Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Broken pallet arm  (Read 2821 times)

0 Members and 1 Guest are viewing this topic.

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Broken pallet arm
« Reply #20 on: March 11, 2019, 11:17:11 AM »

In many similar applications (i.e. tracker action on organs) threading is done by rolling (as wheel spokes) rather than cutting, probably a quicker process per thread made but initial cost of the rolling dies, head to hold them and hand turning unit (or head can be operated in a lathe) is comparatively high.

Because this is a deforming rather than cutting action, threads are inherently stronger with less opportunity for fatigue cracks to develop - possibly overkill for melodeons but if you saw a cheap spoke rolling tool for sale it might be worth investing in, especially for ali rods.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Broken pallet arm
« Reply #21 on: March 15, 2019, 12:41:34 PM »

Update: I contacted the original maker (who built the box nearly twenty years ago), and he made and sent me new pallet arms free of charge. Now to get the broken bit out of the keyboard..
Logged
C#/D player

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Broken pallet arm
« Reply #22 on: March 15, 2019, 02:04:30 PM »

Update: I contacted the original maker (who built the box nearly twenty years ago), and he made and sent me new pallet arms free of charge. Now to get the broken bit out of the keyboard..

Good news and good luck...
Logged
On the edge of Cheshire's Golden Triangle, apparently...

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Broken pallet arm
« Reply #23 on: March 15, 2019, 02:51:17 PM »

Update: I contacted the original maker (who built the box nearly twenty years ago), and he made and sent me new pallet arms free of charge. Now to get the broken bit out of the keyboard..
That’s good! I would have ask for a new wood lever just in case, if he had one. ( its the Winston in me ;))
Getting that out sounds tricky as its flush and small in size so hard to get anything on it.
Being flush could you slice the remaining bit slightly enough to get a screwdriver on it? It might break being aluminum and was there any glue applied?
I think Theo is right that it will be easier to make one, the lever that I made is for a 5/16” groove so its a tad under 1/64”, the notch I made is 1/8” deep and 1/14” long  if you think that might work I could send you a piece that size,actually there’s two on this bit of wood.
I also have the one shown that I could cut to the groove width (oversized slightly) so you could sand to fit. If that would help you out let me know.
I did mine as Theo suggested and sanded to fit on a flat surface, I used my table saw and 100 grit , its important to keep even pressure when you do this for its easy to roll it. I find spinning it from time to time helps, the leading edge wears quicker because of the force applied even if it’s minimal.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Broken pallet arm
« Reply #24 on: March 18, 2019, 07:29:45 AM »

I would remove the stub from the lever and reuse the existing key. I have an antique hand crank drill press which I find most useful for sensitive instrument repair work. I have used this tool to drill out broken screws from woodwind keys, of a much smaller diameter the the wire on your melodeon Matt. It helps to file the exposed end of the wire flat and the mark the center of the stub with a very small "automatic" i.e. A spring loaded punch which creates an impression without needing to use a hammer to strike the punch. I would start with a very small drill bit and drill out the center of the stub. Gradually increase the drill size until the is just a thin layer of metal left. It should then be possible to deform the remains into the center hole and pick out the bits. If you have  reverse twist drill bits, sometime a threaded piece will unscrew out as it is being drilled, simplifying the removal. I prefer to make the pallet rods out of silicon bronze rather than the commonly used aluminium or copper wire used by most low production builders. The silicon bronze wire is avaiable in a wide range of diameters and can be easily bent and forged into complex shapes if heated to red just before bending. For the replacement rod, I would knurl the end to be inserted, or press in longitudinal grooves rather than threading the end.
Logged
I'm squeezin' and they're wheezin': old junker boxes

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Broken pallet arm
« Reply #25 on: April 02, 2019, 05:04:11 AM »

Thanks everyone for your replies and suggestions.  I tried using an extractor bit to remove the rod, but with no luck. Further attempts to drill it out didn't go well either, so in the end I simply made a new wooden key as suggested by a few people. The maker of the accordion sent me new pallet arms, so I used one of those and salvaged the spring, button, etc from the old key.  In the end, the repair was successful, so I'm happy to have this box working once again!
Logged
C#/D player
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal