gravity and with some experience the molten wax will float freely wherever you want it to go (and can be more easily prevented from floating where it is not supposed to go).
Title: Re: Irons - my latest acquisition
Post by: Prestidigitator on February 26, 2012, 05:52:40 PM
I have a feeling the pyrography irons may be too hot for reed wax.

I use a soldering iron with a variable temperature control and digital display. I notice that the reed wax melts cleanly without smoking on a setting of 180 to 190°C, which I suspect is quite a bit cooler than the temperature required to char wood.

Steve-I had planned to use the dimmer switch which I use with my ordinary soldering iron, and the Hobbycraft tool, to get it to the right temperature.  As you point out, charring wood means plenty of heat, and this gadget says "Max Working Temperature 550°C", so it will certainly need cranking down. I don't plan to do pokerwork on the reed blocks. I'm also looking at getting a variable iron "station", I guess
like yours, as it seems that the prices for fairly basic systems from people like Maplins are now far more reasonable.

Diatonix - I do indeed have several waxing spoons in different sizes which I made myself. Although I like them, for all the reasons you give, I use them rarely, as I don't generally have that much waxing to do at one go and find that cranking up the double-boiler, melting enough wax to "work" the spoon properly and so forth is a bit much for small repairs. At the moment, as part of a learning curve, I'm reinstating some Preciosa reeds (for practice, mainly), and I'm casting around for methods and tools that I'm comfortable with, and which do the job properly. These will include a "small spoon" trial.

At least I know that whatever mess I make (within reason), there is some salvation from the professionals - to whom I should probably have entrusted the work in the first place, as I generally do. Still, "Nothing Ventured, Nothing Gained".
Title: Re: Irons - my latest acquisition
Post by: Theo on February 26, 2012, 10:54:58 PM
Waxing reeds with soldering irons or similar tools is problematic and should be avoided, especially when waxing whole reed blocks.

That is rather a sweeping statement.

I must have waxed 100s of whole reed blocks with a temperature controlled soldering iron and I find it a quick and convenient method.  I've done a set of two treble blocks this evening from a Hohner Double Ray. The waxing process took just over 15 minutes for the 42 reed plates.  I'll post a photo tomorrow to demonstrate the neatness of the job.
Title: Re: Irons - my latest acquisition
Post by: Owen Woods on February 27, 2012, 12:00:37 AM
I think that the method used to wax in reeds is something of a personal preference. There are doubtless lots of ways of doing it and I've seen exceptional results from many. I can vouch that Theo's waxing is extremely neat.
Title: Re: Irons - my latest acquisition
Post by: Theo on February 27, 2012, 12:11:48 AM
Thanks for that!  I suspect I would make a pretty good mess with the traditional waxing spatula until I had plenty of practice.
Title: Re: Irons - my latest acquisition
Post by: Steve_freereeder on February 27, 2012, 01:06:27 AM
I can vouch that Theo's waxing is extremely neat.
Hear, hear!  (:) :|glug
Title: Re: Irons - my latest acquisition
Post by: Theo on February 27, 2012, 08:03:28 AM
Exhibit A m'Lud, and I have done no tidying up of the wax after it cooled.   Valves were fixed before waxing.
Title: Re: Irons - my latest acquisition
Post by: Quebecois on February 27, 2012, 03:13:54 PM
I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and various other repairs, and it worked like a charm. Cost me only CAD $27 in a craft store. The tip is slotted, which makes it really easy to use with wax sticks; it works a bit like an old ink pen, wax flows through the slot and then exits through the tip exactly where you want it.
Title: Re: Irons - my latest acquisition
Post by: Prestidigitator on February 28, 2012, 06:51:36 AM
I find that my dimmer switch will control the temperature of my new "wood burning iron" from stone-cold to red-hot, so some practical testing will shortly begin.

I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and various other repairs, and it worked like a charm. Cost me only CAD $27 in a craft store. The tip is slotted, which makes it really easy to use with wax sticks; it works a bit like an old ink pen, wax flows through the slot and then exits through the tip exactly where you want it.

That's given me an idea about a better way to use my encaustic wax pen/stylus; for which, thanks.
Title: Re: Irons - my latest acquisition
Post by: forrest on February 29, 2012, 08:09:54 PM
I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and various other repairs, and it worked like a charm. Cost me only CAD $27 in a craft store. The tip is slotted, which makes it really easy to use with wax sticks; it works a bit like an old ink pen, wax flows through the slot and then exits through the tip exactly where you want it.

Wow, I'd like to find out more about this. In a former lifetime, I was a draftsman and actually drew lines with the old style 'ruling pens' on linen media. I like the idea (in theory anyway) of distributing wax this way, if the tool is not too bulky!

Title: Re: Irons - my latest acquisition
Post by: Owen Woods on March 01, 2012, 12:49:54 AM
I wrote a long post about the merits of using an encaustic stylus but now can't find it :( But there are posts available if you are interested.
Title: Re: Irons - my latest acquisition
Post by: Prestidigitator on March 01, 2012, 07:59:45 AM
I wrote a long post about the merits of using an encaustic stylus but now can't find it :( But there are posts available if you are interested.

Would this be it?

http://forum.melodeon.net/index.php/topic,6971.0.html (http://forum.melodeon.net/index.php/topic,6971.0.html)
Title: Re: Irons - my latest acquisition
Post by: Quebecois on March 01, 2012, 12:26:20 PM
I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and various other repairs, and it worked like a charm. Cost me only CAD $27 in a craft store. The tip is slotted, which makes it really easy to use with wax sticks; it works a bit like an old ink pen, wax flows through the slot and then exits through the tip exactly where you want it.

Wow, I'd like to find out more about this. In a former lifetime, I was a draftsman and actually drew lines with the old style 'ruling pens' on linen media. I like the idea (in theory anyway) of distributing wax this way, if the tool is not too bulky!
Kandi Hot Wax Stylus
http://www.i-kandi.com/HotWaxArt-Encaustic-Stylus.asp
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 02, 2012, 09:57:43 PM
Exhibit A m'Lud, and I have done no tidying up of the wax after it cooled.   Valves were fixed before waxing.

Theo, do you have any photos of your tools and/or process of waxing that you can share with us? I'd really like a cleaner process than I'm using right now.

Thanks
Title: Re: Irons - my latest acquisition
Post by: Theo on March 04, 2012, 11:02:11 AM
Exhibit A m'Lud, and I have done no tidying up of the wax after it cooled.   Valves were fixed before waxing.

Theo, do you have any photos of your tools and/or process of waxing that you can share with us? I'd really like a cleaner process than I'm using right now.

Thanks

I don't have any photos,  its something I need to do.  I've not done it so far because the processes mostly need two hands so I need someone to operate the camera.   The things you need to see are are quite small, and with two hands, my head, and a fume extractor all close together its not a simple matter to photograph.   So it is something I would like to do, but it may not get done very soon.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 05, 2012, 04:09:57 AM
I read up on using a soldering iron for waxing reeds today. I wrapped some 12 gage copper electric wire around my soldering iron, flattened the end to a spatula shape and put a curve in the spatula. It works quite well though it's slow in the execution. It took quite a while to get used to the process but I did end up with a much cleaner wax job than I ever have before. I don't know how I'd do the Preciosa reeds since there's no space between one reed and the next, but that's for another day.

Theo, a photo of your "waxing iron" would help me a great deal at this point. Forget about trying to do a video. Having done a full melodeon today, I realize how difficult it would be to do a video. A photo or two of the tool(s) would be great though.

Thanks.
Title: Re: Irons - my latest acquisition
Post by: Theo on March 05, 2012, 08:18:19 AM
The tool is just an unmodified small temperature controlled soldering iron. I rest a stick of wax against the side and it melts and runs off the tip. 
Title: Re: Irons - my latest acquisition
Post by: forrest on March 05, 2012, 04:58:13 PM
  Regulating the heat seems quite as important as well...you need the iron hot enough to liquefy the wax so it flows well and gets good adhesion to the surfaces, but not so hot as to scorch the wax, and vaporize the more volatile components, which are there mainly to preserve the tenacity and pliability of the wax. Sounds like Steve has found a good type of iron for precise control.
   I think this reason alone is enough to justify the the wax stick and iron method; otherwise, you are cooking a small pot of wax over a flame, evaporating your constituents, dipping in with a spoon, and although the results of the waxing job may be first rate, your remaining wax in the pot has been compromised to some degree. I'll also admit I was a bust with the old-style waxing spoon! :|bl
Title: Re: Irons - my latest acquisition
Post by: Steve_freereeder on March 05, 2012, 05:37:54 PM
Sounds like Steve has found a good type of iron for precise control.
This is what I use. It's a Precision Gold soldering iron and station, from Maplin.
There is a photo of it on Amazon here (http://www.amazon.co.uk/PROFESSIONAL-STATION-ADJUSTABLE-SOLDERING-TEMPERATURE/dp/B0025UOAP4), although I note that Amazon have marked it as currently out of stock. Should be available from Maplin direct though.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 05, 2012, 05:49:53 PM
This is what I use....

Thanks Steve. Do you use the standard soldering tip or something different - a blade tip of some kind?

I started waxing with Charlie Marshall's brushing technique but found the wax cooled too quickly resulting in the brush getting stuck to the reed frequently. Plus the drips that seemed to happen in the wrong places necessitating later cleanup.

I've tried the spoon method and have found it difficult to get a clean distribution of the wax. Too many possibilities for dripping the wax where you don't want it. I've seen video demonstrations of a professional working with a spoon but it hasn't worked out well for me. I'm now sold on the soldering iron.  :D I just need to work out the particulars. It does take longer to apply wax this way, but then I'd probably spend that amount of time cleaning up after using the spoon so the time spent waxing with the soldering iron is probably a wash.
Title: Re: Irons - my latest acquisition
Post by: Lester on March 05, 2012, 05:52:49 PM
Sounds like Steve has found a good type of iron for precise control.
This is what I use. It's a Precision Gold soldering iron and station, from Maplin.
There is a photo of it on Amazon here (http://www.amazon.co.uk/PROFESSIONAL-STATION-ADJUSTABLE-SOLDERING-TEMPERATURE/dp/B0025UOAP4), although I note that Amazon have marked it as currently out of stock. Should be available from Maplin direct though.

http://www.maplin.co.uk/48w-lcd-display-solder-station-219133 (http://www.maplin.co.uk/48w-lcd-display-solder-station-219133)
Title: Re: Irons - my latest acquisition
Post by: Lester on March 05, 2012, 05:55:56 PM
I use on of these. http://www.maplin.co.uk/25w-soldering-iron-type-xs-4063 (http://www.maplin.co.uk/25w-soldering-iron-type-xs-4063) powered via a dimmer switch. I have filed the tip to enable it to fit between reeds.
Title: Re: Irons - my latest acquisition
Post by: Theo on March 05, 2012, 06:15:08 PM
Never heat wax over a flame please. Melted wax is inflammable.  The safest way to do this is in an electric wax bath with thermostat, the type used for batik should be suitable.  Second best if you must use a flame please please use a water bath, at least that way there is a limit to how hot the wax can get.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 05, 2012, 06:19:51 PM
I noticed as I was using my new waxing system (flattened piece of 12 guage copper wire) that there's a great deal of heat loss at the tip of the blade. I adjusted the distance of the end of the "spatula" from the tip of the soldering iron such that I could get a good flow down the blade while the blade was in contact with the wax or the reed plate. The level of heat that allowed the blade to keep the wax hot at the application site cause the wax left on the blade to smoke when not in contact with the work. I simply wiped the blade off with a paper towel before putting the tool down to place the next reed.
Title: Re: Irons - my latest acquisition
Post by: Theo on March 05, 2012, 06:31:10 PM
Here are three photos of my waxing/soldering iron.   It is a Weller 20W thermostatic soldering iron.
The pictures are all posed so I have a free hand for the camera.   In the third photo I've placed the wax stick where it would be in use next to the heating element, but the iron would not be lying flat in use, it would be in the sort of position shown in the second photo.
Title: Re: Irons - my latest acquisition
Post by: forrest on March 05, 2012, 06:56:51 PM
Never heat wax over a flame please. Melted wax is inflammable.  The safest way to do this is in an electric wax bath with thermostat, the type used for batik should be suitable.  Second best if you must use a flame please please use a water bath, at least that way there is a limit to how hot the wax can get.

Yes indeed. The vapors of the hot wax can cause a flash fire very easily if exposed to spark or flame. I mentioned 'flame' in my post, because I was instructed by an old school repairman to use an alcohol flame to heat the wax tub, and the waxing spoon. He also advised disposing of the residual wax, as it had lost it's 'fresh' qualities.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 05, 2012, 07:07:21 PM
Here are three photos of my waxing/soldering iron.

Thank you Theo! Almost as good as a video.

I'll get another soldering iron to use as a dedicated waxing tool and add a dimmer switch to allow fine adjustment of the heat.
Title: Re: Irons - my latest acquisition
Post by: Theo on March 05, 2012, 07:19:46 PM
A dimmer switch is not as good as a thermostatic control.  It still gives a constant heat input which means the temp will rise when not in use and will drop once you start melting cold wax.   Thermostatic controlled irons are not desperately expensive and take one more but of guesswork out of the process.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 05, 2012, 07:55:49 PM
A dimmer switch is not as good as a thermostatic control.  It still gives a constant heat input which means the temp will rise when not in use and will drop once you start melting cold wax.   Thermostatic controlled irons are not desperately expensive and take one more but of guesswork out of the process.

I hadn't realized that. Thanks again. I'll get a thermostatic controlled iron then.
Title: Re: Irons - my latest acquisition
Post by: Quebecois on March 05, 2012, 08:12:37 PM
Using the right tool for the right job!

Seems to me that irons allow precision work, using only the wax you need, whether it's for a single reed plate or an entire reedblock.
Title: Re: Irons - my latest acquisition
Post by: Theo on March 05, 2012, 08:16:19 PM
I think if I was waxing many reed blocks a day I would learn the Italian method with spatula and wax bath.  It is probably easier to be quick and neat with this method. I rarely wax more than one set of blocks in a day and the soldering iron is ready to use within 30 seconds of switching on,  I'm sure a wax bath would take longer to heat up.
Title: Re: Irons - my latest acquisition
Post by: diatonix on March 05, 2012, 10:34:54 PM
My wax heater, actually a product designed for cosmeticians and equipped with thermostatic control, also allows me to melt very small quantities of wax at a time. I prefer this method even for "small" jobs such as waxing accidentals etc. It doesn't take many minutes to reach the desired temperature.
I find the Italian spatula rather treacherous and prefer the German type spoon. One "load" contains enough wax for maybe 4 to 5 reeds or a complete outer edge along all the (usually 10 or 11) reeds. Waxing 1 block becomes a matter of a few minutes.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 05, 2012, 10:53:38 PM
I find the Italian spatula rather treacherous and prefer the German type spoon. One "load" contains enough wax for maybe 4 to 5 reeds or a complete outer edge along all the (usually 10 or 11) reeds. Waxing 1 block becomes a matter of a few minutes.

I've been looking for a "spoon" and have found this (http://www.stringsandboxes.de/epages/es117831.sf/en_GB/?ObjectPath=/Shops/es117831_stringsandboxes/Categories/%22Akkordeon%20Werkzeuge%22/Wachswerkzeuge). Is this the tool you're talking about? Interesting idea.
Title: Re: Irons - my latest acquisition
Post by: blafleur on March 05, 2012, 10:57:12 PM
I've never tried the spoon, but a curved eyedropper like the one in the link below and a water bath is what I use. Gives good control and keeps drips in control.
http://www.amazon.com/Fisherbrand-Medicine-Droppers-Curved-Length/dp/B001BU1ZLQ
Title: Re: Irons - my latest acquisition
Post by: forrest on March 06, 2012, 02:03:51 AM
I've never tried the spoon, but a curved eyedropper like the one in the link below and a water bath is what I use. Gives good control and keeps drips in control.
http://www.amazon.com/Fisherbrand-Medicine-Droppers-Curved-Length/dp/B001BU1ZLQ

Have not seen this before.....what a great forum! ;D
Title: Re: Irons - my latest acquisition
Post by: Steve_freereeder on March 06, 2012, 09:15:44 AM
Thanks Steve. Do you use the standard soldering tip or something different - a blade tip of some kind?
The soldering iron came equipped with interchangeable tips of various diameters. I use the smallest one, filed down initially to about 1 mm dia. at the tip, then gently hammered flat so it resembles a small screwdriver blade.

My soldering iron seems to work very well for me and (thanks to advice from Theo and Rees  :|glug ) I have managed to get the job done pretty neatly. But I don't as yet do a lot of waxing. Up to present, I have just been removing a few reed plates to replace the valves on the underside, then rewaxing the plates back into place. However, I have a restoration project in mind, which will involve complete revalving and rewaxing of all the reed plates.
Title: Re: Irons - my latest acquisition
Post by: Owen Woods on March 07, 2012, 02:22:24 AM
An encaustic stylus is really easy. You just plug it in, stick the point into a block of wax and then draw round the plate slowly. The stylus head acts as a nib and wax flows down it onto the block. Dead easy to use, consistent results and it uses a small quantity of wax, which I suspect makes a slight difference to the sound(?).

The other advantage is that it doesn't melt the wax too much, which reduces fumes (but you should still get a solder fume extractor just in case, or work in a very well ventilated space). However, the downside to this is that the wax doesn't flow as well as it does when hotter. Also the tool only works if in direct contact with the thing that you want to wax. These two things mean that you can't use it to let the wax seep into cracks. I have filed a spare tip away such that it can fit into tiny cracks, but it doesn't work terribly well.

So if the reedplates are very close together, as in a Preccy, you have only one option. You need to wax the inside edge of a plate and then press the next one down onto it before it dries. You can do this be modifying another head on an encaustic stylus so that it flows quickly, or you could use a manual batik pen or waxing spoon.
Title: Re: Irons - my latest acquisition
Post by: Quebecois on March 07, 2012, 02:56:03 AM
An encaustic stylus is really easy. (...)
The other advantage is that it doesn't melt the wax too much, which reduces fumes (etc)
Mine does get the wax fluid enough to fill small cracks, etc. It's true though that when the space in tight between reedplates it could be a challenge.
Title: Re: Irons - my latest acquisition
Post by: Lester on March 07, 2012, 01:01:28 PM
A short silent video of me waxing the bass reeds on a Hohner bass block using a soldering iron.

http://youtu.be/dUaHU1vY8f0 (http://youtu.be/dUaHU1vY8f0)

Doesn't show the tidying up phase of which more than usual was needed due to trying to keep out of the way of the camera (well that's my excuse and I'm sticking too it  ;) )
Title: Re: Irons - my latest acquisition
Post by: Prestidigitator on March 07, 2012, 01:19:56 PM
Lester.

That's very instructive. I can see several ways in which to improve my technique i.e. make it less b****y awful.
Title: Re: Irons - my latest acquisition
Post by: Steve_freereeder on March 07, 2012, 01:47:21 PM
A short silent video of me waxing the bass reeds on a Hohner bass block using a soldering iron.
http://youtu.be/dUaHU1vY8f0 (http://youtu.be/dUaHU1vY8f0)
Excellent! Thanks, Lester.   :|glug
Title: Re: Irons - my latest acquisition
Post by: waltzman on March 07, 2012, 02:24:40 PM
This is another temperature controlled soldering iron that works very well.  I use the vertical blade that is visible in the picture on the box.  You can add precisely the amount of heat needed with the trigger. 
http://www.amazon.com/Weller-WEL8200PK-120-Volt-Universal-Soldering/dp/B00002N7S0
Title: Re: Irons - my latest acquisition
Post by: Quebecois on March 07, 2012, 03:36:07 PM
This is another temperature controlled soldering iron that works very well.  I use the vertical blade that is visible in the picture on the box.  You can add precisely the amount of heat needed with the trigger. 
http://www.amazon.com/Weller-WEL8200PK-120-Volt-Universal-Soldering/dp/B00002N7S0
This is a "OFF-LOW-HIGH" kind of manual temperature control. I don't know about the "precise amount of heat" since it's more like a hit and miss trigger operation! I presume that even in the low (100W) position it's more than enough to melt the wax, since it's designed to melt tin solder...
Title: Re: Irons - my latest acquisition
Post by: waltzman on March 07, 2012, 03:47:47 PM
This is another temperature controlled soldering iron that works very well.  I use the vertical blade that is visible in the picture on the box.  You can add precisely the amount of heat needed with the trigger. 
http://www.amazon.com/Weller-WEL8200PK-120-Volt-Universal-Soldering/dp/B00002N7S0
This is a "OFF-LOW-HIGH" kind of manual temperature control. I don't know about the "precise amount of heat" since it's more like a hit and miss trigger operation! I presume that even in the low (100W) position it's more than enough to melt the wax, since it's designed to melt tin solder...


I speak from experience not conjecture.  It works very well and makes a very neat job.  The tip heats quickly and cools quickly so even though the trigger is 'on-off' it is very easy to precisely control the temp of the tip.  All soldering irons are designed to melt solder.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 07, 2012, 04:52:24 PM
Thank you Lester. A very helpful demonstration.

This thread is proving very instructive and helpful.  ;D ;D
Title: Re: Irons - my latest acquisition
Post by: diatonix on March 07, 2012, 07:47:00 PM
Not exactly the kind of work I like to do while being videotaped: http://www.youtube.com/watch?v=yjGaLwqrtOs&feature=youtu.be
Title: Re: Irons - my latest acquisition
Post by: rees on March 07, 2012, 08:02:43 PM
Not exactly the kind of work I like to do while being videotaped: http://www.youtube.com/watch?v=yjGaLwqrtOs&feature=youtu.be

That's a very neat job. Where did you get the spoon?
Title: Re: Irons - my latest acquisition
Post by: Lester on March 07, 2012, 08:07:31 PM
Not exactly the kind of work I like to do while being videotaped: http://www.youtube.com/watch?v=yjGaLwqrtOs&feature=youtu.be

I bow to a master  ;D
Title: Re: Irons - my latest acquisition
Post by: diatonix on March 07, 2012, 08:14:52 PM
@Rees: I make these "spoons" myself, using thin metal sheet.
Title: Re: Irons - my latest acquisition
Post by: Telemorris on March 07, 2012, 09:00:56 PM
@Rees: I make these "spoons" myself, using thin metal sheet.

Thank you Diatonix! I really enjoy seeing tools created by craftmen for their own use. It's wonderfully logical and simple. I'll be making one of these in the coming month.

Can we assume you solder the joints near the handle to keep the wax from leaking out?

Thank you very much for the video.

And a big heartfelt thank you to all the professionals and amateurs who share their work and techniques on this Forum. There is a great deal to learn about working on these instruments. The wealth of knowledge and willingness to share that knowledge is astounding. What an incredible group! I can't thank all of you enough.
Title: Re: Irons - my latest acquisition
Post by: diatonix on March 07, 2012, 09:35:55 PM
You are welcome, Ed and yes, the joints are soldered. Actually the tool used in my video works better with the slightly thicker Italian reeds, that's why I'd suggest a spoon which is a bit more pointed when dealing with Hohner reeds. The spoon is even faster when gaps are small, such as in chromatic accordions, although then my technique is slightly different.
Title: Re: Irons - my latest acquisition
Post by: tirpous on March 07, 2012, 11:03:17 PM
Thanks for the video.  I notice you seem to be pushing the plates firmly in place.  Is there already wax on the end to keep them from moving while you do the spoon thing ?
Title: Re: Irons - my latest acquisition
Post by: Prestidigitator on March 08, 2012, 08:06:02 AM
Diatonix,

That's a fascinating demo and I like the look of the spoon and its product - in your hands, at any rate.

It's out with the brass sheet for me, and a soldering iron with solder this time.

Title: Re: Irons - my latest acquisition
Post by: rees on March 10, 2012, 11:52:33 PM
@Rees: I make these "spoons" myself, using thin metal sheet.

So is it just folded over at the bottom to form a reservoir and the wax flows out of the pointy end?
Title: Re: Irons - my latest acquisition
Post by: diatonix on March 11, 2012, 06:39:23 AM
I prefer a flat v-shaped (triangular) bottom which makes it easier to wipe off wax that is not inside the reservoir, either on the rim of the wax heater or/and a newspaper. The u-shaped opening can easily be made narrower or wider, according to the nature of the work it is supposed to do. Since it is relatively easy to make such a "spoon" you may end up with a  collection of 3 or 4 of them, all slightly differently shaped.  
Impurities that are often present in the wax do sometimes clog the opening. Such a problem is rapidly solved with a thin steel strip.
Title: Re: Irons - my latest acquisition
Post by: forrest on March 11, 2012, 05:21:07 PM
Thanks again for posting the video, Olav.  I have not seen anyone else using this method, in my limited view. The tool you are using seems to open up great possibilities compared to using the 'spatula' or even a fancy electric iron, especially for production work. It seems to make perfect sense in this regard, but looks like it would require a good bit of practice to achieve the fine results that you are getting!
Title: Re: Irons - my latest acquisition
Post by: diatonix on March 11, 2012, 05:42:02 PM
Maybe it's too easy for me saying this, but I don't think it requires much more than two steady hands - and those are also needed when using a soldering iron & wax-stick.  Try it out with a couple of extra reeds on a spare block you may have lying around!
Title: Re: Irons - my latest acquisition
Post by: Owen Woods on March 11, 2012, 05:53:03 PM
The advantage of this method is that the holding and dispensing actions are combined into one unit, albeit with the heating element separate. This means that you only need one hand to apply. The soldering iron method combines the dispensing and heating element, but the holding element is separate, meaning that you need two hands. The encaustic stylus combines all three elements, which is convenient, but the method does have disadvantages as I detailed above. I still think that an encaustic stylus is a good addition to anybody's armoury, it is great for quick and easy repairs, say waxing in a single reedplate.
Title: Re: Irons - my latest acquisition
Post by: waltzman on March 11, 2012, 06:19:52 PM
With my solder gun technique I dip the blade tip into unmelted wax and apply just enough power to melt the wax.  The blade will hold enough wax to do at least one edge of a reed.  It is slower than the spoon but very neat and clean and it only takes one hand holding the solder gun and one holding the reed block just like the spoon.  It also avoids the stinking pot of wax. 
Title: Re: Irons - my latest acquisition
Post by: KLR on August 08, 2013, 07:48:54 PM
BUMP

Not exactly the kind of work I like to do while being videotaped: http://www.youtube.com/watch?v=yjGaLwqrtOs&feature=youtu.be

Thanks as well for that video, invaluable to see these things done.  I took a screen cap of that to show what your spoon looks like. 

(http://farm8.staticflickr.com/7299/9465144157_885fce36d1.jpg)
This business had me confused for a while, as it's difficult to find pictures of what these things actually look like.  The House of Musical Traditions for instance in their Reed & Wax Supplies (http://www.hmtrad.com/catalog/winds/sbx/sbx-part.html#reed) section sells a waxing spoon, but I couldn't figure out how you'd use such an implement:

(http://farm4.staticflickr.com/3718/9467893950_b8f05e32a2_o.gif)

Does this have a trough like yours?  If it's just flat sheet I don't see how the wax could stay liquid long enough to work at all.  Someone mentioned the Italian model of spoon, too - how does that differ from the German?

I found a photoset documenting a journey to the Hohner factory, there are some pics of reeds being waxed:

(http://www.peterunbehauen.de/BilderFolk/06-trossingen/06peterunbehauen643.jpg)
The caption for this pic reads:  "17. Renate Meyhof does the waxing of the reed blocks, the wax is heated in the container under the red exhausting system."

(http://www.peterunbehauen.de/BilderFolk/06-trossingen/06peterunbehauen645.jpg)
The caption for this pic reads:  "18. Filling in the wax to keep the reedblocks air tight."

Note how their tool has a straight handle, unlike diatonic's with its sharply angled trough.  Factory Tour Hohner Trossingen (http://www.peterunbehauen.de/p/06-hohner.html).  Hohner sells a fancy model with an internal tank for wax, rather like the batik tools.  Interesting that their own people persist with using spoons. 
Title: Re: Irons - my latest acquisition
Post by: an bosca ceoil on August 08, 2013, 10:18:32 PM
Those "italian" spoons have no trough, they are just a spatula.
They are used the opposite way up to how shown.
Dipped into the wax which runs down to the point when you upend it onto the block.
Difficult!
SimplePortal 2.3.5 © 2008-2012, SimplePortal