Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: What next? Repurposing reeds ….  (Read 1463 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
What next? Repurposing reeds ….
« on: November 09, 2022, 10:40:44 AM »

I wandered in to a house clearance warehouse yesterday. It was hanging from a hook in the ceiling by its straps and I though “I bet there is a lot of reeds in that”.  I asked the price, negotiated a bit and carried it to the car.  I had the vague idea that I could repurpose the reeds via the application of a little solder and/or filing  ::)

A few questions ( in hindsight ::) )

Can you repurpose PA reeds like this easily/effectively by filing/loading and get good response?
Could you possibly get a reed set for a 2 row 2 voice from one of these (it has 4 treble banks)? 
Are the reeds likely to be worth it (they are tapered steel on aluminium with a \  top right)?

 Any advice would be much appreciated before I dive in and do any damage  :D

Thanks

John
« Last Edit: November 09, 2022, 10:46:00 AM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: What next? Repurposing reeds ….
« Reply #1 on: November 09, 2022, 11:30:57 AM »

Yes it’s something that several people here have done.  It’s also an excellent way to learn about reed tuning.  One of the things I’ve learned from repurposing reeds is that you need to get a feel for what you can get away with when it comes to changing the pitch of a reed to a different note.  Here is my potted version:
Most (not all) reeds can go up or down a semitone by filing the tip or filing the lower third.  Some can go further.
Lowering the pitch of low reeds is best done by tip loading. 
Lowering the pitch of high reeds is best done by filing.
In general you can lower pitch more than you can raise it.
Tip loading of medium to high reeds can sometimes make them less responsive.
Filing the lower part of medium to low reeds can make the pitch unstable so it hours flat when loud.

There are more subtleties of course, but that is a start.
« Last Edit: November 09, 2022, 11:44:49 AM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: What next? Repurposing reeds ….
« Reply #2 on: November 09, 2022, 03:06:02 PM »

Looking at a typical diatonic row the middle buttons have note pairs that are close enough to each other to be obtained by filing/loading up or down a semitone.  However the notes are further apart on the end buttons.  My guess is it's not a problem for low notes where there is a lot of metal to play with, but could be more tricky if not impossible for high notes.

For example, the 2 top buttons of each row on a DG: F#/C#, A/E, G/E, B/F#
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: What next? Repurposing reeds ….
« Reply #3 on: November 09, 2022, 03:45:00 PM »

Yes, I have done this quite a bit, with excellent results.  As Theo says, you have to use your best judgement to determine how much raw material you have to work with in terms of removing metal to raise/lower pitch.  What's nice about PA reeds is they are often (but not always) a longer scale length than diatonic reeds, which sometimes means you have more reed/metal to work with.  Longer scale reeds can also be a little more responsive - playing sweetly at a very low pressure and building gradually, which I like very much.

Generally, to make diatonic reeds from PA reeds, I will split the difference between pitches.  For example, if I want a D/E reedplate, I would take an D# reedplate from a PA and tune one side down to a D (by filing the base of the reed) and the other side up to an E (by filing near the tip of the reed).  With a good file, this doesn't take long at all and doesn't require much force or effort when filing.  I get them close to the pitch I want outside the box, then fine-tune once installed on blocks and in the instrument.

I only use solder on the higher and lower-pitched reeds when the spread between pitches becomes too great to 'split the difference' on a PA reed by filing alone (for example, a F#/C# reedplate on the high end of a D row)  With lower reeds, I only do it when the reed tips would be weighted anyways.  With higher reeds, it can get a bit tricky.  As Theo mentioned, tip-loading here can result in a loss in reed response.  What you don't want to do is have a big gob of solder on the tip of one of these reeds, as the responsive will most definitely be poor.  In my experience, I've found that having a very small amount of solder spread out over a greater area of the reed tip, then carefully filed down until it becomes barely noticeable that there is any solder there at all (essentially just having marginally increased the thickness of the top portion of the reed tongue) works best.  Setting gap here is crucial, and requires a lot of playing around until you get it just right.  If it's not responding optimally, I just file off all the solder and start again.  It can take a bit of time, but I've been able to produce exceptionally responsive higher-pitched reeds using this method, although it does gets harder the smaller the reed tongues get...

I once created an entire MMM set of reeds for a 2-row accordion by repurposing old, lovely, long-scale PA reeds from a single instrument (I think it may have been a four-voice, so plenty of reeds to work with!).  The results were exceptional, and the end result was a box that was more responsive than the seasoned TAM reeds it originally came with.

« Last Edit: November 09, 2022, 03:51:00 PM by mselic »
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: What next? Repurposing reeds ….
« Reply #4 on: November 09, 2022, 04:03:35 PM »

For the highest reeds which have the greatest difference between push and pull I’ve learned that you can take one reed down a surprising long way four or five semitones for example.  This is what I was hinting at earlier when I suggested learning what you can get away with.

On low reeds it’s obvious at a glance that there is a lot of metal near the tip that can safely be removed.  What is less obvious is that on high reeds there is also a lot of metal that can safely be removed but it’s at the rivet end so the pitch can be lowered much further than you might think. So in the example of mentioned previously of the high F#/C# I would start with a high C, raise on side to C#, and lower the other as far as possible by filing and only add solder to the tip if necessary to get the final pitch.
As I said before it’s a matter of learning by trial and error how far you can go.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: What next? Repurposing reeds ….
« Reply #5 on: November 09, 2022, 04:08:15 PM »

For the highest reeds which have the greatest difference between push and pull I’ve learned that you can take one reed down a surprising long way four or five semitones for example.  This is what I was hinting at earlier when I suggested learning what you can get away with.

On low reeds it’s obvious at a glance that there is a lot of metal near the tip that can safely be removed.  What is less obvious is that on high reeds there is also a lot of metal that can safely be removed but it’s at the rivet end so the pitch can be lowered much further than you might think. So in the example of mentioned previously of the high F#/C# I would start with a high C, raise on side to C#, and lower the other as far as possible by filing and only add solder to the tip if necessary to get the final pitch.
As I said before it’s a matter of learning by trial and error how far you can go.

That's good to know, Theo.  My concern had always been that removing a lot of material at the rivet end of those higher reeds would have resulted in an unstable pitch, so I hadn't gone that route.  I will have to try that out.  Thanks for the tip (no pun intended...)
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: What next? Repurposing reeds ….
« Reply #6 on: November 09, 2022, 04:35:26 PM »

That's good to know, Theo.  My concern had always been that removing a lot of material at the rivet end of those higher reeds would have resulted in an unstable pitch, so I hadn't gone that route.  I will have to try that out.  Thanks for the tip (no pun intended...)

It was a bit of a eureka moment for me. I was led to the discovery by looking at early hohners where the two tongues are the same length even for the very highest reeds where the pieces are a fourth apart, so I reasoned that the high pitch could in theory be brought down to the lower one.

It doesn't even take long to do because the absolute mass of metal to be removed is much smaller than that found on the tip of low reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: What next? Repurposing reeds ….
« Reply #7 on: November 10, 2022, 11:02:34 AM »

Firstly can I say, many thanks for all the replies.  Its a great start for me and I really appreciate it.  Just having a bit of a feel for the extent of possible adjustment is extremely helpful. The concept of using donor reeds between the two required notes is now central in my mind.  Also assessing thickness at both the reed root and tip to inform the best outcome.  I will therefore probably mic up the reeds as I go to see how they vary.  The point made about loading with solder is also well made. I think I have overdone it in the past.

What the posts have mainly done though is focus my mind on what I really want to achieve from this purchase. I've had an idea in mind for a while now.

What I am mainly aiming for is responsiveness at low pressures.  I like playing quietly in chords with low beat rates.  The "feel" of the reeds is what interests me.  The discussion has therefore  really made me think about how to achieve what I want and the careful stepwise process I need to employ.  I will also now go away and check the PA reed lengths.

So.... thanks........ the purchase gets stripped down this weekend  (:).   

The purchase (ex reed blocks/reeds) can then hang on the wall in my workshop .... just looking good.

Any other thoughts on how to deal with the reeds would be extremely welcome.  I think I will strip them all, clean and catalogue first.  I will then map what I want from the new box.

Thanks 

John

PS.  never seen so many "jewels" on a box before ..... (phot below ... last one before it gets stripped) :D


« Last Edit: November 10, 2022, 12:01:54 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: What next? Repurposing reeds ….
« Reply #8 on: November 12, 2022, 10:12:50 AM »

I've tried to do soldering onto tips but the solder didn't stick well.
Which solder is best? The thin thread with resin core? or solid solder and soldering water? I've heard somewhere that the soldering water is corrosive and will keep on eating away the metal.
Do you use a soldering iron with adjustable temperature? Which temperature would be best?
Any advice welcome!
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: What next? Repurposing reeds ….
« Reply #9 on: November 12, 2022, 10:29:12 AM »

Resin cored electrical solder wire is what is required, do not use plumber’s solder and acid flux. Degrease the reed with meths or white spirit on a cotton bud, you could lightly abrade the tip with 400 grit paper or a fine file but I normally don’t. I use a standard 25W soldering iron, heat the tip of the reed with the tinned iron and apply the solder to the reed tip avoiding contact with the iron itself. Remover the solder wire and the iron without disturbing the molten solder and allow it to cool. It’s a bit of a knack and a little practice is needed before you are entirely comfortable with the process.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: What next? Repurposing reeds ….
« Reply #10 on: November 12, 2022, 12:46:47 PM »

Hi Pete, thanks for this information!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: What next? Repurposing reeds ….
« Reply #11 on: November 12, 2022, 12:50:02 PM »

You will need to support the reed while applying the solder with a thin sheet of something slipped under the reed tongue.  I usually use a piece of paper which helps to absorb sone of the surplus flux.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: What next? Repurposing reeds ….
« Reply #12 on: November 14, 2022, 04:34:17 PM »

A busy weekend.  I have now stripped and rough cleaned the reed plates ..... all 230 of them (460 reeds).

First batch in acetone.

Thanks for all the responses.  It has kept me going!

Questions though .... The treble reeds have been cut at an angle at the base. ie. \_/    (see photo)  It's the first time I have seen this.  The bass reeds are from strip (blue edges) but the treble are cut on all faces on the base in a \_/ shape....  My questions are … why? .. and .... are they typical of Italian reeds?

It just seems a strange way to manufacture them.  They are 1920's.  The box is a La Sirena by Emilion Ficosecco

Willem, ...... excuse late reply.  I use electrical solder (pre-fluxed) and as per Theo and Pete I heat the tip, remove the iron and apply the solder.  I use a brass feeler gauge under the tip to support.  Works well without flux.  Hope this helps.

John
« Last Edit: November 14, 2022, 04:51:47 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: What next? Repurposing reeds ….
« Reply #13 on: November 14, 2022, 05:11:45 PM »

That shape of the reed head is something I’ve not see before. Perhaps it was a way for the reed maker to identify their reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: What next? Repurposing reeds ….
« Reply #14 on: November 15, 2022, 01:55:09 AM »

That shape of the reed head is something I’ve not see before. Perhaps it was a way for the reed maker to identify their reeds.

Worked on a few Ficosecco boxes over the years, but I've never seen that shaping either. Intriguing....
Logged
Tuner/repairer, now retired.

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: What next? Repurposing reeds ….
« Reply #15 on: November 15, 2022, 02:38:59 AM »

I've seen that same ornamental file work in nice hand-made reeds from the 1920s, and still have a couple of Baldoni-Bartolis that have it (a piano accordion and an Irish-American box)
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal