Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: A question regarding the alteration of bellows dimensions  (Read 769 times)

0 Members and 1 Guest are viewing this topic.

Ribs

  • Member
  • *
  • Offline Offline
  • Posts: 29
A question regarding the alteration of bellows dimensions
« on: February 05, 2020, 10:11:56 PM »

Hello all!

So, over the past two weeks, I've been experimenting with different things using various accordion parts that I've collected over time. I've finally settled on a real project, which is to make a tiny variant of an English concertina. I'll spare you the thousands of little details and get right to my question: Does anyone have any ideas on how I could alter the dimensions of an old set of PA bellows that I have laying around? To be clear, this thing is still going to be rectangular; I'm not trying to turn the bellows into traditional concertina bellows. As an example of what I'm asking, could I, say, cut three inches out of the middle of the bellows and then rejoin the two ends in some way?

I apologize if this is a stupid question. I've only got one old PA bellows that's even remotely usable at the moment, so I thought I'd consult people who know what they're doing before I just wing it and hope for the best.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: A question regarding the alteration of bellows dimensions
« Reply #1 on: February 05, 2020, 10:20:28 PM »

In my minds eye, this was going to be so easy, however, in practise it proved quite beyond me. I wasted two sets of good bellows!
You could save your bellows for something else and instead, get some card and then find the video where a bloke folds card into bellows without corners and just needs to glue one edge together.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Ribs

  • Member
  • *
  • Offline Offline
  • Posts: 29
Re: A question regarding the alteration of bellows dimensions
« Reply #2 on: February 05, 2020, 10:50:25 PM »

In my minds eye, this was going to be so easy, however, in practise it proved quite beyond me. I wasted two sets of good bellows!
You could save your bellows for something else and instead, get some card and then find the video where a bloke folds card into bellows without corners and just needs to glue one edge together.

I actually just watched that video hoping for an alternative, and I may end up giving it a shot if reusing these PA bellows doesn't pan out.

If you don't mind me asking, how did you go about attempting to do it? So I know what to avoid.
Logged

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: A question regarding the alteration of bellows dimensions
« Reply #3 on: February 06, 2020, 05:26:50 AM »

I have done this to cut bellows down in one dimension. I cut an 80 bass paolo soprani pa down by about 3 inches. Turned out ok, but i did not realise at the time i the original bellows were not stiff enough for diatonic play. I have since cut the number of folds down to compensate.
Bellows have cloth, not papers, some of the cloth did not detach easily near the joints or glue back well. I should have left in place.
Cut down using a fine saw at one end, cut all the folds in one go while clamped together, take the metal corners off, then remove the section of redundant card from the gussets. Glue back together, then replace the metal corners.
Retaping was then done.
It would have been easier to buy new, but i wanted to cut down a full size 3 voice paolo pa to button accordion with original parts.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal