Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: syale on June 25, 2012, 02:04:00 AM

Title: HA-114 screws
Post by: syale on June 25, 2012, 02:04:00 AM
I have 2 hohners (both HA-114), an older made in Germany 'G' and a newer one 'C' that the box says made in Germany but it doesn't say it on the underside of the button box.

On the grills for them the older one has the grill secured with tiny screws and on the newer one the look like nails. On the newer one some of the nails are lifting slightly so I would like to replace with screws. The question is what size are they?

Stephen

Just bought a 2915 today on eBay (http://tinyurl.com/6qggzvd) for US$290 so that makes 3 in a matter of 3 months. I need to slow down my buying and speed up my playing... The good thing is that my wife picked it up today and after looking at my button number notes was able to rattle of 'You are my sunshine'. I was very proud of her.

Title: Re: HA-114 screws
Post by: old geezer on June 25, 2012, 03:31:57 AM
On the grills for them the older one has the grill secured with tiny screws and on the newer one the look like nails. On the newer one some of the nails are lifting slightly so I would like to replace with screws. The question is what size are they?

the original were nails with a slot cut into the head to imitate a screw to hold the grill to the 2 wooden edges,
 before being screwed to the pallet fondo

when any require replacement, I cut a gold dressmakers pin (on an angle) to length and hammer home  (:)
Title: Re: HA-114 screws
Post by: syale on June 25, 2012, 04:44:06 AM
Definitely screws!
Title: Re: HA-114 screws
Post by: Prestidigitator on June 25, 2012, 07:01:51 AM
I have 2 hohners (both HA-114), an older made in Germany 'G' and a newer one 'C' that the box says made in Germany but it doesn't say it on the underside of the button box.

On the grills for them the older one has the grill secured with tiny screws and on the newer one the look like nails. On the newer one some of the nails are lifting slightly so I would like to replace with screws. The question is what size are they?

Stephen


Mine is a 16-fold 114C Made in Germany but with a plastic fingerboard. The metal grille is held on to the wooden sides by small flathead nails, which, as they cannot be countersunk, stand proud of the metal. That makes them look as if they're coming out, but in my case, that's not so. Personally I don't think you've got anything to worry about.
Title: Re: HA-114 screws
Post by: Theo on June 25, 2012, 07:43:32 AM
A photo would clarify the problem.
Title: Re: HA-114 screws
Post by: old geezer on June 25, 2012, 08:36:44 AM
Definitely screws!

I stand corrected

I have several HA114's with the silver ends and one with black ends and it appears that these all have nails securing the grill to the wood ends.

Is the screw version unique to the gold end version, or has screws been retro fitted by a previous owner?
Title: Re: HA-114 screws
Post by: Theo on June 25, 2012, 08:45:48 AM
The normal setup is the metal grill is secured to the small upright wooden end pieces by nails, and each end there is a bracket the holds the whole grill in place.  Each of those brackets is secured by a small round head screw.  These are often replaced by nails because the correct screws are almost impossible to obtain.
Title: Re: HA-114 screws
Post by: syale on June 26, 2012, 03:53:16 AM
I have ordered a packet of #0 x 3/8" and a packet of #1 x 3/8" from a store here in the USA. I will let you know if they are the right type.
Title: Re: HA-114 screws
Post by: Theo on June 26, 2012, 08:02:28 AM
I have ordered a packet of #0 x 3/8" and a packet of #1 x 3/8" from a store here in the USA. I will let you know if they are the right type.

You are fortunate to find those,  in the UK it's almost impossible to find such small screws.
Title: Re: HA-114 screws
Post by: Prestidigitator on June 26, 2012, 08:58:55 AM
I have ordered a packet of #0 x 3/8" and a packet of #1 x 3/8" from a store here in the USA. I will let you know if they are the right type.

You are fortunate to find those,  in the UK it's almost impossible to find such small screws.

The only places I've had any luck in finding new miniature screws of that size in the UK, in sensible small-ish quantities, are a few specialist model shops (both aircraft and marine) and online suppliers (e.g. modelfixings.co.uk). The downside is that the type and material range is very limited, as most are steel self-tappers with Phillips heads. Slotted heads are as scarce as hens' teeth. Small brass screws,  when found, are best for "fitting and forgetting", as they are so soft that they will readily shear off on dismantling or reassembly.

Such outlets are also a source for Hohner-style miniature bellows pin washers.
Title: Re: HA-114 screws
Post by: Mike Hirst on June 26, 2012, 09:56:16 AM
I can recommend A.G.Thomas (Horology and Jewellery Suppliers) as source for small screws and other fittings.

http://www.agthomas.co.uk/

Title: Re: HA-114 screws
Post by: syale on June 26, 2012, 05:58:03 PM
I ordered RWB0006 and RWB0106 from Micro Fasteners (http://www.microfasteners.com/catalog/standard.cfm?Category=TWS&SubCategory=RWB) (Packet of 100) for $4.50 a packet. shipping was an extra $4
Title: Re: HA-114 screws
Post by: syale on July 01, 2012, 05:38:59 AM
Screws came today and the size #0 are perfect for the grill. I have lots left (:)
SimplePortal 2.3.5 © 2008-2012, SimplePortal