Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: martini 2 row b/c keyboard springs  (Read 1633 times)

0 Members and 1 Guest are viewing this topic.

blackdot1234

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 152
martini 2 row b/c keyboard springs
« on: November 14, 2012, 05:08:40 PM »

can anyone help in how to take out wire holding levers in keyboard as 2 springs are broken it has wooden levers in keyboard and wire to the rubber mounted pallets
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: martini 2 row b/c keyboard springs
« Reply #1 on: November 14, 2012, 05:40:36 PM »

Usually there is a wire axle rod that the levers pivot on. If the keys must be removed, then the only way is to pullout the axle rod.  It is not easy. The main difficulty is usually getting hold of the end of the rod with sufficient grip to pull it out.  It can be very tight.  Second main difficulty is getting the rod pushed back in without bending it.  If you do manage to shift the rod then lay a strip of gaffs tape over the buttons before pulling it out, this will prevent the levers with intact springs from flying across the room.
Good luck!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blackdot1234

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 152
Re: martini 2 row b/c keyboard springs
« Reply #2 on: November 14, 2012, 05:44:50 PM »

is there any way of replacing lever springs without pulling the rod out are springs fixed to levers
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: martini 2 row b/c keyboard springs
« Reply #3 on: November 14, 2012, 07:41:09 PM »

is there any way of replacing lever springs without pulling the rod out are springs fixed to levers

I'm not familiar with that model so I'm not sure.  If there is a screwed on plate on the back of the keyboard that would give you access to the springs.  Another possibility is to take the whole keyboard assembly off,  this usually involves removing two big screws from inside the instrument, one at each end of the keyboard.  It is possible then that the keys will then lift up far enough to get access to the springs.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blackdot1234

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 152
Re: martini 2 row b/c keyboard springs
« Reply #4 on: November 14, 2012, 08:35:08 PM »

this keyboard is solid thin wire axel in centre of inside edge of keyboard each lever is in a mortice with tiny groove to hold one side of spring the spring i think must be fixed to lever otherwise spring would move in mortice  has anyone fixed springs on this type of accordion  any help would be of great help thanks
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: martini 2 row b/c keyboard springs
« Reply #5 on: November 14, 2012, 09:33:57 PM »

I have fixed similar Chinese ones, (though not Martini branded) as described in my first reply.  If there is an easier way I would love to know! 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blackdot1234

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 152
Re: martini 2 row b/c keyboard springs
« Reply #6 on: November 14, 2012, 11:38:14 PM »

if i damage parts while trying to fix springs is there new or second hand parts available
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: martini 2 row b/c keyboard springs
« Reply #7 on: November 15, 2012, 07:58:59 AM »

Probably not.  If you can find a retailer who sells the instruments from new they might have parts available.

Lack of spares is the biggest disadvantage of the cheaper Chinese instruments.   Conversely availability of spares is one of the big plusses of buying a Hohner where parts are available even for models made half a century ago.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blackdot1234

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 152
Re: martini 2 row b/c keyboard springs
« Reply #8 on: November 15, 2012, 09:20:15 AM »

thanks for all the advice and info on this problem i was trying to fix for a girl to start learning accordion
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal