Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: waltzman on July 08, 2012, 07:28:05 PM

Title: spring tension
Post by: waltzman on July 08, 2012, 07:28:05 PM
I have just gotten a Hohner HA114 four stopper off of Ebay and tuned it for cajun music.  I suspect the spring tension needs to be a bit heavier to keep the large pallets air tight but it feels like the tension is more than it needs to be.   Does anyone have a good technique to recommend for adjusting the spring tension?

Michael
Title: Re: spring tension
Post by: Martyn on July 08, 2012, 11:05:05 PM
If you are experiencing leaks around the pallets it is far more likely they are not seating properly and need a little adjustment, rather than the spring tension being incorrect.

Martyn
Title: Re: spring tension
Post by: waltzman on July 08, 2012, 11:28:32 PM
No.  No leaks.  Just heavy buttons.  Much heavier than my other two and three row Hohners.
Title: Re: spring tension
Post by: syale on July 08, 2012, 11:54:05 PM
I disassembled the treble linkages, took out the springs and put a small kink in the spring, only 1/8” off and that softened the buttons tremendously. I can take some pictures if it makes it any clearer. I have shown a representation of what I did.

1. Take the treble end off.
2. Unhook all the springs from the linkages to take the tension away.
3. Remove the screws holding the linkage system to the box and remove the linkage assembly.
4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the indvidual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.
6. Put a small kink in the spring. I made a 1/8" adjustment with snipe nose pliers to bend the spring.
7. Put everything back in reverse order.

I should really video stuff like this...
Title: Re: spring tension
Post by: blafleur on July 09, 2012, 02:09:44 AM
Syale, you got that from Cory, he musta got that from Marc Savoy?  That boy can sure play but he better quit taking accordions apart, his fingers are too delicate for tools.  You can tell him I said that.  ;)

Bryan Lafleur
Title: Re: spring tension
Post by: waltzman on July 09, 2012, 02:24:08 AM
Thanks Syale.  I assume you put the kink in the arm of the spring that goes toward the button?
Title: Re: spring tension
Post by: syale on July 09, 2012, 03:43:32 AM
Cory told me to put a screwdriver down through the keyboard and bend the spring! My background is instrumentation so I was a little more methodical in my approach. He is a great player. He played in my kitchen when I first bought the accordion and he, very graciously, came to my house to see if it was OK. Really nice guy.

You are correct the kink goes in arm to the button. Hopefully you can see it in the pictures. I forgot to add that you need to remove the grill and the keyboard.
Title: Re: spring tension
Post by: waltzman on July 09, 2012, 02:11:39 PM
Perfect.  Thanks.
Title: Re: spring tension
Post by: Larus on July 10, 2012, 08:47:13 AM

I should really video stuff like this...
If you could find the time, a video would be much better for us "biffs" to follow :o
Title: Re: spring tension
Post by: Larus on July 10, 2012, 09:39:35 PM
I decided to have a go at this and to my amazement I managed it and it really works.
The old Hohner 1 row, 4 stop, is now much more responsive and easier to play. No loss of air through the pallets either.
Great tip.
Many thanks ;D
Title: Re: spring tension
Post by: Theo on July 11, 2012, 08:50:27 AM

4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the indvidual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.


A small refinement is to thread a suitable thin rod in from the opposite end as you withdraw the axle rod, this will allow you to keep all the lever arms in place, and will make re-assembly a little quicker.
Title: Re: spring tension
Post by: Larus on July 13, 2012, 11:21:08 AM

4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the individual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.


A small refinement is to thread a suitable thin rod in from the opposite end as you withdraw the axle rod, this will allow you to keep all the lever arms in place, and will make re-assembly a little quicker.
Like all good ideas, it's obvious when somebody suggests it.
I'd never even thought of doing this.
Another great tip.
Title: Re: spring tension
Post by: Sandy Flett on August 07, 2012, 01:36:19 PM
I have just carried out syale's procedure on the 8 bass springs and air button spring on my Erica, also using Theo's tip of feeding a wire in as withdraw the rod to keep everything in place. It was a bit fiddly as the whole mechanism would not come out in one piece, so I did it in situ; this also meant I had to do two springs at a time as the rod ends came up against the side of the instrument when only about 60% withdrawn.

However, after a quick tune I am pleased with the result. The buttons are noticeably lighter to play, with no loss of air at the reeds and just a little bit at the air button if I press the bellows hard enough with no buttons pressed.

Thanks for the technical tips and inspiration to try such a thing oneself.
Title: Re: spring tension
Post by: Adam-T on August 07, 2012, 01:41:37 PM
maybe a bit of better pallet leather may sort the air button leak (or put a stronger spring on it) ..

I`d like to lighten the action on a '90s Delicia Hlavacek Heligonka but don`t know if that would cause leaks or the best way to do it. the action is similar to Italian boutique boxes
Title: Re: spring tension
Post by: Martyn on October 19, 2012, 10:00:45 AM

4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the indvidual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.


A small refinement is to thread a suitable thin rod in from the opposite end as you withdraw the axle rod, this will allow you to keep all the lever arms in place, and will make re-assembly a little quicker.

It's a good idea to screw the action to a board before you do this. That will make the whole operation a lot easier.

Martyn
Title: Re: spring tension
Post by: Lester on December 31, 2012, 08:12:55 PM
Spent a useful half hour in the workshop this afternoon putting a kink in the end of the springs of the treble end of my Hohner 1 row. By trial and error I have no got an air tight but appreciably lighter action box  (:) (:)
Title: Re: spring tension
Post by: Etienne on July 11, 2013, 12:20:37 PM
I tried this yesterday evening on my 1040 and now feel to have a new box ! THANKS  :||: :||: :||:
Title: Re: spring tension
Post by: Johnniez on June 19, 2016, 09:36:59 AM
I did all 3 ha-114 using this method and the difference in feel and action is enormous.. Thanks ever so much for posting this.

I did screw it down to a board and it went pretty smooth.. Bit of a time with the first box  , bent the rod a couple of times. Other 2 boxes went great.. All 3 now have the same feel.

Johnnie
Title: Re: spring tension
Post by: playandteach on June 19, 2016, 11:01:14 AM
Can I do this to the bass end of a Hohner Erika? I've tried replacing the springs, but still too stiff. It's the only reason I'm not picking it up to play more often.
Title: Re: spring tension
Post by: Harmonicatunes on June 20, 2016, 11:15:14 AM
All very interesting. I love the sound of the HA114s, and have a few of them. However the keys do take some effort, which becomes noticeable at higher speeds.

The spring mod described here sounds good, but, as with most things, it is perhaps best left to the experts. Would any of the local fettlers offer such a service? It could perhaps be done by sending the key/pallet assemble only, rather than the entire box.
Title: Re: spring tension
Post by: gettabettabox on June 20, 2016, 07:23:27 PM
i've done this on all my ha one-rows, never had to remove or dissemble the action, just release the spring tension before gently persuading the ''kinks.''
Title: Re: spring tension
Post by: Robyn Foley on March 07, 2020, 06:54:51 AM
Theo and others, I was looking for some instructions on button tension softening, and found this comment on a Cajun site:

".............To loosen springs is easy. I once watched an old Cajun accordion builder take a 12 inch stainless steel ruler, place it's edge into all of the button springs at once, and bend downward in one quick and sure motion which stretched every spring to the exact same tension in about 3 seconds. Smart ole feller. "

Could I please have some comments on whether that would be something to try on my Sander? Any thoughts about it at all.
I spoke to an accordion repairer a couple of states away from me, and he said he would have a go at the springs/button softening, but that he had not done it before.
If I am going to get someone to do it for me, I was hoping they would have done it before, but in case that cannot be, then some clear easy instructions for me to give to someone would be appreciated.

I did see the instructions earlier posted by Syale, however if the 'ruler' method is feasible, that might be something I could present to a first time repairer, or even attempt myself.

Thank you
Title: Re: spring tension
Post by: Theo on March 07, 2020, 08:19:40 AM
Most Cajun accordions use coil springs. Italian boxes use hairpin springs so the bending process has to be different.
Title: Re: spring tension
Post by: komat on January 29, 2026, 04:34:36 PM
Is here a similar method to add tension to a spring?
Title: Re: spring tension
Post by: mselic on January 29, 2026, 06:54:42 PM
Is here a similar method to add tension to a spring?

The only method I know of is to grab both ends of a single coil spring with pliers and twist the coil in on itself. This will tighten the spring back up again to some degree.
Title: Re: spring tension
Post by: rees on January 29, 2026, 07:21:39 PM
Is here a similar method to add tension to a spring?

The only method I know of is to grab both ends of a single coil spring with pliers and twist the coil in on itself. This will tighten the spring back up again to some degree.

Coil springs can be shortened to increase tension.
Cut off the loop at one end of the coil with a side-cutters. Place the spring on a flat surface and insert two thin knives between the first and second coil.
Hold one knife upright and push the other knife against the first loop until it is at 90 degrees to the coil.
If it's still not strong enough repeat the process.
Title: Re: spring tension
Post by: tirpous on January 29, 2026, 07:28:38 PM
Quote
Place the spring on a flat surface and insert two thin knives between the first and second coil.
Hold one knife upright and push the other knife against the first loop until it is at 90 degrees to the coil.

True cutting-edge technology !  ;D
Title: Re: spring tension
Post by: mselic on January 29, 2026, 08:14:30 PM
Sorry, yes, I should have said that cutting off a coil would create a stiffer spring. I kind of assumed that was obvious. When I’ve lightened coil springs on cajun boxes in the past, and maybe gone just a touch too far, I just coil the spring back in on itself as described for a quick re-stiffening adjustment. Often I just make new springs from a long coil using the same method Rees described.
SimplePortal 2.3.5 © 2008-2012, SimplePortal