Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed plate inversions  (Read 1784 times)

0 Members and 1 Guest are viewing this topic.

Polkadot

  • Member
  • *
  • Online Online
  • Posts: 26
Reed plate inversions
« on: October 12, 2024, 11:59:42 PM »

Sorry if this has been asked before but I am just beginning my accordion repair journey. I am trying to find out some information about inverting reed plates.
In the attached picture taken from a Youtube clip, the top 6 reed plates on the reed block have been waxed in upside down. The lower 5 plates are in their normal position. Could this approach be used for repurposed pa reeds, where instead of enlarging the reed chamber to allow clearance for the longer reed tongue I would only need to enlarge the chamber for the rivet heads? I have seen plenty of piccolo reeds inverted but not middle reed plates.
Has anyone done this and does it effect the volume or tone?
Logged
HA 114 D G C and A
BC and DG Pokerwork, Double Ray and Double Ray Delux.
Hero D and C

Polkadot

  • Member
  • *
  • Online Online
  • Posts: 26
Reed plates inversions pt 2
« Reply #1 on: October 13, 2024, 12:10:33 AM »

Sorry, this is the second attempt to load the correct picture.
It should show 6 inverted reeds and 5 in the normal position.
 
Logged
HA 114 D G C and A
BC and DG Pokerwork, Double Ray and Double Ray Delux.
Hero D and C

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed plates inversions pt 2
« Reply #2 on: October 13, 2024, 12:14:29 AM »

I e no idea why that’s been done. It’s definitely unusual.  The big disadvantage of reversing reeds like that is that it makes tuning more difficult. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reed plate inversions
« Reply #3 on: October 13, 2024, 08:06:49 AM »

It does, indeed, make reed tuning more difficult. A third of the reeds on my bandoneon are upside-down.  :-\

I am mounting my bass reeds upside down in my current build, as that's the only way I can fit them in, but I found that they are, generally, harder to mount than downside-down, because the reed heel lifts the plate off the reed block a bit, so there's a bigger gap to fill with wax. In my case that's not an issue, as each chamber is cut for a particular reed plate, but in your suggested case of installing longer plates, it might become an issue.
Also, reed blocks tend to be tapered towards the top to leave more space for the reeds and valves to move without clipping the next block. If you have a tightly-packed box, 3-4-5 voices, turning the plates upside down will put them too close together.
« Last Edit: October 13, 2024, 08:09:01 AM by mChavez »
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal