Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Functional stops conversion  (Read 1371 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Functional stops conversion
« on: December 31, 2017, 06:28:39 PM »

Has anyone ever converted a 4-stop one-row with dummy stops to functional ones? Is this a reasonable undertaking for a seasoned fettler or builder? (Not me...)
Logged
C#/D player

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Functional stops conversion
« Reply #1 on: December 31, 2017, 06:59:11 PM »

This would involve removal of the existing blocks, design and installation of slides and new inside plate on which the blocks can be reinstalled (if they survived removal).  It's feasible in theory but there may be challenges, depending on the specifics of the 'patient'.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Functional stops conversion
« Reply #2 on: December 31, 2017, 07:11:21 PM »

It will depend critically on the size and spacing of the vent holes under the reeds.  There must be enough space between the holes so that the register slides can close the holes. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Functional stops conversion
« Reply #3 on: December 31, 2017, 07:50:29 PM »

Good point Theo.  There seems to be many approaches to this problem, even on boxes made with working stops.  To mention a few I've seen:

- size of the hole in the slide matches the hole in the faceplate but is more than distance between adjacent holes.  As a result, there are small gaps visible (and air loss) in the 'closed' position.  (Messervier)
- hole in the slide is centered on hole in faceplate but has slightly smaller diameter to avoid the gaps.  (Acadian)
- faceplate opening is square or rectangular, slightly smaller round holes in slide.  (Breton)

The Acadian and Breton end up with flared opening, which may be argued to improve projection.  ;)
« Last Edit: December 31, 2017, 07:59:56 PM by tirpous »
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Functional stops conversion
« Reply #4 on: December 31, 2017, 08:12:20 PM »

None of this is possible if the reed-block assembly is glued in, which is very often the case with Cajun, Quebecois and Welsh accordions.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Functional stops conversion
« Reply #5 on: December 31, 2017, 08:20:19 PM »

The assumption is that reedblocks are glued-in.
Logged
C#/D player

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Functional stops conversion
« Reply #6 on: December 31, 2017, 09:28:39 PM »

Depending on the type of glue used then it may be possible to loosen the blocks with steam (after removing the reed-plates of course).
If Titebond or Resin W has been used, forget it, you'll rip the fondo board thing.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Functional stops conversion
« Reply #7 on: January 02, 2018, 07:36:20 AM »

If the reedblocks are glued in with hide glue. I have had success removing them using a heated oilpainter's pallet knife. Once a small gap is created, success is possible. It takes patience and many many reheats of the knife. If the reedblocks are held in with alphatic resin( titebond et al) or PVA glue it would be possible to saw the reedblock loose from the trebleboard, after removing the treble frame, using a very small japanese pull saw with no set to the teeth. I have done this. I usually use the saw described for cutting fret slots in new fingerboards for stringed instruments.  Careful clean up after sawing is required to prevent reed clogging from the dust created. I would suggest using the thinnest 3 ply material you can find for the slides.  Plywood made for model airplane construction can be obtained down to a few mms in thickness.
« Last Edit: January 02, 2018, 07:50:31 AM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Functional stops conversion
« Reply #8 on: January 02, 2018, 07:41:40 AM »

Matt, I had originially planned the conversion you are inquiring about on the Robert Maheux box I purchased from you, but decided not too because I really like the was this instrument sounds. I was concerned about the potential change in timbre which might occur from the retrofitting of stops.
Logged
I'm squeezin' and they're wheezin': old junker boxes
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal