Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Interesting Bass Valve Supports  (Read 1541 times)

0 Members and 1 Guest are viewing this topic.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Interesting Bass Valve Supports
« on: July 31, 2012, 06:29:31 PM »

I have discovered this in a recently acquired Hohner  pre-Corona. This was done as a restoration by  (I am guessing) a shop, or an experienced repair person. In my narrow little world, I have not run across this technique or style of bolstering bass valves, but maybe it's commonplace in the great beyond?
  Comments welcome!
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Interesting Bass Valve Supports
« Reply #1 on: July 31, 2012, 07:09:50 PM »

Looks like the plastic valve assisters have just gone curly with heat or age or whatever
Logged
Q: How do you cure MAD?
A: Buy more Boxes

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Interesting Bass Valve Supports
« Reply #2 on: July 31, 2012, 07:27:27 PM »

Looks like the plastic valve assisters have just gone curly with heat or age or whatever

Perhaps at first glance. They are deliberately flexed and fastened to the valve via clear tape in a flying buttress effect. The plastic boosters also look like they have a notch whereby the amount of flex can be lessened or increased. This is repeated for the inside reeds as well. And they seem to be performing the intended task without problem........ ::)
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Interesting Bass Valve Supports
« Reply #3 on: July 31, 2012, 08:00:09 PM »

This and similar methods are quite frequently used by some tuners (incl. myself) as a remedy to certain problems (fluttering) caused by German type combi valves (especially larger ones). In my own boxes I prefer Italian style valves (with steel "springs") when dealing with 60mm+ bass reeds.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Interesting Bass Valve Supports
« Reply #4 on: July 31, 2012, 08:01:32 PM »

So are they normal combis which have been modded like this ?
Logged
Q: How do you cure MAD?
A: Buy more Boxes

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Interesting Bass Valve Supports
« Reply #5 on: July 31, 2012, 08:12:42 PM »

I should say so. In order to do so, the top plastic flap should be removed and re-attached with new glue. Otherwise many of them, especially older ones, will just fall off.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Interesting Bass Valve Supports
« Reply #6 on: August 02, 2012, 06:26:41 PM »

I have seen versions of this done on older accordions, a advantage is it may keep valves from getting caught in bellows folds.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal