Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed that has been screwed in . . .  (Read 877 times)

0 Members and 1 Guest are viewing this topic.

Matthew B

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 894
Reed that has been screwed in . . .
« on: February 03, 2025, 01:21:03 AM »

A couple of years ago I acquired a Hohner Corona A/D/G from a member of this forum.  It was sold to me at a very reasonable price "as is", and it has provided me many hours of harmless fun. It is badged as from Bells, and may have belonged to a morris player, long ago, as the G row has the bottom four buttons worn into divits. 

I think either one very robust musician or a few folks may have owned it over the years.  It has some very interesting modifications to the standard layout. 

The G bass chord always sounded a bit thin, and recently has begun to sound very sour.  So I pulled the bass end, and discovered a brilliant home-made reed repair (picture attached). I suspect the problem is that the "screwed-in" reed started to sound again, after a long silence.

Questions:
1. How cool is that?
2. Can anyone tell me what the reed combination is for this reed on the G push chord (other picture attached in next post)?
3. Does anyone have a replacement for this reed?  I will pay top dollar!
Logged
Charter Member Presumpscot and Fore River Accordion Club

Matthew B

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 894
Re: Reed that has been screwed in . . .
« Reply #1 on: February 03, 2025, 01:21:34 AM »

Next picture .
Logged
Charter Member Presumpscot and Fore River Accordion Club

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reed that has been screwed in . . .
« Reply #2 on: February 03, 2025, 07:25:47 AM »


Questions:
1. How cool is that?

It's not  :-X

No benefit over riveting apart from the obvious difficulty of aligning it with the slot compared to riveting.
Fitting gaps the size of Grand Canyon at the base of the reed can't be unseen. Possibly, \s a result of alignment difficulties mentioned above.
And what's with the inside-out mounted valve? It must be like underwear - once you worn out one side you just flip it and use it again  >:E

It looks like somebody needed to do a quick repair and they've done it good enough for the moment but at some point it became a long-term solution.

I've had less than successful reed replacements myself and you get to the point where "if it works well enough, it works", but if overall result is worse than original reed, it's really worth going the extra mile and replacing the plate.
« Last Edit: February 03, 2025, 07:30:16 AM by mChavez »
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reed that has been screwed in . . .
« Reply #3 on: February 03, 2025, 02:53:27 PM »

2. Probably you're the best person to find out.

The chord combination is G/D, and there are 3 reedplates associated, with notes G, B, D on the push (outside reeds) and D, F#, A on the pull. The notes on a given plate are usually as close as possible, so one could logically expect to find G/F#, B/A and D/D, but it's probably best to check.

Where the reedplates for these note pairs are located exactly is immaterial as long as they play when the chord button is depressed. Maybe Hohner always puts G/F# in the spot indicated by your red arrow, but maybe they did so only from 1963 to 1969, or someone could have moved things around, etc... so again it's probably best to check. 

If you remove the block and depress the G/D chord button you will see which 3 holes correspond to the chord (1 of the 3 will hopefully be for your funny reedplate).

 On the block, you can gently plink (w. fingernail or small blade) the tip of the 2 other outside reeds corresponding to the G/D chord holes to hear what note they are: if should be any 2 out of G, B or D and the 3rd note, by elimination, is the outside note on the problem reedplate. Since you want to replace that reedplate anyway, remove it from the block and plink the inside reed to find its note, and you the know the combination of notes you need.

Block the hole with Magic Tape and you can keep playing while waiting for a replacement plate. 
Logged

Matthew B

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 894
Re: Reed that has been screwed in . . .
« Reply #4 on: February 16, 2025, 08:08:34 PM »

Thanks Tiropus, that was very helpful.  I tested the two other reed plates in the block harmonica-style with a tuning app, and duly got G/F# and B/A pairs.  The Frankenstein reed, with the bolt through its neck, wouldn't sound.  But it's plate-mate yielded a D, I think. 

In what is probably the least inspiring video ever linked on melnet, here's my test: https://youtu.be/P7h75Ki-bhA.  I'm guessing that a D4 reed pair will not be that hard to source, as they show up on PAs as well as diatonics. 

Further thoughts appreciated.
Logged
Charter Member Presumpscot and Fore River Accordion Club

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Reed that has been screwed in . . .
« Reply #5 on: February 16, 2025, 08:43:46 PM »

you can buy a new one from hohner CS .web site . I use ,de but as you are in america you can get from hohner CS us site. (I would guess)
« Last Edit: February 16, 2025, 08:45:44 PM by folkloristmark »
Logged
Mark Taylor
Folkloristmark
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal