Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Should I?  (Read 1933 times)

0 Members and 1 Guest are viewing this topic.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Should I?
« on: November 25, 2014, 12:19:10 PM »

This Dedenis I am restoring, has the shrivelled remains of a sheet of chamois leather under the pallets, with holes cut through it,for the reed ports. The pallets are faced with normal, felt backed leather facings. Should I replace the chamois?
The whole keyboard, with pallets attached comes off the body, so could I (should I) reface the pallets without unscrewing them from the levers? The pallets are held on by small screws, which will certainly be a problem to get out, and probably impossible to re-tighten fully. They pallets are also not in alignment with one another, so I'm loth to take them off, and would like to avoid it, if I can.

John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Should I?
« Reply #1 on: November 25, 2014, 12:36:50 PM »

Replacing the pallet facings will mean that the pallets will need to be re-aligned because its unlikely that the new material will be the same thickness.  Also getting the old stuff off, cleaning the surface and attaching and trimming the new material will all be made more difficult with the pallets in place.  And there is always the risk that while doing all this you can bend or even break some of the levers.  There are various tricks to removing old screws, but if there is some rust there is a good chance some will break, so have some spares ready.  When you have the new facings fitted and the pallets back in place you will need to spend a fair bit of time making small adjustments to the levers in order to get the pallets airtight.

The sheet of chamois could be original or might be an attempt to cure leaky pallets.  If original it would have been glued down flat.  I think it more likely that it was an amateur attempt to make the pallets airtight - but it probably failed.   There aren't any shortcuts to getting pallets to seal.  The base board has to be smooth, flat and free of cracks, the pallet facings have to be flat and with some softness to them, the pallets themselves have to be flat, the pallets have to be centralised over the holes and the pallets have to lie completely flat.  Looking at your picture I would remove the pallets, but if the screws are rusted, and the screw holes are enlarged I would be prepared to make a full new set of pallets. 

Good luck!
« Last Edit: November 25, 2014, 12:47:13 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Should I?
« Reply #2 on: November 25, 2014, 01:26:29 PM »

Hmmm, new pallets, now that sounds like a good way to go. Thanks Theo.
I shall look through the archives, for hints on making pallets.


John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Should I?
« Reply #3 on: November 25, 2014, 03:41:45 PM »

I don't think its been discussed/

You need a small accurate circular saw.  Some fine grained timber that is not going to warp.

measure the pallets length, width, thickness.   Cut material into one or two convenient lengths.  Cut to length and thickness, and work any side chamfer or saw cut.  (probably no saw cut on the Dedenis)  then sand smooth, finally cut into pallet lengths.  Any shaping to the cust ends is best done by hand on a sheet of sandpaper glued to a flat piece of wood.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Should I?
« Reply #4 on: November 25, 2014, 04:24:49 PM »

« Last Edit: November 25, 2014, 04:30:46 PM by Cugiok »
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Should I?
« Reply #5 on: November 25, 2014, 05:28:22 PM »

Hardwood is not necessary.  Iroko is rather coarse grained for such small components, and it's not the easiest timber to work. Pear works easily, or walnut, alder, poplar, or the kind of old yellow pine that you can't buy any more but you might find in old furniture or fittings.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Should I?
« Reply #6 on: November 25, 2014, 08:00:56 PM »

I'd go along with alder, pear and poplar (all technically hardwoods, but easy to work and with "mild" grain) but my favourite is lime (aka linden, or basswood in the US), an easily worked "soft hardwood", for centuries the timber of choice for fine carving, with negligible grain, light weight and a lovely close texture that's easy to bring to a smooth flat finish, even with only hand tools.  IMHO walnut can be a bit difficult to work, especially if you're not an experienced woodworker. Other opinions may vary.......

Cheers
Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal