Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Dremel vs. File  (Read 5542 times)

0 Members and 1 Guest are viewing this topic.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Dremel vs. File
« Reply #20 on: September 04, 2023, 09:18:25 AM »

Tuning in situ offers two big advantages: First, the reeds are tuned in their natural acoustic environment. Second and equally important: it allows you to use the keyboard and, if present, the register switches. Trying to fine-tune single blocks on a tuning table is a waste of time.
« Last Edit: September 04, 2023, 09:22:16 AM by diatonix »
Logged

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Dremel vs. File
« Reply #21 on: September 08, 2023, 06:56:14 AM »

Tuning in situ offers two big advantages: First, the reeds are tuned in their natural acoustic environment. Second and equally important: it allows you to use the keyboard and, if present, the register switches. Trying to fine-tune single blocks on a tuning table is a waste of time.
"in situ" does this means you have one half of the instrument on a tuning bellows or do you open and close the box countless? I fully understand that the enclosure affect the pitch drastically but i think with patience and experience one can get good results tuning on the table. My first attempt of building a tuning table came out not that bad, because it allows the bellows to sink down buy gravity for quite a while without pulling with extra force wich results in a consistent "sucking power  :-[".
My second table is more compact with the bellows installed on the surface but i found out that the variable force that is used to move the bellows can variate the pitch a lot, and it is better if the result is replicable.
Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Dremel vs. File
« Reply #22 on: September 08, 2023, 09:56:22 AM »

Well, it is the opinion of most experienced tuners I have met or read, that proper fine tuning should be done inside the instrument. Yes, this means you have to open eland close the box again and again, but that's the job.
It is a tedious, meticulous job, and you can't really take shortcuts.

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Dremel vs. File
« Reply #23 on: September 08, 2023, 10:17:36 AM »

"Opening and closing the box" is a bit of an overstatement, surely?

If the reeds are on the blocks, in the end which is being tuned, then all it needs is to be plopped on top of the other end with the bellows attached, which are hanging in a holder of some description. There's no need to have the pins in!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Dremel vs. File
« Reply #24 on: September 08, 2023, 10:25:57 AM »

"Opening and closing the box" is a bit of an overstatement, surely?

If the reeds are on the blocks, in the end which is being tuned, then all it needs is to be plopped on top of the other end with the bellows attached, which are hanging in a holder of some description. There's no need to have the pins in!
Like THIS and THIS

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Dremel vs. File
« Reply #25 on: September 08, 2023, 02:03:49 PM »

Exactly, Mr Bailey! Just like these as well.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Dremel vs. File
« Reply #26 on: September 08, 2023, 02:49:34 PM »

thanks for the pictures, very helpfull indeed, but this way you have to make a tool for every instrument size.
I was thinking about building something like this:
« Last Edit: September 08, 2023, 11:46:57 PM by Stefan »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Dremel vs. File
« Reply #27 on: September 08, 2023, 03:52:05 PM »

thanks for the pictures, very helpfull indeed, but this way you have to make a tool for every instrument size.
I was thinking about building something like this:
Not really you just use the bass end of the box you are tuning and fix it to your bench with the support board and some clamps

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Dremel vs. File
« Reply #28 on: September 08, 2023, 04:00:39 PM »

Not really! If you look closely at my pictures, you'll see the butterfly nuts towards the back. They allow an adjustment of however much you decide when making the rig up.
Mine does Liliputs (and smaller!) and up to the 3 voice Clubs, without any problems.
The picture you posted doesn't do the same job, as it doesn't use the actual instrument's own bellows. It's just a set of bellows of whatever size it is.
« Last Edit: September 08, 2023, 04:03:18 PM by Winston Smith »
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Dremel vs. File
« Reply #29 on: September 08, 2023, 11:51:13 PM »

i am so glad to joined this board, so much friendly fellows willing to share their wisdom and expertise.
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Dremel vs. File
« Reply #30 on: September 10, 2023, 05:29:28 PM »

Just wanted to say thanks for the input over using a frame to hold the lower part of the box while undertaking "in box" fine tuning. Supporting at the end of the bellows makes complete sense.

To date I have been fine tuning by using offsets for some reason. ::) i.e. actually playing the closed box, mapping the offsets and then opening and adjusting (which is a pain as the closure mechanism is fiddly)

So .... following your posts I have just built my own frame .... so happy days!   Without it I would still be opening and closing.

Just wanted to say thanks ....  ;D

John

Here are some pictures (made from 3mm ply and 70mmx10mm - an easy build) :



« Last Edit: September 10, 2023, 07:01:44 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Dremel vs. File
« Reply #31 on: September 10, 2023, 05:33:15 PM »

and others:
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Dremel vs. File
« Reply #32 on: September 10, 2023, 05:59:23 PM »

So…this is just my own opinion and people do approach these things differently..but…You really don't need the frame thing to hold the bass end. I just lift the end on and off the end while it's sitting on the bench. I'm pretty good at sounding the notes by rocking it front to back, or gripping a fold and the end. I do this for pretty much all instruments (nb: I do also use my tuning bench, but not for fine tuning). Or, even easier, just make a tuning bellows with a hole big enough to sit the end on, which is what e.g. Bugari factory tuners do. It probably takes less time to make that (as long as you have spare pa bellows) than the U shaped rig to sling the bass end. The one i have works with most Hohner melodeons.
« Last Edit: September 10, 2023, 06:07:27 PM by Rog »
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Dremel vs. File
« Reply #33 on: September 10, 2023, 06:14:41 PM »

In Thierry Benetoux's book, he recommends filing towards or away from the rivet, rather than across. Or at least directing the file more along the tongue than across it, thus preventing rotation on the rivet. Also you'll be surprised how little downward force you need to apply if you have a sharp file…and a longish file, so you can get a long stroke, if required. And use a v bright light, so you can see exactly what’s going on with the filing. If you bounce the light onto the tongue at an angle it helps to show the cut, esp when you are learning. It’s also worth just filing some metal..any metal… to learn how to use a file. Some of us on here were put through practical training (when we was young …a long time ago) where you spend 6 weeks filing metal (it’s called 'fitting'..the most boring thing you can imagine…filing a chunk of bright steel hour after hour). So it’s a skill to be learned and you don’t necessarily need to he filing reed tongues.

The test piece we had to do -- the dimensions tell you how long ago it was! -- was to produce a 2" square piece from 1/8" steel plate, with a 1" square hole in the middle at 45 degrees, and a square plug to fit into this. All edges had to be perfectly square so it would stand vertically on a surface plate, and the 1" square piece had to fit snugly into the hole all 8 possible ways with no visible gaps anywhere. Available tools: ruler, straight-edge, try-square, files.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Dremel vs. File
« Reply #34 on: September 10, 2023, 06:56:44 PM »

.and a hacksaw. I think we had hacksaws…do you still have your test pieces?

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Dremel vs. File
« Reply #35 on: September 10, 2023, 08:28:52 PM »

The test piece we had to do -- the dimensions tell you how long ago it was! -- was to produce a 2" square piece from 1/8" steel plate, with a 1" square hole in the middle at 45 degrees, and a square plug to fit into this. All edges had to be perfectly square so it would stand vertically on a surface plate, and the 1" square piece had to fit snugly into the hole all 8 possible ways with no visible gaps anywhere. Available tools: ruler, straight-edge, try-square, files.

Filing exercise, 1971.

Tools: Junior hacksaw, 2mm drill bit, 4mm drill bit, half round flat file, metal rule, set square, centre punch, scribe, vernier.
Material: 1/8" steel plate and a length of 25mm dia. round bar.
Task:
1. Three holes, 1" Equilateral Triangle, 1" x 1" square and 1" dia. circle, to be put into plate.
2. Use tools to manufacture an object out of the round bar that can pass through all three holes in the plate.
Tolerance on all dimensions 0.2mm.
Mixed Imperiel and Metric dimensions were pretty normal, at the time.

Took a lot of goes and months of effort to get it to standard.

...and no. I don't have it any more. I hated the bloody thing. I can file flat and square and cut to a straight line, though.

« Last Edit: September 10, 2023, 08:34:21 PM by Tone Dumb Greg »
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Dremel vs. File
« Reply #36 on: September 11, 2023, 11:08:35 PM »

.and a hacksaw. I think we had hacksaws…do you still have your test pieces?

I don't think so, this was in the late 70s, I haven't seen them for a *very* long time -- probably last time we moved house in the 90s...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Dremel vs. File
« Reply #37 on: September 11, 2023, 11:09:50 PM »

The test piece we had to do -- the dimensions tell you how long ago it was! -- was to produce a 2" square piece from 1/8" steel plate, with a 1" square hole in the middle at 45 degrees, and a square plug to fit into this. All edges had to be perfectly square so it would stand vertically on a surface plate, and the 1" square piece had to fit snugly into the hole all 8 possible ways with no visible gaps anywhere. Available tools: ruler, straight-edge, try-square, files.

Filing exercise, 1971.

Tools: Junior hacksaw, 2mm drill bit, 4mm drill bit, half round flat file, metal rule, set square, centre punch, scribe, vernier.
Material: 1/8" steel plate and a length of 25mm dia. round bar.
Task:
1. Three holes, 1" Equilateral Triangle, 1" x 1" square and 1" dia. circle, to be put into plate.
2. Use tools to manufacture an object out of the round bar that can pass through all three holes in the plate.
Tolerance on all dimensions 0.2mm.
Mixed Imperiel and Metric dimensions were pretty normal, at the time.

Took a lot of goes and months of effort to get it to standard.

...and no. I don't have it any more. I hated the bloody thing. I can file flat and square and cut to a straight line, though.

We didn't have months, I was only there for a month IIRC. Did teach me how to cut and file straight, though... ;-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Dremel vs. File
« Reply #38 on: September 12, 2023, 02:43:02 PM »

its quite difficult to modify the "inner" reeds (even more when the blocks are srewed inside the box), I know how to bend the inner reed up from inside the block (or from outside with the angle) and can scratch at the base of the reed to lower the pitch but how the heck should it be possible to file the tip of the reed when bending up (through the plate)??? I avoid this, but with a dremel this should be easier.
It's not that hard actually. You can have access to the inner reed without removing the reed block with a simple hook. You can make it with a piano string, and attach it to a small handle, or you can attach it to your file with a stripped insulated screw joint (see attached picture). You can also use make a small tool out of spring-steel (like the one on the picture). With that you can lift the outer reed tongue to have enough room to insert the small hook, and with a rotation of the hook you can bring out the inner reed tongue. It tooks a bit of practice, but when you get the hang of it you can have access to the inner reed in virtually no time.

If the reeds are on the blocks, in the end which is being tuned, then all it needs is to be plopped on top of the other end with the bellows attached, which are hanging in a holder of some description. There's no need to have the pins in!

I've been using a somewhat similar device, quite versatile. It's just a bench with metal corner strips that you insert in the bellows folds and that you screw with threaded rods. The lower surface is covered in leather to make the device as airtight as possible.
This way you can either tune with the bellows and either the treble or bass end, or if it's more convenient you can let the whole accordion on his feets and just hold it in place. See attached pictures, it'll be clearer.
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal