Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Do you have to use a tuning table?  (Read 2659 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Do you have to use a tuning table?
« Reply #20 on: September 15, 2022, 12:05:10 PM »

I am still learning but I hope this helps a bit.  I tuned and declubbed a Hohner Modell 1 fairly early on using this method and it worked well for me.  Great tone. I gasketed rather that waxed to allow ongoing fine tuning.  I still use the same method even when waxing.

Method Phase 1:

I found its best to tune in two phases especially when shifting from A435 to A440. I initially tune “on” the block using a simple tuning table. 

I remove the reeds, fully strip, clean and "set" the reeds. I then fit the valves (I tend to use the thin ones now not leather and this makes things easier).  I also clean and prepare the block.  I then use the block on my table to sound the reed by holding the reed in place with my thumb at the top (see photo below). Most blocks seem to have a ridge at the bottom which helps retain the reed on the block face when you do this. I then tune the pull and push reeds incrementally to hit their targets.  I do this by removing and placing flat on the edge of the table to file. Then replacing and re-sounding. Gradually landing on the target.  This makes it a quick easy process. As mentioned elsewhere I use 400grit diamond files to adjust as I find these better in terms of protecting the reed (You keep the old ones and use them for fine tuning).  I then tack wax the reed onto the block or if I am gasketing I pop in the retaining screws.  I do the tremolo base side of the block first to the pure A440 tone.  I then tune the matching reed on other side to the base tone plus the tremolo offset.  I do this in Hz.  I take the base side pure (actual) Hz figure and say add 2 HZ to give 2 beats per sec.  Once both reeds are set I shift over my table to sound the two reeds together (I remove the mask - see photo) and count the beat rate.  I then fine adjust to hit the target beat rate (usually by ear but I sometimes use the Bill Farmer tuner to let me see the visual). Once this its done and I am happy with the note(s), the attack of the reeds and the beat rate I move on to the next pair.  Once I have finished the block I then test down the block to ensure the beat rate is what I want down its length.  I find at this point if things are basically in balance and sounding good or not.  (At this point I usually have to adjust slightly - its an iterative process.). Once the block is in balance I fully wax or fully screw down the gasket reeds.  I must admit I prefer gaskets as it allows you to fine tune more easily on an ongoing basis as the box shifts.
 
This is repeated for each block and the chords (single notes and then chord balance).  Once all this is done it all goes together.  The box though usually plays reasonably well at this point.

As Theo says though this is really pre-tuning. You need Phase 2.

Phase 2:

I have found that things do shift subtlety when the box goes together and I do have to go back in to get things in balance, but for me pre-tuning really helps as it sets a base line to work from.  Nothing beats (excuse pun) playing, testing and fine tuning the box when fully assembled but pretuning can make things easier.

I use the assembled box itself to fine tune I.e. not mounted in any way. I just play it, map adjustments and open it up a lot and tweak. (After reading this topic though I will now make a support and try using the bellows and placing the box end on it. It will be easier.) In this phase I actually remove the reed plates as I'm not confident with using scratchers/files with the reed plates mounted.  It's more work but it suits me.



The reason for posting is to mention that it might be worth considering it as a two stage approach.  Get it somewhere near using the block method above and then refine.  It might help. It helped me.

I will post some pictures of my table later for this pre-tuning (cost about £5). It makes the above method quite quick/easy.  It's worth making one.

Hope that makes sense.  If not just ask  (:).

John

Edit ... photos attached

Note the single hole in the wooden mask on the table for individual reeds (photo) and the mask removed for tremolo (photo) I have other masks for chord and bass blocks. I tune on the edge of the table. See tools.

« Last Edit: September 15, 2022, 05:07:51 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Do you have to use a tuning table?
« Reply #21 on: September 15, 2022, 05:54:36 PM »

That's a honest and humble comment I really appreciate Theo!
And thanks John for the detailed description of the process.

I get it now, realistically anything changing the box affects the tuning, probably thru the subtle changes in air flow/pressure, which I have learned l the hard way. At the end I will need to try and tune it as a whole still.

I taped the other valve when I was tuning and only "blow" on the reed while holding it on the block. Not air tight in any sense, and definitely not the normal bellow pressure/air flow.
I will rig up a tuning table with its bellow and try the first phase. I got enough scrap wood around to do one easily (as long as the wife doesn't realize I am working on a hobby project instead of the house).
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Do you have to use a tuning table?
« Reply #22 on: September 15, 2022, 06:09:41 PM »

(as long as the wife doesn't realize I am working on a hobby project instead of the house)

Watch out there, mind! Hearing the same note sounding every 30 seconds or so might just give the game a way.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal