Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Change in Outside Row Sound  (Read 5246 times)

0 Members and 1 Guest are viewing this topic.

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Change in Outside Row Sound
« Reply #20 on: April 09, 2016, 02:20:02 AM »

.... for some reason my low reed played on two of my high notes even though I had it turned off.  I turned the low reed on and then turned it off again and those two notes played normally afterwards... weird.   
It sounds like a misalignment between the block and pallet holes and/or a sticking slider.
You will have to ensure that everything is lined up properly.

..  Is it OK to have straps added to an antique accordion?
It is but don't do anything drastic yet. You may not need to do that at all.
First thing to do is check that the air holes in the blocks are aligned with the holes in the pallet board.

Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Change in Outside Row Sound
« Reply #21 on: April 09, 2016, 02:26:21 AM »

if this is the same box that had the replacement grill,... fairly straightforward to remove it and check if it's anything to do with the coupler mechanism? (selectors that activate low octave set.)
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Change in Outside Row Sound
« Reply #22 on: April 09, 2016, 02:29:21 AM »

...once removed, you can operate the mechanism manually to confirm that the sliders are working freely.
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Change in Outside Row Sound
« Reply #23 on: April 09, 2016, 02:45:31 AM »

...that will confirm coupler/mechanism operation, but the crucial part is inside where this links to the sliders and their pivot.
Logged

John Cohen

  • Member
  • *
  • Offline Offline
  • Posts: 33
Re: Change in Outside Row Sound
« Reply #24 on: April 09, 2016, 02:50:17 AM »

...that will confirm coupler/mechanism operation, but the crucial part is inside where this links to the sliders and their pivot.

I think the mechanism is working fine.  Everything plays great and the couplers are working perfectly once again.  It's just the tone of the outside row (and the lack of tremolo) that is off. 
Logged

John Cohen

  • Member
  • *
  • Offline Offline
  • Posts: 33
Re: Change in Outside Row Sound
« Reply #25 on: April 09, 2016, 02:52:34 AM »

.... for some reason my low reed played on two of my high notes even though I had it turned off.  I turned the low reed on and then turned it off again and those two notes played normally afterwards... weird.   
It sounds like a misalignment between the block and pallet holes and/or a sticking slider.
You will have to ensure that everything is lined up properly.

..  Is it OK to have straps added to an antique accordion?
It is but don't do anything drastic yet. You may not need to do that at all.
First thing to do is check that the air holes in the blocks are aligned with the holes in the pallet board.

How do I check for this?  I can't see any holes that they might align with.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Change in Outside Row Sound
« Reply #26 on: April 09, 2016, 03:21:11 AM »

The holes are hidden from view under the reed blocks.
Loosen that fixing screw I talked about earlier and slide the block so that you get a good fit under the wooden bar that locates it
at the end opposite to the fixing screw. It will only move by millimeters probably.
DO NOT attempt to lift the blocks out. There are sliders under some of those blocks that are easy to damage.
Make sure to re-tighten the screw.
Try that and see if it makes any difference.
Logged

John Cohen

  • Member
  • *
  • Offline Offline
  • Posts: 33
Re: Change in Outside Row Sound
« Reply #27 on: April 09, 2016, 03:32:01 AM »

The lifting screw is the one that's on the side where the tape is, correct?

Thanks for all the help, by the way.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Change in Outside Row Sound
« Reply #28 on: April 09, 2016, 03:47:31 AM »

The lifting screw is the one that's on the side where the tape is, correct?

It's on the left here in your own photo.
Logged

John Cohen

  • Member
  • *
  • Offline Offline
  • Posts: 33
Re: Change in Outside Row Sound
« Reply #29 on: April 09, 2016, 03:52:28 AM »

Oh, you mean those four screws on the left with the little hinges that hold things in place.

Once I loosen them, you want me to push the blocks to the left to make sure they are tight?
Logged

The Blues Viking

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
Re: Change in Outside Row Sound
« Reply #30 on: April 09, 2016, 03:59:31 AM »

How far are you from Philadelphia? I bring my boxes to Liberty Bellows in South Philly and think they do good work.

I'm in Baltimore.  While it's close to Philly it can take an entire day to drive there and back with traffic.

"The Button Box" is nearer you, in Maryland in fact. (Sunderland) They've got a pretty good rep but I've never dealt with them.

http://www.buttonbox.com/

TBV
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Change in Outside Row Sound
« Reply #31 on: April 09, 2016, 04:01:48 AM »

Oh, you mean those four screws on the left with the little hinges that hold things in place.

Once I loosen them, you want me to push the blocks to the left to make sure they are tight?

To make sure that the air holes in the blocks and the pallet board (which you can't see) are aligned properly.
Logged

John Cohen

  • Member
  • *
  • Offline Offline
  • Posts: 33
Re: Change in Outside Row Sound
« Reply #32 on: April 09, 2016, 04:03:08 AM »

How far are you from Philadelphia? I bring my boxes to Liberty Bellows in South Philly and think they do good work.

I'm in Baltimore.  While it's close to Philly it can take an entire day to drive there and back with traffic.

"The Button Box" is nearer you, in Maryland in fact. (Sunderland) They've got a pretty good rep but I've never dealt with them.

http://www.buttonbox.com/

TBV

The Button Box is in Massachusetts and has a 10 week wait for repairs. 
Logged

The Blues Viking

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
Re: Change in Outside Row Sound
« Reply #33 on: April 09, 2016, 04:24:16 AM »

The Button Box is in Massachusetts and has a 10 week wait for repairs.

I really should learn to look at a map once in a while.
Logged

John Cohen

  • Member
  • *
  • Offline Offline
  • Posts: 33
Re: Change in Outside Row Sound
« Reply #34 on: April 09, 2016, 04:38:12 AM »

Oh, you mean those four screws on the left with the little hinges that hold things in place.

Once I loosen them, you want me to push the blocks to the left to make sure they are tight?

To make sure that the air holes in the blocks and the pallet board (which you can't see) are aligned properly.

I just finished with this... it may have made it a tiny bit better, or I may just be going crazy at this point.  It's not how it was before I started this mess.   :(
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Change in Outside Row Sound
« Reply #35 on: April 09, 2016, 10:54:29 AM »

I've read this thread with increasing puzzlement.   It is one of those things that are frustrating to deal with at a distance like this, but put the box in the hands of a good tech person and the problem will probably reveal itself in a few minutes.

Looking at this logically you have not disturbed the reed blocks before this change happened so for the moment I'm assuming that the reed blocks are in the correct position.   

I think the significant clue is the brief problem you had with the coupler operation.  If a coupler slide does not close completely then some air will pass through the low reed as each note is played.   This can be insufficient to make the low reeds speak, but high reeds need significantly less air and may sound when the coupler slide is not quite closed.  A nut and washer loose inside the box could conceivably get in a position to prevent the full movement of the coupler mechanism.   You did say that you had recovered a nut and washer, but it is possible that there might have been a second washer, or even a second nut, that are somewhere in there blocking the full movement of the coupler.  A partially open coupler slide could also affect the sound of the other reeds by bleeding off some air.  It's not all that easy to check the operation of the slides but the simplest is to remove the treble grill, hold down a button on the outside row to lift a pallet and operate the coupler switch.   See if you can see the slide moving in one of the holes under the pallet.   Look from both sides of the pallet and look for a gap at one side when the hole should be closed.

Of course it could be something else!

Good luck!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

DaveCottrell

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Change in Outside Row Sound
« Reply #36 on: April 09, 2016, 11:57:42 AM »

PM Sent.
Logged

John Cohen

  • Member
  • *
  • Offline Offline
  • Posts: 33
Re: Change in Outside Row Sound
« Reply #37 on: April 09, 2016, 03:58:23 PM »

I've read this thread with increasing puzzlement.   It is one of those things that are frustrating to deal with at a distance like this, but put the box in the hands of a good tech person and the problem will probably reveal itself in a few minutes.

Looking at this logically you have not disturbed the reed blocks before this change happened so for the moment I'm assuming that the reed blocks are in the correct position.   

I think the significant clue is the brief problem you had with the coupler operation.  If a coupler slide does not close completely then some air will pass through the low reed as each note is played.   This can be insufficient to make the low reeds speak, but high reeds need significantly less air and may sound when the coupler slide is not quite closed.  A nut and washer loose inside the box could conceivably get in a position to prevent the full movement of the coupler mechanism.   You did say that you had recovered a nut and washer, but it is possible that there might have been a second washer, or even a second nut, that are somewhere in there blocking the full movement of the coupler.  A partially open coupler slide could also affect the sound of the other reeds by bleeding off some air.  It's not all that easy to check the operation of the slides but the simplest is to remove the treble grill, hold down a button on the outside row to lift a pallet and operate the coupler switch.   See if you can see the slide moving in one of the holes under the pallet.   Look from both sides of the pallet and look for a gap at one side when the hole should be closed.

Of course it could be something else!

Good luck!

Thanks for your help- I'll check this.  I don't think there are any other missing nuts or washers... the two I recovered match the other two that are installed on the other side of the box, so I'm not missing any parts.
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal