Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Noisy valves  (Read 2404 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Noisy valves
« on: November 10, 2016, 12:20:03 PM »

I have a few noisy valves on the lowest notes of the bassoon (L) reeds. One in particular is quite noticeable, and it appears to be the lowest bassoon reed that uses plastic. Even just reducing the noise on this one would be enough of an improvement. I've attached a photo - you can see the first bassoon reed to use plastic five in from the left. What are my options for reducing or eliminating the noise?
Logged
C#/D player

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Noisy valves
« Reply #1 on: November 10, 2016, 12:34:41 PM »

Apart from adjusting the tappet clearances, how about a leather valve; softer surely means quieter?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves
« Reply #2 on: November 10, 2016, 12:37:29 PM »

Edward is correct.  Leather valves are quieter.
But the remaining question is which valve.  The one you can see, or the one underneath?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Noisy valves
« Reply #3 on: November 10, 2016, 01:15:31 PM »

I have a few noisy valves on the lowest notes of the bassoon (L) reeds. One in particular is quite noticeable, and it appears to be the lowest bassoon reed that uses plastic. Even just reducing the noise on this one would be enough of an improvement. I've attached a photo - you can see the first bassoon reed to use plastic five in from the left. What are my options for reducing or eliminating the noise?
Leather valves are generally quieter than plastic (vinyl) valves. Having said that, the plastic valves on the mid-range and higher reeds are usually fine.

I would say there are three sorts of noises which valves might make:

1. A slight slapping or clicking noise as the valve clicks shut against the reed plate. Usually audible on the start of a note in a particular bellows direction. Sometimes the offending valve can be seen to be slightly bowed or raised. But sometimes nothing is particularly visible. The remedy is to replace the offending valve.

If the click occurs on a pull note, and/or there is a sudden increase in volume or change of pitch soon after the note starts sounding, it may be that its partner valve on the inside of the reed chamber is fouling the side or end of the chamber walls which will delay the valve acting properly and immediately. Replacing the valve ensuring that it does not contact the chamber walls is the remedy. Sometimes you may need to trim a fraction off the valve length and/or ensure the chamber walls are smooth with no rough wood splinters which can catch on the valve. 

2. A transient rasping or rattling noise heard at the start of a bellows direction change. This usually affects the larger, lower pitched reeds more than the higher ones.  The cause is usually a bowed or bent valve, sometimes bowed in the middle. Remedy - replace the valve, possibly changing a vinyl valve for a leather one, but normally just renewing it does the trick.

3. A low-pitched fluttering noise, sometimes encountered on the lowest bass notes. The pitch of the flutter can be the same as or an octave lower than the reed itself. The cause may be (i) the adjacent valve to the reed in question starting to vibrate in resonance with the reed tongue. Sometimes replacing the valve with one which has stronger vinyl leaves or fixing a stronger wire spring will do the trick by holding the valve more tightly to the reed plate.

Alternatively, (ii) on the very lowest bass notes, particularly those with weighted brass tips, the amplitude of swing of the reed tongue can be so large that the reed tongue tip comes into contact with its valve. This usually becomes apparent a second or two after the note has started sounding, as the reed tongue builds up amplitude.  This is more difficult to remedy, but replacing the valve with less glue at the rivet end may allow the valve to open more fully and avoid contact with the reed tongue.

In all cases, bear in mind that replacing a valve may slightly alter the tuning of the reed so you need to check and adjust the tuning if necessary, after replacing any valve.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Noisy valves
« Reply #4 on: November 10, 2016, 01:42:21 PM »

I would describe the sound as a slight gurgling/rattling noise during a change in bellows direction. It only occurs on the lowest few bassoon notes and just a tad on the lowest notes of the middle reeds. It is most apparent on the lowest bassoon reed that uses a plastic valve. The valve appears to be perfectly flat and there are no other sounds or problems associated with it that I can detect.

I've never done anything with reed valves before, and I'd rather not get into anything that would noticeably change the tuning of the instrument (I haven't the means or knowledge to adjust tuning).  However, if it is possible for a novice to replace the one valve (that is showing) with something quieter, I would be willing to give it a go. Should I order some leather valves from someone? And is it as straightforward as peeling off the old one and gluing on a leather one?

It's interesting to note that I played another box that was the exact same model and key, and I got the same valve noise on the same key, which makes me think it's a design issue with the use of the plastic valve starting on that particular note.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves
« Reply #5 on: November 10, 2016, 01:51:57 PM »


It's interesting to note that I played another box that was the exact same model and key, and I got the same valve noise on the same key, which makes me think it's a design issue with the use of the plastic valve starting on that particular note.

Plastic valves in good condition on low reeds do make a noise on change of bellows direction.  That is normal. You will probably not notice it much in normal play.

The only way to stop or reduce the noise is to replace the plastic valves on those reeds with leather valves, which means taking the reeds out to change the underside valve as well as the one you can see.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Noisy valves
« Reply #6 on: November 10, 2016, 01:59:47 PM »

It's noise that I've not noticed before on similar boxes, which is what prompted me to open it up and look inside.  I intend on continuing to play it as is for now, but it's certainly something I notice!

If I only replaced the valve that is showing, would it not at least reduce half the noise? ::)
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves
« Reply #7 on: November 10, 2016, 02:02:00 PM »

Probably, but it's not something I've tried.  I don't like half done jobs! ;)
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Noisy valves
« Reply #8 on: November 10, 2016, 02:16:29 PM »

Booster springs on leather valves do help. I had a persistently noisy (new) valve on a PA recently. The flat booster Spring still didn't help, but then I put a tiny kink in it near the base, with watch maker's pliers, causing it ever so slightly to push onto the valve, and this solved the problem.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Noisy valves
« Reply #9 on: November 10, 2016, 05:23:30 PM »

If weight upon the valve is the issue, is there any way to add some weight/tension to the existing plastic valve? Or should I just go with leather....

Looks like the leather valves don't have any springs on them either, just another layer of plastic....
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves
« Reply #10 on: November 10, 2016, 05:40:34 PM »

And the strength of helper spring that's required is less on smaller size valves. Getting valves to behave properly is one of those aspects of box repair that rely on experience and trial and error, so I don't believe anyone can give you a definitive answer without having the box in front of them. I must have installed thousands of valves and I still expect to get an occasional valve that looks perfectly ok, but doesn't behave as expected.  Sometimes a fresh valve of the same type cures it, sometime a different type, sometimes adding a helper spring, or adjusting a spring for more or less pressure.  In your case, from your description of the sound I don't think there is any defect in the valves, you are just getting the normal sound of a larger sized plastic valve.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Noisy valves
« Reply #11 on: November 10, 2016, 07:02:12 PM »

Thanks for all that info. I also believe that there is no defect, just a "normal" valve noise...the difference is I've played many 4-stop boxes and this is the first time I've noticed these sounds on the lower bassoon notes.
Logged
C#/D player

Peter Courtney

  • Member
  • *
  • Offline Offline
  • Posts: 11
Re: Noisy valves
« Reply #12 on: November 13, 2016, 10:21:50 AM »

I just wonder if your plastic valves are the correct type, should be triple layer. The ones I use from CGM have the outer layer going almost the entire length of the reed. I note yours are not like that. Each month I re valve one or two accordions and have no trouble with the type I use. Yes they are a little noisier, but if you want fast action notes I don't think you can beat them.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal