Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Any tips on removing still-soft wax?  (Read 3992 times)

0 Members and 1 Guest are viewing this topic.

WestOz

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 197
Any tips on removing still-soft wax?
« on: December 22, 2014, 07:59:03 AM »

I have recently acquired a 2-row Scandalli, which a previous owner has attempted to reaffix detached reeds - there is wax (sticky) everywhere. Any good ideas as to how to remove, other than physically scraping from the reeds, etc. with a scalpel. Other boxes I have rewaxed have had old, hard wax, which is relatively easy to deal with.
Logged
Castagnari Dony, DB Binci, Hohner Pressedwood,  Liliput, Preciosa,Octoput,etc.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Any tips on removing still-soft wax?
« Reply #1 on: December 22, 2014, 08:16:49 AM »

I physically scrape from the reeds, etc. with a scalpel.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Any tips on removing still-soft wax?
« Reply #2 on: December 22, 2014, 10:11:55 AM »

I use the blunt end of a phosphor-bronze Hohner reed lifter which I keep for this purpose. It's not as hard or sharp as a steel scalpel and there is less risk of damage to the reed plate or fingers. But a small blunt penknife blade would work as well.

Also you will probably need to remove some of the wax from the wood of the reed block and a blunt blade is less likely to dig in to the wood. If the old wax is still relatively fresh, you probably don't need to be obsessive about removing every last scrap of it - just ensure you have it clean enough to enable the reed plate to sit properly in place before applying new wax. The heat of the new molten wax will re-melt any last trace of the older wax.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Any tips on removing still-soft wax?
« Reply #3 on: December 22, 2014, 10:16:17 AM »

I use an old blunt kitchen knife with a broken blade and the end ground at 90 degrees.  I don't like using a sharp knife because if (a) the risk of cutting myself, and (b) the risk of accidentally removing wood.   

After scraping I use a soft wire brush to rub all the waxed areas to remove the last traces of wax.  The brush works with old and new wax.

If it really is sticky it might not be wax.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

WestOz

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 197
Re: Any tips on removing still-soft wax?
« Reply #4 on: December 22, 2014, 02:32:09 PM »

Thanks for the suggestions - it seems there is no easy way, such as washing the reeds in hot kerosene?
Logged
Castagnari Dony, DB Binci, Hohner Pressedwood,  Liliput, Preciosa,Octoput,etc.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Any tips on removing still-soft wax?
« Reply #5 on: December 22, 2014, 02:52:20 PM »

I have been known to leave old reedplates in a bath of methylated spirit (I think that's denatured alcohol in the US) overnight to soften old wax, but in the end it's still down to careful scraping and brushing.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Foma

  • Member
  • *
  • Offline Offline
  • Posts: 21
    • Гармонь
Re: Any tips on removing still-soft wax?
« Reply #6 on: December 22, 2014, 03:30:34 PM »

Heat in the oven (about 100 degrees) - the wax will flow out?
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Any tips on removing still-soft wax?
« Reply #7 on: December 22, 2014, 04:01:58 PM »

Thanks for the suggestions - it seems there is no easy way, such as washing the reeds in hot kerosene?
You can use a solvent, but I wouldn't recommend anything hot just in case any differential expansion of the reed late/reed tongue/rivet disturbs the security of the riveted joint. It might be unlikely but I wouldn't be prepared to take the risk.

I've used acetone-based nail polish remover at room temperature to get rid of the last vestiges of wax, followed by a rinse in methylated spirit.

All this assumes, of course, that you will be replacing the valves as well. If you use any kind of solvent, don't expect the existing valves/adhesive to remain unscathed.  :o
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Any tips on removing still-soft wax?
« Reply #8 on: December 22, 2014, 04:06:22 PM »

I've cleaned reeds in an ultrasonic cleaning bath with good results.  You have to choose the correct sort of cleaning solution that won't harm aluminium, the cleaning solutions are water based and work best in hot water around 80 to 90C. I've seen no detrimental effects.  Ultrasonic is THE best way of getting muck, dirt, corrosion and wax debris out of tiny books and crannies.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

CherzeduKbec

  • Guest
Re: Any tips on removing still-soft wax?
« Reply #9 on: December 22, 2014, 09:58:38 PM »

Here's my method.
Remove reeds from the block by cutting wax with an unsharpened knife.
Gently remove wax from the block with the same knife with care to not scratch the wood.
Gently remove valves from the reed plates.
Put reeds in a glass jar or metal tin can and add enough automobile gasoline to immerse reeds. Soak for at least one hour.
Then carefully rub the reed plates with a soft toothbrush and rinse in another container of clean gasoline. Allow to dry in the open air on an old piece of cloth.
This method does not alter the finish of the plates neither the reeds. This removes old wax and the latest wax. rust and traces of almost any kind of adhesives used to bond the valves. There is no residual odors.
The instrument shall be surely to retuned after reinstalling the reeds.
I used this method several times always with excellent results.


« Last Edit: December 22, 2014, 10:41:08 PM by CherzeduKbec »
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Any tips on removing still-soft wax?
« Reply #10 on: December 28, 2014, 11:03:23 PM »

If the "wax"is very sticky I would think that your new wax should stick to it very well ,so scraping it off with the edge of a dull chisel and leaving a little of it should not cause a problem.
 I agree with the ultrasonic ,I used "simple green" (citrus based cleaner) and water on a bandeoneon that had a tarry layer of cigarette smoke on all the reeds.
 Soaking in mineral spirits or diesel works well for removing wax.I like denatured alcohol for quick cleaning at the bench.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

ACE

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 535
Re: Any tips on removing still-soft wax?
« Reply #11 on: December 30, 2014, 04:33:52 PM »

Seems like a good use for that cheap aftershave you got for xmas. Leave the top off for a couple of hours to get rid off the smell. Or if you are a bit light on the loafers, leave it smelling sweet. I use the stuff for all sorts of cleaning.
Logged
Paddy Clancy, paddlewheel gob iron cheepo g/d anglo
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal