Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: petefoth on September 22, 2008, 05:44:17 PM

Title: First steps in repair
Post by: petefoth on September 22, 2008, 05:44:17 PM
I have a cheap and cheerful Galotta C/F box in a tasteful shade of red with a closed keyboard. One of the buttons got stuck and, in efforts to free it I managed to separate the button from the bit of wood it was stuck to - see picture for gory details.

I assume that to repair it properly I need to get at the internals of the keyboard and I've go no idea where to start. There are no obvious screws to undo. There is only a small wire loop, which looks like the top end of a split pin, sticking out of the black bit of the keyboard, just above where it meets the red bit (I'm really getting on top iof these technical terms {:-) above where the strap bracket is attached. I've tried pulling this with a reasonable force, but it didn't want to move.

I've no idea what to try next, so any ideas will be very gratefully received. Do I need to be more brutal with the wire loop? Can I try stickng the button back without getting at the internals?

Thanks in advance

Pete
Title: Re: First steps in repair
Post by: an bosca ceoil on September 22, 2008, 07:11:29 PM
DON`T PULL YOUR WIRE!!  ;D
If you do succeed in removing it you will wind up with far more problems than you already have i.e. all the levers floating loose inside the keyboard.
Best bet might be epoxy glue applied carefully without dismantling anything.
Title: Re: First steps in repair
Post by: triskel on September 22, 2008, 11:02:46 PM
DON`T PULL YOUR WIRE!!  ;D

Though unfortunately, that's sometimes the "best fix" for such problems!!!  :o (Though I'd push it out, rather than pull it... )

Sticking keys are unfortunately very common with instruments made in Klingenthal (like this one), but it wasn't until I started going there, and dealing with some of the makers, that I came to understand why. The trouble is that the town is up in the mountains, right on the Czech border (the border post is down a side street!), and the air is extremely dry there, so if you then take an instrument made under such conditions to a damper climate (especially a much damper climate, like we have in Ireland  ::)) then actions are inclined to seize-up due to wood swelling.

Sometimes it's simply that the button has started to catch on the edge of its keyboard hole, in which case regluing it in such a way that it no longer does so will suffice, but often the wooden lever under the button has expanded, or twisted, or the slot has shrunk, so that it's sticking, and removal of the pin can become the best option to be able to smooth the offending woodwork. But it's not something that I'd undertake lightly...  :(
Title: Re: First steps in repair
Post by: petefoth on September 23, 2008, 07:08:45 AM
DON`T PULL YOUR WIRE!!  ;D

OK I won't pull the wire!

The problem is indeed that the button has started to catch on the edge of its keyboard hole. I will try just gluing it back. I may try sanding down the button  a little or carefully enlarging the keyboard hole.

Thanks for your help

Pete
Title: Re: First steps in repair
Post by: petefoth on September 24, 2008, 08:04:04 AM
Done it! After some delicate work with a file, a matchstick and some woodworking glue the offending button is now back in place and functioning. As a diversion I even discovered how to take the grille off. Clearly it's time for me to set up as a box repairer in competition with others on this site. How hard can it be {;-)

Thanks for your help - it wouldn't have been the same if I had pulled the wire.

Cheers

Pete
SimplePortal 2.3.5 © 2008-2012, SimplePortal