Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed valves - which size to use  (Read 1478 times)

0 Members and 1 Guest are viewing this topic.

tirpous

  • Hero Member
  • *****
  • Online Online
  • Posts: 1403
Reed valves - which size to use
« on: December 03, 2014, 08:33:35 PM »

I'm doing a retune/overhaul on the bass side of an older Double Ray.  On the low bass reeds I could use 'terzetti' leathers which are long enough but just so, or cut down larger and slightly thicker 'bass' leathers.  Both would close the slot, but I suspect response may be different, etc...  Should one always use the smallest valve that will fit, or is there some kind of guideline to follow ?



Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed valves - which size to use
« Reply #1 on: December 03, 2014, 08:40:56 PM »

If you use leather on bass reeds it's essential to also use helper springs.  If you don't have them then user the thicker of the valves you have.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed valves - which size to use
« Reply #2 on: December 04, 2014, 10:20:22 AM »

When replacing either leather or plastic valves you need to make sure you're matching the 'springiness' of the new valve with the one you're replacing.  As Theo says with leather valves on larger reeds - the only real way of getting this springiness is to glue a helper spring to the top so that it gives enough resistance.  You see this on all factory fitted leather valves.  Plastic valves for bass reeds usually have several plastic layers on top which perform the same function.

What you're trying to achieve is the valve opening easily under the lowest pressure you want the reed on the other side to begin sounding.  But that has to be balanced with the fact that you also want it to snap shut as quickly as possible after the reed has finished sounding.  You need the latter both to give a nice clean finish to the notes - as well as allowing the reed in the opposite bellows direction to start cleanly.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

tirpous

  • Hero Member
  • *****
  • Online Online
  • Posts: 1403
Re: Reed valves - which size to use
« Reply #3 on: December 04, 2014, 10:10:05 PM »

Thanks for the replies.  I have boosters so all options remain open. I will experiment on a couple of reeds and see how it works.

On this Hohner box, the bass leathers had a mylar booster about 0.12 mm thick, no booster on octave basses.  But these leathers are noticeably thicker than my replacements.  I guess these thick leather valves are no longer available.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed valves - which size to use
« Reply #4 on: December 04, 2014, 11:07:37 PM »

Best just to try what you have. There don't seem to be any very precise rules about valving.  A bit of trial and error should determine what works.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal