Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed pitch is unstable - any ideas please?  (Read 1774 times)

0 Members and 1 Guest are viewing this topic.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Reed pitch is unstable - any ideas please?
« on: October 10, 2009, 08:08:59 AM »

As some of you will know, I've recently been fine-tuning the 1-row 4-stop melodeon which I built at Stowmarket a year ago. Thanks to Theo's and Rees's expert tuition at both Stowmarket and Mendlesham last March, I've assembled or made all the tools required and slowly, gently, made a start and gaining confidence as I progressed, went on to complete the tuning of the entire instrument. I have to say it is now sounding pretty good (and I am quite critical when it comes to tuning), and I just can't stop playing it!  There is one minor problem which is annoying me and if anyone has advice I'd be grateful.

The melodeon is a 4-voice in D, tuned M+, M, L, H, with the M+ reeds being no more than 2 - 4 cents sharp across the range, so there is just the hint of tremolo. The M L H voices are exact unison octaves. The reeds are Binci hand-made type, on aluminium plates screwed on to the reed chambers.

The problematical reed is the M+ push D in the middle of the range (2nd line down on the treble stave). At low to medium bellows pressure, the pitch is OK, but on medium to strong pressure the reed plays sharp by as much as 15 to 25 cents. This means that when playing with all four voices on a good punchy tune with staccato attack, there is a noticeable rough tremolo which lasts a fraction of a second before the pressure moderates and the pitch settles down.

The sound quality of the reed is slightly different from the others too; difficult to describe but it has a rather twangy, hollow metallic sound, compared with the purer sound of its fellows. There is no dust or similar in the reed plate/reed tongue edge, and as far as I can tell the leather valve is OK.

I suspect the problem is due to the 'set' (gap) of the reed tongue above the reed plate. However, the gap looks similar to its neighbours and the reed speaks easily and is not 'breathy'. I've tried adjusting the gap slightly up and down, but it doesn't seem to make much difference to the variability in pitch.

I would be grateful for any ideas and advice.

Edited to add: I've just noticed that it is exactly a year since my melodeon started its life as a pile of cherry wood strips in a room in the Abbott's Hall in Stowmarket. Also this post has been my 500th and I appear to have been elevated to the status of 'hero member'. So if someone can help me solve my reed problem, that will be cause enough for a triple celebration, I think.
« Last Edit: October 10, 2009, 08:21:45 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed pitch is unstable - any ideas please?
« Reply #1 on: October 10, 2009, 09:04:59 AM »

First thing to check is that the valve under the reed can move freely.  If it is brushing the sides of the chamber it may be slow to open which will cause the symptoms you describe.  Since you have screwed reedplates its easy to reposition the plate slightly.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

HallelujahAl

  • Guest
Re: Reed pitch is unstable - any ideas please?
« Reply #2 on: October 10, 2009, 09:06:29 AM »

Unlikely to be a duff reed tongue Steve. If it were going flat when under pressure I'd say metal fatigue. More than likely a valve issue.
AL
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed pitch is unstable - any ideas please? Sorted - thanks!
« Reply #3 on: October 10, 2009, 02:55:53 PM »

Thanks Theo and Al,

The problem was indeed the valve on the underside of the reed plate fouling the end of the reed chamber. I changed the valve, enlarged the reed chamber just a frazzle (Steve-speak for about 0.5 mm) at the end, repositioned the reed plate, and it's just fine now.  (:)
Many thanks for your help!

Off to play some Quebecois reels now.....
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

jackd_123

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Reed pitch is unstable - any ideas please?
« Reply #4 on: October 17, 2009, 04:04:24 PM »

some times tightening the reed to the plate helps, by giving the rivet a healthy whack - Jack
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal