Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Detached Pallet on a 1040  (Read 1644 times)

0 Members and 1 Guest are viewing this topic.

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Detached Pallet on a 1040
« on: April 26, 2019, 01:50:03 PM »

Afternoon all

Whist playing a rather vigorous version of Oyster Girl for a longsword practice my box started making rather a strange noise (I suspect the tune had nothing to do with it...). Having finally got round to taking the bass end off one of the bass pallets has become detached from its lever. On inspection they appear to have been waxed in. Am I correct?
What's the best way to reattach it Superglue? Wax? Blue Tac? (one of these may be in jest...)

Cheers m dears
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Detached Pallet on a 1040
« Reply #1 on: April 26, 2019, 02:12:28 PM »

Not usually waxed.  Usually adhesive with a circle of white cloth.  The type of adhesive has varied over the years.  You could use wax,  but that would preclude later use of adhesive.  Hot melt glue works well, or cut a piece of cotton cloth and press it on with a bit of pva.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Detached Pallet on a 1040
« Reply #2 on: April 26, 2019, 02:23:13 PM »

I don't know about Hohners ...but on my Casali PA the pallets are fixed with wax and the joint covered by a leather patch.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Detached Pallet on a 1040
« Reply #3 on: April 26, 2019, 02:38:01 PM »

Not usually wax, as Theo has said. A dab of glue from a hot glue gun will do the trick.

I’ve noticed that the Beltuna one-rows use wax to affix the pallets to the arms, at least on the ones I’ve seen.. I thought it an odd choice.
Logged
C#/D player

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Detached Pallet on a 1040
« Reply #4 on: April 26, 2019, 02:48:09 PM »

If the wax is as sticky as that which Mr Marshall sells, it'll be as good s any glue!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Detached Pallet on a 1040
« Reply #5 on: April 26, 2019, 02:51:01 PM »

Quote
I’ve noticed that the Beltuna one-rows use wax to affix the pallets to the arms, at least on the ones I’ve seen.. I thought it an odd choice.

Wax would be odd for a Hohner but it's often seen on Italian boxes.
Logged

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Detached Pallet on a 1040
« Reply #6 on: April 26, 2019, 03:30:26 PM »

Thanks all for prompt replies.

To my untutored eye it certainly looks like wax. Perhaps an Italian on work experience in Germany?

Tried to post a picture following usual steps but wouldn't have it for some reason.

Off in search of glue gun...
Logged
On the edge of Cheshire's Golden Triangle, apparently...

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Detached Pallet on a 1040
« Reply #7 on: April 26, 2019, 03:45:35 PM »

Not usually wax, as Theo has said. A dab of glue from a hot glue gun will do the trick.

I’ve noticed that the Beltuna one-rows use wax to affix the pallets to the arms, at least on the ones I’ve seen.. I thought it an odd choice.
I didn’t see wax on my Beltuna, but I wasn’t really picking at what’s holding them on.?
I was repairing the tops of the pallets, the tape feel off for the previous owner and then he painted a red stripe in that spot (finger polish?). I’m not sure if that could be applied over wax?

I put a piece of maple banding over the area.
This banding by itself is a good bond as the top of pallet arm rod is even with top of pallet, so it sticks to a good part of the arm , heat applied by iron.

I found dab of glue and the cloth dot was used on my Hohner 1040 ,so that’s what I did when repairing.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Anne Croucher

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 203
Re: Detached Pallet on a 1040
« Reply #8 on: April 26, 2019, 04:35:26 PM »

If it is wax then it will be easy to remove it from the pallet - a warm butter knife should lift it off - or you might find that the strut can be fitted into its former position and a little warmth to soften the wax will refix it. A hair dryer would do it.
Logged
Barcarole D/G
Hohner Ericas D/G and C/F
Hohner el Rey del Vallenato A/D/G aka 'Elvis'
Hohner Liliput Bb/Eb club layout
Meinel & Herold G C F 3 voice 3 row 16 bass

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Detached Pallet on a 1040
« Reply #9 on: April 26, 2019, 04:43:27 PM »

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Detached Pallet on a 1040
« Reply #10 on: April 26, 2019, 06:07:01 PM »

Many the old PAs I’ve worked on have their RH pallets attached with wax (the proper sticky stuff). I do quite like this because it’s easy to refix/undo etc. and I admit to adopting this as an effective way to attach PA pallets.  I have also seen hide glue used, esp for bass pallets tucked under the bass machine, where you really don’t want them coming loose  (:) A soldering iron releases the glue in this case. I do the blob of PVA and disk of hide or cloth for melodeon pallets. Hot glue is ok but I'm not very good at it and it always ends up looking messy, with whiskers etc. and it looks like I’ve done it in a hurry, even when I haven’t. But that's just me. The main thing is that you or somebody later on can undo it.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Detached Pallet on a 1040
« Reply #11 on: April 26, 2019, 07:44:56 PM »

I admittedly would never use hot glue anywhere where it would be seen (such as exposed pallets).
Logged
C#/D player

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Detached Pallet on a 1040
« Reply #12 on: April 27, 2019, 10:40:29 AM »

I admittedly would never use hot glue anywhere where it would be seen (such as exposed pallets).

Taken on board...fortunately the pallets aren't exposed....
Logged
On the edge of Cheshire's Golden Triangle, apparently...
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal