Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3]   Go Down

Author Topic: Microphones and amplification  (Read 15212 times)

0 Members and 1 Guest are viewing this topic.

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Microphones and amplification
« Reply #40 on: October 21, 2009, 02:30:38 PM »

From my perspective the mix is done by a band member and we don't have a big enough mixing desk for me to have separate inputs for treble and bass and let me play my uke as well. Several gigs we haven't had room for that. So having a single input pickup was important, as the alternative was just to not have my bass amplified.
Sorry should have made myself a bit clearer. My setup has a mic (AKG 416) at each end of the box, and a bodypack pre-amp which takes the separate treble/bass inputs from those two mics but sends out through a single XLR. So it goes premixed into only one channel of the desk (and in my case usually via a backline amp).
From other posts here and and on other threads I think that several other people have a similar setup.
IMO the pros considerably outweigh the cons of this setup, unless you regularly have a trustworthy sound person (with two channels to offer you) and don't use a backline.
One of the cons though is mic range, as also discussed above. When I put the system on my piano accordion I do detect an attenuation across the keyboard. But it isn't fatal there and is negligible on the melodeon.

Hah, I wasn't differing, I was using my own experience to back up your point :P
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #41 on: October 21, 2009, 08:48:31 PM »

I agree that separate outputs are needed for treble and bass.

I agree too. But then the key question is who is responsible for the mix out front, and what does this imply for the kind of setup you want/need.
If you could rely on there always being a sound engineer out front who knew what sound you wanted/needed, and if you were playing primarily through a PA rather than backline, then I guess you would want to send the two channels separately out to the desk. And then you need to figure out what is your favourite affordable set up to achieve this, e.g. two standing mics, two clip-ons with separate pre-amps etc, or a combination of the two.
But for many of us these are pretty big ifs. In most settings I play principally through a backline amp and from there (if necessary) into PA, the latter mixed by me or another band member who has to make their own guesstimate about how its all sounding out front. So given this I'm happy to go with the convenience of a set-up described earlier in the thread, i.e. two AKG clip-ons going into a two-input preamp bodypack where the mix is done locally by me. Works for me. Until I get to be doing stadium gigs anyway.

If the two outputs are kept separate, you can almost always common them up into one channel simply by using a 2-into-1 adapter for the case where you do want a single channel -- like going through a backline amp, or into one channel of a desk.

It's like toothpaste, once the white bit and the stripes are mixed you can't separate them again...

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #42 on: October 21, 2009, 08:55:09 PM »


Just a couple of comments -- the "soft cardioid" pattern has pretty poor rejection of sounds from the sides/rear which will make it more prone to picking up ambient noise and feedback, and it looks like a single treble end mic won't be far enough away to get even pickup -- and if it is, it will be even more feedback prone.

Speaking with my sound engineer hat on, the *last* thing I want with a squeezebox is a single input with combined bass and treble -- you're stuck with the balance and combined EQ the player has set (possibly for the sound they want in the monitors or headphones, which is not usually what you want for FOH), you can't EQ the two ends separately, if you turn up the gain for a solo or a quiet bit and the bass end starts to feed back (it's usually the bass end) you can't do anything except turn the whole thing down, you can't vary the levels of the two ends separately to deal with changes in playing level (at higher volumes you don't usually want the bass end to come up in level as much as the treble end), if they swap instruments the balance is rarely the same -- I'm sure I could think of more problems if I really tried... :-)

And for a "non-professional" solution with a lot of disadvantages, it's pretty damned expensive...

Ian


Perhaps you can suggest a better solution. Because this is what always happens. I get overwhelmed with information, anything I think of buying always ends up seeming like a bad idea, and I end up buying nothing, and having to perform through two stand mikes with wholly inadequate results.

Incidentally, the right hand grill on a Benny is less than 8" long. That doesn't seem like a long distance to pick sound up over. I've been working on the assumption that that probably made it too short to have two mikes on that side without interference. It really is very short.

It's been suggested several times before (including by me) that in most cases the best compromise is a decent (preferably hypercardioid) mic on a low stand for the treble end placed about a foot away, and a good quality gooseneck cardioid clip-on mic for the bass end maybe half this distance away.

If you only play one small box like the Benny then a second gooseneck mic for the treble end will work so long as you can get it far enough away to get even coverage, which tends to mean a longer gooseneck than most of them have. If you play several boxes and swap between them of they're a lot bigger this won't work so well, a stand mic is by far the best choice in this case.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #43 on: October 21, 2009, 09:10:46 PM »

Quote
Perhaps you can suggest a better solution. Because this is what always happens. I get overwhelmed with information, anything I think of buying always ends up seeming like a bad idea, and I end up buying nothing, and having to perform through two stand mikes with wholly inadequate results.

I have much sympathy with you, vielleuse, as I'm no sound engineer either.  Isn't the root of the problem that there isn't yet a really good answer available for miking boxes, and we're all compromising, without there being a consensus?

I looked at the pdf 'technical' document that you can read about the K&K system, and it seems to me anyone buying one can't tell in advance how much drop in signal you would get between a reed 2/3cm away from the mike, and one at the end of the keyboard (perhaps about 10/11cm away on your box?)  There's a polar diagram, but in the absence of a scale, and having only one pattern, you can't even estimate what the drop-off will be.  But from the response from the back of the mike, it certainly looks as if feedback could also be a problem, as IanD has pointed out. 

Ian, can you help us at all?

(Erm, this may be heresy, but do close miking systems for boxes actually work properly yet?  The more I understand about their inherent problems, the more I'm reaching the conclusion that they have some way to go.)



I've never come across a commercial close-mic system for the treble end that works as well as a single stand mic, physics is against you. I did try out the idea of a large number of high-quality miniature unidirectional electrets placed under the treble end grille, each close enough to pick up just the reeds closest to it -- but you need a lot of mics (around 10 or more) and they have to be very close to the pallets to prevent cancellation, which means under a close-fitting grille, so you need to fit them individually to every box you play since they can't be swapped over.

Nobody's likely to do this commercially, it costs a fortune and you need to physically modify every box you play. And the mics are so close to the pallets that you get a lot more action noise from them than a mic further away.

So I don't think it's that they've got some way to go, I think the inherent disadvantages can't easily (or even with difficulty) be overcome.

Before anyone says "I've heard a *** close-mic system and it sounded fine", try playing a scale up and down the keyboard and listening carefully for volume and tonal changes which aren't there, or uneven volume along the rows. I guarantee you'll find them.

Of course if these imperfections don't bother you and the sound is "good enough", then by all means use such a system :-)

It's not just close mics on boxes that have this problem, the same issues apply to saxes (sound comes out through the sound holes not just the bell), fiddles (sound close to the body and strings is totally different from far away), guitars (body resonances and string noise are emphasised). One of the few instruments which does work well with a close mic is the recorder, one close to the fipple is all you need for a brilliant sound -- not that surprising given that there's no resonant body and this is where almost all the sound emerges from.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Microphones and amplification
« Reply #44 on: October 21, 2009, 09:29:23 PM »

The point regarding uneven sound and tonal differences is very valid but it must be put into context of usability, durability and feedback resistance. When your playing through some grotty venue PA where you can barley tell the difference from a fiddle and a melodeon, let alone different mics on an expensive box, it all becomes a bit academic. Perhaps I just need to play more upmarket gigs?
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #45 on: October 21, 2009, 09:49:08 PM »

The point regarding uneven sound and tonal differences is very valid but it must be put into context of usability, durability and feedback resistance. When your playing through some grotty venue PA where you can barley tell the difference from a fiddle and a melodeon, let alone different mics on an expensive box, it all becomes a bit academic. Perhaps I just need to play more upmarket gigs?

Maybe so -- I did say that if clip-on mics worked for you and you were happy with the sound that's fine, they can be very convenient. But the question was asked as "what's the best way of micing up a melodeon", so that's what I answered -- wearing my sound engineer hat, like I said... :-)

Regarding feedback resistance, a properly positioned hypercardioid stand mic is *miles* better than a clip-on, if only because it doesn't move around with the player (turn around or walk in front of monitor or put box down on floor ### HOWL ###). With TCB I can have my right hand loud enough in the foldback to hear clearly over a full drum kit three feet to my left and seven other instruments and I *never* have any feedback problems.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

vielleuse

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: Microphones and amplification
« Reply #46 on: October 22, 2009, 08:39:09 AM »

a decent (preferably hypercardioid) mic on a low stand for the treble end placed about a foot away, and a good quality gooseneck cardioid clip-on mic for the bass end

Can you give specific examples of such mikes?

Incidentally I'd still be inclined to prefer a right hand mike mounted on the instrument for various reasons, eg to reduce clutter on stage (there are 5 of us in current band and it can be a squeeze), so I don't have to be conscious of where I am in relation to the mike, and to be certain I have all the necessary bits and pieces for every gig without having to lug a mike stand round with me.
« Last Edit: October 22, 2009, 08:44:02 AM by vielleuse »
Logged

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Microphones and amplification
« Reply #47 on: October 22, 2009, 10:46:10 AM »

Quote
I've never come across a commercial close-mic system for the treble end that works as well as a single stand mic, physics is against you.

Ian, many thanks, your advice has clinched it for me.  This leaves a couple of questions - if you use a LH side close mike, is it really the case that the sound is OK?  The bass reeds are often quite along way apart, too, aren't they, even on 8 bass models?  And, if you use stand mikes, what would be your recommendations on spacing, alignment, feedback problems, etc?

To those who say they are happy with close miking RH systems, that's fine if they are happy with a sound that is altered significantly from the original acoustic sound (and of course many musicians strive for variety in their sound, there's nothing wrong with that).  However the worry I think I would say again is that the box player is unlikely ever to hear what he/she sounds like at the front of house, because he is being swamped by the real sound of his own box when he is playing, and unless he is lucky enough to have a sound engineer, and a really good one too, no one is likely to understand the sound of a box enough to be able to tell him.  Many of us are probably blissfully unaware of the weird sound we are sending out from the stage!

It has always seemed to me (doubling as the box player and the guy with the mixer), that there is a lot to be said for having a simple separate (radio?) system that picks up the FoH sound from the middle of the hall, and shoves it straight back to some headphones for me.  Obviously, you couldn't monitor the overall level, but it would help with an awful lot of other balance and tone settings.  Does anyone use such a device, and are there commercial ones out there, does anyone know? 

In fact, here's the idea in more detail:  The device has two hooks and strings to suspend it from suitable points in the ceiling pointing towards the FoH speakers in the hall about 5-10m in front of them.  It consists of a Zoom H2 with its monitor socket plugged into a high quality radio transmitter with range just enough to reach the (double or single) active background noise suppressing radio headphones that I would use.  In fact, better still, everyone in the band has some similar headphones, then I'll throw away the monitors and forget monitor feedback problems for ever!  And, whoopee, they can adjust their own monitor levels!  Everything is powered by rechargeable NiMH batteries, which are topped up before every gig, to do away with long cable runs.  You could even record every gig, for post mortem purposes!

I can think of one possible snag, and that is the sound delay - I have noticed while using a radio transmitter while playing bass that if you go more than about 10m from the speakers, the sound delay becomes noticeable, and it's off-putting, and difficult to keep rhythm.
Logged

jb

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 250
Re: Microphones and amplification
« Reply #48 on: October 22, 2009, 10:57:38 AM »

However the worry I think I would say again is that the box player is unlikely ever to hear what he/she sounds like at the front of house, because he is being swamped by the real sound of his own box when he is playing, and unless he is lucky enough to have a sound engineer, and a really good one too, no one is likely to understand the sound of a box enough to be able to tell him.  Many of us are probably blissfully unaware of the weird sound we are sending out from the stage!
backline
Logged
there ain't no such thing as a free reed

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Microphones and amplification
« Reply #49 on: October 22, 2009, 11:03:58 AM »

Quote
backline

Really?! You have found that works successfully with a close-mike system?  Or indeed any miked set-up?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Microphones and amplification
« Reply #50 on: October 22, 2009, 12:07:30 PM »



It has always seemed to me (doubling as the box player and the guy with the mixer), that there is a lot to be said for having a simple separate (radio?) system that picks up the FoH sound from the middle of the hall, and shoves it straight back to some headphones for me.  Obviously, you couldn't monitor the overall level, but it would help with an awful lot of other balance and tone settings.  Does anyone use such a device, and are there commercial ones out there, does anyone know? 

In fact, here's the idea in more detail:  The device has two hooks and strings to suspend it from suitable points in the ceiling pointing towards the FoH speakers in the hall about 5-10m in front of them.  It consists of a Zoom H2 with its monitor socket plugged into a high quality radio transmitter with range just enough to reach the (double or single) active background noise suppressing radio headphones that I would use.  In fact, better still, everyone in the band has some similar headphones, then I'll throw away the monitors and forget monitor feedback problems for ever!  And, whoopee, they can adjust their own monitor levels!  Everything is powered by rechargeable NiMH batteries, which are topped up before every gig, to do away with long cable runs.  You could even record every gig, for post mortem purposes!

I can think of one possible snag, and that is the sound delay - I have noticed while using a radio transmitter while playing bass that if you go more than about 10m from the speakers, the sound delay becomes noticeable, and it's off-putting, and difficult to keep rhythm.

There is a much simpler solution,  have a clip on radio mic on your box, then you can wander round the hall as you sound check.  I even know one box player who does this and wanders round the floor playing during the dance!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

jb

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 250
Re: Microphones and amplification
« Reply #51 on: October 22, 2009, 12:20:16 PM »

There is a much simpler solution,  have a clip on radio mic on your box, then you can wander round the hall as you sound check.  I even know one box player who does this and wanders round the floor playing during the dance!
I also now go wireless from my bodypack preamp into wherever (backline). I use an AKG SO40 which is a small transmitter that plugs straight into the XLR output. You can't get them anymore in UK but there are a few online suppliers in europe, mostly Germany.
Logged
there ain't no such thing as a free reed

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Microphones and amplification
« Reply #52 on: October 22, 2009, 12:22:05 PM »

Ah, jb, I take your point, although I would be surprised to hear that you could get all that much to your ears through a backline system with a close mike set-up, without feedback.  Are you perhaps talking about a smallish band, with you taking the lead?
 
I have also played bass for many years through a backline amp.   If you are playing with a mainly acoustic band, the trouble is that the rest of the band, particularly those further away on stage, then complain that they can't hear you, although the bass is blasting out into your own ears.  It seems to me the trick is to position the bass cab in such a way that enough comes out the front for the audience, and you can still hear enough of what you are doing, and you just have to reassure the rest of the band that it is all right, really.  What I have found is that it is easy to get into a situation where you feel you are playing much too loud, but the audience can't actually hear you.  This is not ideal.  I would guess that you get similar problems with a backline system for the box, but without the benefits conferred by having a DI instrument?
Logged

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Microphones and amplification
« Reply #53 on: October 22, 2009, 12:31:11 PM »

Quote
There is a much simpler solution,  have a clip on radio mic on your box, then you can wander round the hall as you sound check.  I even know one box player who does this and wanders round the floor playing during the dance!

I understand the idea, and I'm sure it's a good compromise, but can I suggest that there are certain flaws in the concept?:

1.  A box makes a lot of noise (OK, except mebbe a Streb).  If its player is sound checking while playing it, he or she is inevitably going to be confused by the acoustic sound he/she is hearing into thinking that's what the audience is hearing.

2.  All the downsides of close miking still apply!
Logged

jb

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 250
Re: Microphones and amplification
« Reply #54 on: October 22, 2009, 12:58:50 PM »

All the downsides of close miking still apply!
If you mean range/attenuation then yes I agree. This is an issue. But it's precisely this that makes possible a reasonable backline sound without feedback, and therefore good information on what your mics are picking up and on your treble/bass mix.
All pros and cons. Each to his/her own. Etc.
« Last Edit: October 22, 2009, 02:41:43 PM by jb »
Logged
there ain't no such thing as a free reed

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Microphones and amplification
« Reply #55 on: October 22, 2009, 03:12:25 PM »

Quote
There is a much simpler solution,  have a clip on radio mic on your box, then you can wander round the hall as you sound check.  I even know one box player who does this and wanders round the floor playing during the dance!

I understand the idea, and I'm sure it's a good compromise, but can I suggest that there are certain flaws in the concept?:

1.  A box makes a lot of noise (OK, except mebbe a Streb).  If its player is sound checking while playing it, he or she is inevitably going to be confused by the acoustic sound he/she is hearing into thinking that's what the audience is hearing.

2.  All the downsides of close miking still apply!

All true, but if there is any conclusion to this thread it is that there is no ideal solution for micing a box in a live band,  I'm just suggesting another option, complete with its own set of compromises/limitations.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Microphones and amplification
« Reply #56 on: October 22, 2009, 08:31:27 PM »

Quote
All true, but if there is any conclusion to this thread it is that there is no ideal solution for micing a box in a live band,  I'm just suggesting another option, complete with its own set of compromises/limitations.

Wise words IMO, Theo! 

My original idea in starting this thread was to see if there was any consensus, or lessons emerging.  I have found all the contributions really useful, without exception, and I also believe it has definitely taken us forward.  That's what melnet is all about!
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #57 on: October 23, 2009, 08:33:34 PM »

a decent (preferably hypercardioid) mic on a low stand for the treble end placed about a foot away, and a good quality gooseneck cardioid clip-on mic for the bass end

Can you give specific examples of such mikes?

Incidentally I'd still be inclined to prefer a right hand mike mounted on the instrument for various reasons, eg to reduce clutter on stage (there are 5 of us in current band and it can be a squeeze), so I don't have to be conscious of where I am in relation to the mike, and to be certain I have all the necessary bits and pieces for every gig without having to lug a mike stand round with me.

I use an AKG D3900 for the treble end (many years old now, there are many similar newer mics ) and a Beyerdynamic Opus 82 Set for the bass end

http://www.dv247.com/microphones/beyerdynamic-opus-82-set--58496

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses
Pages: 1 2 [3]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal