Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed Cleaning  (Read 637 times)

0 Members and 1 Guest are viewing this topic.

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Reed Cleaning
« on: November 13, 2022, 06:45:15 AM »

Okay so I have made a start in learning how to repair and tune Melodeons.
I am doing this out of pure curiosity because I am intrigued by them as I am with vintage sewing machines.
I am not out to make a quick buck but to hold back the dementia, get frustrated and bury myself in another world.
So far, I have made a tuning table out of a shot melodeon, bought some knackered ones to play with ( reed tuning ) bought and downloaded Dirks accordion tuner and I have Aireyware app on my phone.
I played with Dirks tuner last night and it is just mind blowing how he ever managed to do it.
I can see the three reeds beating at once on the screen with a cents count, beat count and graphs toboot.
It was worth the money just to play around with it.
Anyway...I have ordered a largish ultra sonic cleaner to clean the reeds.
I am guessing that this is really the only way to zap them good and proper and including the ones underneath!!!
I have watched Lester do it.
Lester is my hero so I copy him coz he knows that he knows.
Therefore follow him.
The question is....
Do I actually need a ultra sonic cleaner to mix with the water and if so....what do I look for?
Cheers.
Peter ( I am in Australia )
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Reed Cleaning
« Reply #1 on: November 13, 2022, 09:04:38 AM »

The answer I was given when I asked this question was Acetone. I used it in a lidded jar where I submerged a few reed plates at a time, let them soak, then gently agitated them before lifting them out with tweezers. The end result is a lovely clean reed. Usual precautions should be observed when using acetone, well ventilated and no naked lights.  :)

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed Cleaning
« Reply #2 on: November 13, 2022, 10:02:24 AM »

I had an ultrasonic cleaner but did not find it useful. I found I had to use scraping and brushing to remove most of the wax, valve glue and heavy rust before the US could do anything useful.  Once they come out yiu have to dry them immediately, or a light rusting would appear on the reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Reed Cleaning
« Reply #3 on: November 13, 2022, 02:11:35 PM »

I actually have pretty good experience with ultrasonic cleaner, but I don't doubt Theo's experience. I think the effectiveness may very depending on the wax/glue that was used on your reeds.

I have a small jewelry ultrasonic cleaner I found at a thrift store for $5, just big enough for eyeglasses but nothing nice or fancy.
I peeled off the old leather valves and scrapped off any large chunk of wax, but didn't otherwise work it too much.
I dropped one set (~20 treble reeds) of the reeds in straight acetone in a pint size glass jar (with lids) sitting in the ultrasonic cleaner, and just let it run for a few minutes. After running through all the reeds the acetone is rather murky, so I did a second cleaning on all the reeds again on fresh acetone.

My reeds were then soaked in Evapo-Rust for a few hours (and in ultrasonic cleaner) to remove the heavy rusts. They came out sparkling clean (although I am not sure this is the best way to remove rust on reeds as it also removes the bluing).

Picture for reference. It's Evapo-Rust in the jar.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reed Cleaning
« Reply #4 on: November 13, 2022, 05:04:36 PM »

I get some really bad ones sometimes. After scraping I would put them in the cleaner with a strong hot solution of water and "simple green" cleaner degreaser. after cleaning I would dump them in a colander and dump boiling water over them to rinse.
 I would dump them on a towel immediately and pat them dry. The reeds were hot so they would dry almost at once without rusting but a hair dryer won't hurt.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Reed Cleaning
« Reply #5 on: November 13, 2022, 07:16:53 PM »

Mmhhhh....a mixed bunch of replies but that is to be expected. When I watched videos of US cleaners in use to clean reeds I was quite surprised that water was used in the first place. The reed itself is riveted on with a steel pin and water surely MUST get into that and under the reed where it is clamped to the reed shoe.
Unless the reed clamping is totally watertight?
I agree with you by using acetone as afterwards there can not be any signs of rust.
I get the point about wax and glue removal before the US cleaner can do anything.
Thanks for your replies.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reed Cleaning
« Reply #6 on: November 14, 2022, 02:03:27 AM »

 Water is not really a problem , I have a black powder revolver and this is pretty much how you clean it, though typically one would oil it after but that is not recommended for reeds.
 One could boil the reeds and skim off the wax that would come to the surface but it starts to get complicated.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal