Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Placing felt around treble holes on soundboard  (Read 3329 times)

0 Members and 1 Guest are viewing this topic.

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Placing felt around treble holes on soundboard
« on: November 11, 2020, 08:44:58 PM »

I’m working on a project with placing new reedblocks in an older presswood Hohner. Trouble is, the old reedblocks had the felt attached to the bottom, where as the new reedblocks have no felt on the bottom. Anyone have any suggestions as to a best practice for adding felt, either to the soundboard or to the bottom of the reedblock? Cutting the holes is my biggest concern.
Logged
Too many accordions, help!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Placing felt around treble holes on soundboard
« Reply #1 on: November 12, 2020, 01:09:07 AM »

I’m working on a project with placing new reedblocks in an older presswood Hohner. Trouble is, the old reedblocks had the felt attached to the bottom, where as the new reedblocks have no felt on the bottom. Anyone have any suggestions as to a best practice for adding felt, either to the soundboard or to the bottom of the reedblock? Cutting the holes is my biggest concern.

I use large diameter hollow leather punches for jobs like this. Lay the felt on a piece of scrap wood and whack the punch with a hammer. To avoid the felt crinkling, I also ensure the the punch is sharp by using a diamond file or diamond plate to get a sharp edge on the outside taper.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Placing felt around treble holes on soundboard
« Reply #2 on: November 12, 2020, 07:39:06 AM »

When I have done this job in the past I have used Olovisc and applied it to the soundboard. Once it is in place it is a simple, if tedious, job to cut the holes out using a scalpel. This may also require some work to adjust the block clamps as the olovisc will be thinner than the felt.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Placing felt around treble holes on soundboard
« Reply #3 on: November 12, 2020, 08:33:36 AM »

I use the same method as Lester but with a different gasket material, confusingly also called olovisc but a woven fabric with a velvet nap. It cuts much more easily than the self adhesive type.   It’s the same material that is used for reed block gaskets on most Italian boxes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Placing felt around treble holes on soundboard
« Reply #4 on: November 12, 2020, 08:49:50 AM »

I have two way's to do this......#1, place the reed block on the 'bed' of a printer/scanner, most seem to have the function these days, then create a scan.......I then use "Spray-Mount" craft spray on the paper to create a lose bond to the felt ( from the Wool Felt company, if Uk based ).  I found that if I did not temporarily bond the paper to the felt it inevitably moved no matter how careful of 'clever' I tried to be, using fixings of various sorts, ie. tapes/pins etc.  Once bonded, I 'punch' the holes using a generic Chinese/Ebay punch set, but, I keep the edges sharp with finger files inside and out.

#2 is via a 'rubbing' using a sheet of paper and a soft grade pencil.  I make a sharp 'fold' at the edges of the block before starting the rubbing to make sure it doesn't move. 

Again, Spray-Mount, punch etc.  Once the holes are punched the paper lifts away as the bond is superficial.

I find I sometimes need to use a punch one size under the "edge" of the image to get the right dia. hole

Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Placing felt around treble holes on soundboard
« Reply #5 on: November 12, 2020, 09:34:51 AM »

I use the same method as Lester but with a different gasket material, confusingly also called olovisc but a woven fabric with a velvet nap. It cuts much more easily than the self adhesive type.   It’s the same material that is used for reed block gaskets on most Italian boxes.
That's useful to know, Theo.
Do you obtain it from Carini?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Placing felt around treble holes on soundboard
« Reply #6 on: November 12, 2020, 09:41:14 AM »

Yes,  I’ll see if I can get the part number:    I think its 4509
Felt is really a bit to soft for this job
« Last Edit: November 12, 2020, 11:24:21 AM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

xgx

  • Bagpipes & Musette Boxes... and Banjos, luv 'em!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1157
Re: Placing felt around treble holes on soundboard
« Reply #7 on: November 12, 2020, 10:18:47 AM »

has anyone tried the self adhesive craft foam?   It has been used for getting a seal on smallpipe key pads.
Logged
Graham

Socio-Demographic:   Graduate, Coffin Dodger
 Location: N Cambs/S Lincs - UK

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Placing felt around treble holes on soundboard
« Reply #8 on: November 12, 2020, 10:23:11 AM »

Not tried, but like felt it’s a bit on the soft side.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Placing felt around treble holes on soundboard
« Reply #9 on: November 12, 2020, 02:31:58 PM »

If you dont have a scanner you can obtain the same results to make a template using a good old fashioned pencil and tracing , scribbling over the paper over block. Its may be easier to but the material on the fondo rather than the blocks if cutting after , its chicken and egg You most likely wont change again. If push comes to shove a felted block can face a felted fondo but not the other way round :M unfelted block unfelted fondo. Careful with glue as you dont want it inside the blocks or glueing the pallots closed. Self adhesive solves that.Good results can be had with leather chamis  its the thickness that matters most. low tack glue nothing over the top.
Logged
Mark Taylor
Folkloristmark

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Placing felt around treble holes on soundboard
« Reply #10 on: November 12, 2020, 03:08:05 PM »

The "Wool" Felt Company, despite it's name, sells a range of 30%/40% wool/viscose mix and "straight" Polyester Felts in a number of thicknesses which are firm enough to do a good job, in my experience and can be used for pallet/pad work too. 
Logged

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: Placing felt around treble holes on soundboard
« Reply #11 on: November 12, 2020, 04:12:32 PM »

I used Nigel's #1 method (scanning to produce a template and cheap leather punch) to cut the self-adhesive Olivisc to fit onto new reedblocks to fit into an old Erica.
Very straight-forward. Just check orientation of template, olivisc and reedblock before cutting :)
I had considered Lester's option of fixing olivisc to the fondo, but decided against it for two reasons - firstly my other Hohners all have felted blocks, and secondly life's too short to be cutting that many small circles with a scalpel!!
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Placing felt around treble holes on soundboard
« Reply #12 on: November 13, 2020, 05:44:33 PM »

 I basically use FolkloristMark's method. I spray some paper with moveable adhesive and lay it on the item I want to trace. I rub the side of the pencil on it from a couple of directions it do a rubbing. this will clearly show the holes. Peel this and stick it to whatever you are using for a gasket, I found fancy brushed up wool cloth for coats is pretty similar to piano felt.
 Use a punch if you have the right size , or use a round nose wood carving chisel and a small hammer to tap cut the pattern through the felt (this works quite well) this system works for everything from auto water pumps to cutting a steam valve chest gasket on a steam engine.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: Placing felt around treble holes on soundboard
« Reply #13 on: November 14, 2020, 02:16:37 PM »

Thanks for all the replies. I’m going to experiment with as many as I can.
Logged
Too many accordions, help!

Frankal

  • Good talker
  • **
  • Offline Offline
  • Posts: 78
Re: Placing felt around treble holes on soundboard
« Reply #14 on: March 17, 2023, 07:14:40 PM »

placing new reedblocks in an older presswood Hohner. ... the new reedblocks have no felt on the bottom...

Reviving an old thread as I am about to attempt the same and seeking advice on preferred material - olovisc or leather - please.

Looking at either:
olovisc from CGM; or
leather from the accordionary, who are supplying the reedblocks.

Komat, how were your experiments?
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Placing felt around treble holes on soundboard
« Reply #15 on: March 17, 2023, 07:32:09 PM »

placing new reedblocks in an older presswood Hohner. ... the new reedblocks have no felt on the bottom...

Reviving an old thread as I am about to attempt the same and seeking advice on preferred material - olovisc or leather - please.

Looking at either:
olovisc from CGM; or
leather from the accordionary, who are supplying the reedblocks.

Komat, how were your experiments?


Olovisc is my material of choice for this job

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: Placing felt around treble holes on soundboard
« Reply #16 on: March 27, 2023, 11:34:46 AM »

I used olovisc and it worked wonderfully.
Logged
Too many accordions, help!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Placing felt around treble holes on soundboard
« Reply #17 on: March 27, 2023, 01:56:39 PM »

Carini do another type of olovisc which is not self adhesive and is a woven synthetic material with one felted side.  If you have ever looked inside a modern Italian made box you will have seen it under the reed blocks.  I ordered some accidentally years ago when I was first trying to get the adhesive stuff.  It is thicker, easier to cut and more durable than the adhesive stuff.  But if you just have the adhesive olovisc it will work perfectly well.  It's better than felt because its firmer and easier to cut.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal