Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Correcting errors/design choices in an instrument  (Read 1589 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Correcting errors/design choices in an instrument
« on: March 14, 2024, 04:02:12 PM »

I hesitate posting about this on here, but I would welcome some feedback.  A client recently brought an instrument to me that was built by a professional box builder.  The client was looking to have the tuning adjusted, but also to address some issues of poor reed response.  Upon close inspection, I discovered the following:

-reedblocks were very loose on account of poor alignment of the block with the slot/notch the builder had put into the casework which would accept the fastening brace.  There was no way of tightening down the block unless the old slots were filled in and re-done in the proper location and correct size (or some combination of spacers to try and bridge the gap).  This is not a big deal to correct.

-no reedblock gasket, either on the bottom of the block or on the 'fondo'.  It's just the bottom of the block (which is made out of MDF, along with the 'fondo') against a metal plate that houses the slides.  As you can imagine, loose blocks and no gasket will certainly result in poor reed response!

-no wax between reedplates (only wax on the top and bottom).  In some cases, there is absolutely no space whatsoever between plates, and one plate is just pushed up against the next one.  In other cases there is a very small gap, with no wax in the channel.  In the cases where there is wax, it is superficial, meaning that no wax actually makes it to the bottom of the channel to seal between reedplate and block.

-some of the underside valves are too long for the reed chamber. The width of some chambers are also so narrow that the reed tongue and adjacent valve only *just* clear the chamber walls.  Things are as tight as they possible could be!

-the lowest push reeds on the outer block are too close to the bellows frame and make contact with the frame when played with any real gusto..  I can see that the builder already carved out some of the bellows frame to accommodate the travel of these reeds, but it's not enough.  The lowest pull note reeds actually strike the back of the chamber.  I can't move those reeds any further out from the block because they're already striking the bellows frame.  Carving a little more wood out from the bellows frame (there's not much material left there to work with) may mitigate some of the issues with the push reeds.


There's more, but these are the areas that need focusing on before I even think about tuning and adjusting reed gap.  If it were my instrument and time and money were not a factor, I would strip all the reeds (at least the treble reeds) and re-wax properly, change/trim the inner valves that are too long or wide, and look at installing a gasket.  However, for the sake of the client, I'm wondering how much return one would actually get with some of these repairs. Namely:

-reedwax between plates. There doesn't *appear* to be any gap between plate and block, even though there is neither a gasket nor wax sealing this connection. The plate appears to be nailed into place fairly snugly against the block, so I'm wondering if it would be worthwhile to strip all the reeds and wax it back in thoroughly.  Obviously the correct way to do this would be to either use gasket or wax, but the builder used neither.  In place where the reeds are butted up against each other, there would be no room for wax.  My concern with trying to get wax flowing between the narrow space between reeds (as they currently are) is that you'd have to get it quite hot to flow in such a tight space, and with the underside reed tongues and valves only just clearing the chamber walls, the potential for molten wax to seep under there and foul them up is certainly there.  Ideally I would strip them all and then seal each reedplate edge with wax before pushing the adjacent reedplate (carefully!) into place while the wax was still hot.

-installing a gasket of some kind.  I actually don't have any gasket material available (apart from some olovisc, but I'd rather keep that for its intended use) to install, but I'm wondering how much difference it will actually make, given that I will take steps to ensure the block is fastened down securely against the fondo.

Obviously, there is no question about what the proper way is to have done these things in the first place.  What I'm concerned with here now is making the best of a box that was built with some unusual design choices and/or was done in some haste.
« Last Edit: March 14, 2024, 04:31:03 PM by mselic »
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Correcting errors/design choices in an instrument
« Reply #1 on: March 14, 2024, 05:26:55 PM »

I can't speak much about squeezeboxes - I fanny about with them purely to satisfy my own masochistic craving - but I've done a fair amount of guitar work over the years and I've occasionally seen some trainwrecks that, despite being built by "professional luthiers" were showing complete disregard for quality workmanship.

Personally, if I encountered something like this, I'd refuse to work on it, show the customer why (don't put them to sleep by highlighting every inaccuracy - just pick half a dozen most critical issues) and tell them to contact the original luthier for explanation. After all, they've paid a lot of money to buy the box first place. They are not going to pay you the same amount of cash (or more) to fix this box properly, are they?

You won't be popular if you take this route, but imho that's better than spending hours of unpaid work trying to fix someone's botched job. If it's this bad on the outside, there's almost always guaranteed to be even more issues on the inside. As brutal as it may be, but it's a lose-lose scenario for you.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Correcting errors/design choices in an instrument
« Reply #2 on: March 14, 2024, 05:30:05 PM »

That’s a sorry tale of a design that needs to be refined.
I would be tempted to refer the client back to the maker.  If that’s not possible I would deal with the reed block fit first because that is relatively straightforward and should give a noticeable improvement.  If I was in your place I think I would leave it at that but give the client a detailed written description of the remaining negative features.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Correcting errors/design choices in an instrument
« Reply #3 on: March 14, 2024, 05:58:58 PM »

This box has already once been returned to the maker by the client shortly after they initially took receipt of it (having purchased it new from the maker). At that time it was returned on account of the wax being cracked and in poor condition, the cause of which was surmised by the maker as being due to changes in environmental conditions during transit.  The maker re-waxed the reeds and sent it back.  The client lives overseas from the maker, so I believe the client is reluctant to send it back again on account of the high costs of shipping accordions these days.  However, I do agree that the builder should be responsible for correcting these issues.  Mind you, if the builder has already twice signed-off on it now, I'd be concerned that they might not even acknowledge that there is any issue with their instrument.
Logged
C#/D player

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Correcting errors/design choices in an instrument
« Reply #4 on: March 14, 2024, 07:19:35 PM »

With so many issues with this box I would be tempted to suggest to the client that they name the maker on here.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Correcting errors/design choices in an instrument
« Reply #5 on: March 14, 2024, 07:29:20 PM »

With so many issues with this box I would be tempted to suggest to the client that they name the maker on here.

That's a tough line to walk.  On one hand I understand wanting to warn others of the risks of commissioning or buying a box from a particular builder, on the other hand I have no desire to turn this into a witch-hunt or to slag anyone publicly.
Logged
C#/D player

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: Correcting errors/design choices in an instrument
« Reply #6 on: March 14, 2024, 10:29:33 PM »

Did you say the reeds are nailed on along with wax on top and bottom? If so, would it make more sense to remove all the wax and line the reedblocks with olovisc and pin them back on? It wouldn’t require generating space between the plates. I know it’s only a drop in a bucket, but something to keep in mind.
Logged
Too many accordions, help!

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Correcting errors/design choices in an instrument
« Reply #7 on: March 15, 2024, 12:41:56 AM »

Along with the loose or poorly fitting blocks.
This would certainly be a concern
“The width of some chambers are also so narrow that the reed tongue and adjacent valve only *just* clear the chamber walls.  Things are as tight as they possible could be!”

Plus depth of chamber etc. I’d would think?
Working on my recent project the Corso I was dealing with this tight space between the chord reeds. Wasn’t sure how to get the wax in between , I ended up waxing top and bottom with no wax between the plates. Seems pretty tight even without it. I still will try to get some in from the top, but reeds are working fine. Anyway the chambers on the chord and on the treble blocks seem to be about the same.
On a side note when I built my one row I didn’t put wax where the reed plate touches the fondo. Probably should have done the dipped method, but waxing between the plate sides probably seeped over in both directions when it gets to the bottom ( I used the Lester method waxing from the top down).
All the reeds respond well and seem air tight or at least enough. Maybe its better even in that the reeds are in direct contact with the fondo.
« Last Edit: March 15, 2024, 12:50:56 AM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

fc diato

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 146
Re: Correcting errors/design choices in an instrument
« Reply #8 on: March 20, 2024, 03:13:30 PM »

Happy end:
We don't often get the end of the story on the forum, so thought I would append it here. I am said client, and Matt has transformed the box from a rather dull, not very responsive thing that was on the brink of being relegated to 'an expensive dust-gathering mistake' into a living instrument!
Matt did an absolutely fantastic job!

So, if you are in Canada and are having trouble finding a good fettler, I do recommend Matt Selic.



Logged
fc diato
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal