Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 [4]   Go Down

Author Topic: How to efficiently ruin an accordion  (Read 19037 times)

0 Members and 1 Guest are viewing this topic.

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: How to efficiently ruin an accordion
« Reply #60 on: August 28, 2013, 03:09:35 PM »

Theo-
I totally agree that most reeds don’t get polished down through all the manufacturing scratches so the benefit is low. I would state that it is not harming the reed by polishing at the base of the reed. I have examples where the reed broke about half way from tip to root which is not in the area used for tuning so it wouldn't have helped in that case regardless.

Scott
« Last Edit: August 28, 2013, 03:19:58 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: How to efficiently ruin an accordion
« Reply #61 on: August 29, 2013, 06:02:46 PM »

 On the battery unit I use, spin up is less than a second and the volume is less that the reed playing. As the above person noted There are MANY different types of wheels for dremel type devices. I found using the face of a small saucer shaped wheel (not the edge) leaves a very nice finish. It is very difficult to gouge a reed this way. With a little practice one can put a bevel on a machine reed to duplicate a missing/broken "hand finished" reed if one of the right dimension is not available. Spreading out the area you remove material from also prevents weak spots.

I do a lot of work on tex mex boxes, and reed breakage is a common problem. One would think the tuning spots would be the common point of breakage, but it can be anywhere from the base near the rivet ,or 1/4 of the way down from the tip. Quality of reeds seems to not be an issue and the breaks as often as not are on a point of tuning.

 I was on a project with an art group I work with where we were building a 5 ft valved pulse jet. The valve was a piece of blued spring steel about 5 inches across, that looked like a steel daisy. Each petal covered a 3/4 inch hole that admitted a fuel air mix between "pulses". The engine worked fine for about 15 min before performance fell off and it started to flame back into the mixing chamber.
 Upon disassembly we discovered that the valve had shattered and frayed, no matter where petal was on the daisy the cracks ran in one direction as if it had been made of thin wood veneer. It was pretty clear at that point what was meant by metal sometimes having a grain. Wish I had a pic of it, but here is a link showing someone else's similar problem...https://www.google.com/search?q=pulse+jet+valve+design&client=firefox-a&hs=N26&rls=org.mozilla:en-US:official&source=lnms&tbm=isch&sa=X&ei=Fn0fUq-tFuK9sQS714CQBw&ved=0CAkQ_AUoAQ&biw=1280&bih=583#facrc=_&imgdii=_&imgrc=KB9aqnhkW49QXM%3A%3Bof3wpUrmL1814M%3Bhttp%253A%252F%252Faardvark.co.nz%252Fpjet%252Fimages%252Frvd3.jpg%3Bhttp%253A%252F%252Faardvark.co.nz%252Fpjet%252Fvalvelife.shtml%3B283%3B300
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

ChrisLDD

  • Good talker
  • **
  • Offline Offline
  • Posts: 64
  • ... but which way is up?
Re: How to efficiently ruin an accordion
« Reply #62 on: February 28, 2014, 11:12:31 PM »

I just came across this video showing a guy using a rotary tool to tune reeds.
I like the setup, and he appears quite proficient, but I would have liked to see how he lowered the pitch of an internal reed.

https://www.youtube.com/watch?v=lHi9W0YxFTI
Logged
Trying to learn enough magic to make my own melodeon.

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: How to efficiently ruin an accordion
« Reply #63 on: February 28, 2014, 11:35:42 PM »

Quote
It was pretty clear at that point what was meant by metal sometimes having a grain. Wish I had a pic of it, but here is a link showing someone else's similar problem..

I started an interesting thread about grain direction in steel accordion reeds a few years ago. It can be found here. It concerned me that grain in accordion reeds always runs perpendicular to the length of the reed, and this is (in my experience) always where a reed breaks. Seems to make more sense, from a usage but not necessarily production perspective, to make the grain run perpendicular to the reed's 'axis of flex' (a term I just invented.. :o).

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: How to efficiently ruin an accordion
« Reply #64 on: March 01, 2014, 01:39:38 AM »

I just came across this video showing a guy using a rotary tool to tune reeds.
I like the setup, and he appears quite proficient, but I would have liked to see how he lowered the pitch of an internal reed.

https://www.youtube.com/watch?v=lHi9W0YxFTI

love what looks like sparks at 6.40 into vid...dremel dream fettlin'   !!!
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: How to efficiently ruin an accordion
« Reply #65 on: March 01, 2014, 05:31:41 AM »

I just came across this video showing a guy using a rotary tool to tune reeds.
I like the setup, and he appears quite proficient, but I would have liked to see how he lowered the pitch of an internal reed.

https://www.youtube.com/watch?v=lHi9W0YxFTI

If you look back on Reply #57 (page 3 of this thread) there is a photo of bits. The leftmost is a spherical tipped diamond bit that is smaller in diameter than the shaft of the bit. This works well for lowering the pitch of an inside reed. I sort of use the same motion as a scratcher only less pressure is required. It makes a small grind line in the middle of the reed. The smaller head prevents accidentally grinding the sides of the reed slot. I find it controllable and quick.
Logged
too many boxes...please buy one, or two, or

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: How to efficiently ruin an accordion
« Reply #66 on: March 01, 2014, 04:12:10 PM »

I can't detect anything that would make him "appear proficient" and I'm afraid the title of this thread applies also for his way of "tuning".
Again, no problem as long as he damages his own boxes, but if he does this for a living it's a different story...
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: How to efficiently ruin an accordion
« Reply #67 on: March 01, 2014, 04:54:31 PM »

Quote
It was pretty clear at that point what was meant by metal sometimes having a grain. Wish I had a pic of it, but here is a link showing someone else's similar problem..

I started an interesting thread about grain direction in steel accordion reeds a few years ago. It can be found here. It concerned me that grain in accordion reeds always runs perpendicular to the length of the reed, and this is (in my experience) always where a reed breaks. Seems to make more sense, from a usage but not necessarily production perspective, to make the grain run perpendicular to the reed's 'axis of flex' (a term I just invented.. :o).

Steel doesn't really have a "grain" like wood -- it might seem to if you look at it under the microscope, but in spite of this the material is pretty much anisotropic (same properties in all directions), unlike wood there is no significant weakness at the grain boundaries.

Are you sure that what you think is "grain" isn't just machining/filing marks running across the width of the reed? These do act as stress concentrators unless very shallow which can lead to the reed breaking, which is why you should never leave grooves across a reed when scraping or filing it.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

ChrisLDD

  • Good talker
  • **
  • Offline Offline
  • Posts: 64
  • ... but which way is up?
Re: How to efficiently ruin an accordion
« Reply #68 on: March 02, 2014, 04:51:00 PM »

I can't detect anything that would make him "appear proficient" and I'm afraid the title of this thread applies also for his way of "tuning".
Again, no problem as long as he damages his own boxes, but if he does this for a living it's a different story...

I'm just an enthusiastic amateur, but based upon the look of the tuning table, I would guess that this guy is probably a professional tuner!

If you look back on Reply #57 (page 3 of this thread) there is a photo of bits. The leftmost is a spherical tipped diamond bit that is smaller in diameter than the shaft of the bit. This works well for lowering the pitch of an inside reed. I sort of use the same motion as a scratcher only less pressure is required. It makes a small grind line in the middle of the reed. The smaller head prevents accidentally grinding the sides of the reed slot. I find it controllable and quick.

Actually, based upon your recommendation, I bought a Foredom SR pendant drill with a rotary hand-piece and a selection of rubberised abrasive tips - I'm really pleased with the results. For work through the reed-plates I use a GRS850 with a small diamond burr.
Logged
Trying to learn enough magic to make my own melodeon.

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: How to efficiently ruin an accordion
« Reply #69 on: March 03, 2014, 04:32:59 PM »

Chris-
For raising the pitch of inside reeds I use a 200k rpm pneumatic dental handpiece. That works out to 3300 SFM (@ 1.6mm dia.)-reasonable for diamond coated bits. These are nice because the bit is 90 degrees from the handle. I am having special bits made (1.6mm shank) that only cut on the tip, not the sides so there is no danger of damaging the inside of the reed slot. If you would like to try one in your GRS 850, PM me and I will send one to you. Did you get the variable speed foot pedal with it? I'd like to know how well that works. I have an on/off pneumatic foot switch at the moment.

Scott
« Last Edit: March 03, 2014, 04:43:34 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

ChrisLDD

  • Good talker
  • **
  • Offline Offline
  • Posts: 64
  • ... but which way is up?
Re: How to efficiently ruin an accordion
« Reply #70 on: March 03, 2014, 11:10:09 PM »

Scott:
I did get the variable speed foot pedal, but the control is nowhere near as fine as on the pendant drill. I tend to find that I either use it full on, or for finer control, press and release the pedal and use it during the 2 second spin down time.

I would love to try my GRS 850 with one of the special bits you are having made - I will PM you.

Chris.
Logged
Trying to learn enough magic to make my own melodeon.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: How to efficiently ruin an accordion
« Reply #71 on: March 03, 2014, 11:28:17 PM »

These last 3 posts fit just perfectly into this thread.
Logged
Pages: 1 2 3 [4]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal