Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Solvent for "Araldite" type Glues.  (Read 1777 times)

0 Members and 1 Guest are viewing this topic.

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Solvent for "Araldite" type Glues.
« on: August 18, 2016, 12:07:12 PM »

I have just been given a very nice bellows, slightly smaller than a Hohner  pokerwork/Erica bellows, but potentially very useful for a compact lightweight single voice box somewhat like a lily or similar, .....only problem is the end frames which are amateurishly made and ill fitting have been attached using what looks like Araldite or a similar two pack epoxy glue, and I'm wondering what's the best way to remove them without damaging the bellows itself,.... or indeed if its even possible, anyone have any helpful suggestions,  for example, is there a solvent for such glues  ??????
« Last Edit: August 18, 2016, 12:37:32 PM by Henry Piper »
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Solvent for "Araldite" type Glues.
« Reply #1 on: August 18, 2016, 12:29:23 PM »

I'm fairly sure there isn't a solvent for Araldite.......
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Solvent for "Araldite" type Glues.
« Reply #2 on: August 18, 2016, 12:48:28 PM »

My inclination would be to use a very fine sharp saw to cut through the glued join where the bellows meets the wooden frame.
Use an X-ACTO saw or similar (available from craft/model making suppliers).

http://www.ebay.co.uk/itm/X-Acto-Precision-Razor-Saw-Set-X75300-/400931826513?hash=item5d59662b51

Then glue the bellows to the new frame using PVA wood-working glue and clamp solidly (place between boards under a heavy weight) until set.

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Solvent for "Araldite" type Glues.
« Reply #3 on: August 18, 2016, 01:20:33 PM »

I would leave the old frames in place until you have a new set to put on.  The old ones will protect the ends of the bellows.
Rather than a saw, I would use a knife.  Stanley type with a new blade. With either tool it will be very difficult to cut through the glue line as the tool will tend to wander into the softer material of the bellows.
If the frames are definitely to be discarded you could use a circular saw to cut through the frames and leave a veneer of glue on the bellows. Run the frame against the fence and take a few short trial cuts from each corner to check that the frame thickness is consistent.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Solvent for "Araldite" type Glues.
« Reply #4 on: August 18, 2016, 03:00:36 PM »

After any major surgery, Any little blobs of araldite can be filed off quite nicely as its that hard!
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Solvent for "Araldite" type Glues.
« Reply #5 on: August 20, 2016, 11:03:46 AM »

Working on my boat, I've had a dribble of epoxy resin harden unnoticed on the GRP.  A couple of years of UV exposure and it's gone.  On the other hand in my youth (now 63) I used Araldite to fill a bad chip in a recorder mouthpiece.  It's still as good as new, but the filler made it softer than pure epoxy and it could be finished with a scraper.  You may well find that once most of the bulk is removed a skarsten scraper or a cabinet scraper will smooth the remainder to a usable surface.  If you have neither tool, often a steel rule will do the job.

Rob.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal