Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Scarlatti Improvement (?)  (Read 6478 times)

0 Members and 1 Guest are viewing this topic.

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Scarlatti Improvement (?)
« Reply #20 on: May 28, 2011, 06:58:07 PM »

I have seen another way of limiting treble button travel on a Pokerwork. This on our Foreman's box, probably from before his ownership. It seems to work fine for him.

A "simple metal bar" proved to be a probably cast or possibly machined piece of, perhaps, brass or bronze, with holes  to accept mounting screws at either end and a raised flat centre section to fit over the levers of the pallets. Felt on the underside, against which the pallet-arms stop. Works against the pallets going up rather than the buttons going down. Accessible by removing  only the grille.

Limit of travel similar to photographs on Theo's Facebook mentioned above.

My thoughts on it were that it offered easier installation, but I wondered about possible fatigue on the pallet arms as the felt compresses. Also wasn't sure about driving extra screws in the board the pallets seat against. Is that a sound-board? if so, what about structural and acoustic risks?

Wondered who was providing that part, and when.

 Any thoughts, please?



Hi Peter,

Sounds like a case of over engineering to me - ie, if it ain't  broken, fix it 'til it is  :o.

Probably best to stick with the easiest and probably the best and simplest method mentioned by Theo and others.
If you would like any info regarding measurements etc. I would be glad to help.

Martyn
www.melodeonrepairs.co.uk
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Peter_T

  • Good talker
  • **
  • Offline Offline
  • Posts: 88
Re: Scarlatti Improvement (?)
« Reply #21 on: May 28, 2011, 09:38:04 PM »

I have seen  ...

A "simple metal bar" proved to be a probably cast or possibly machined piece of, perhaps, brass or bronze, with holes  to accept mounting screws at either end and a raised flat centre section to fit over the levers of the pallets. Felt on the underside, against which the pallet-arms stop. Works against the pallets going up rather than the buttons going down. Accessible by removing  only the grille. ----


....

Sounds like a case of over engineering to me - ie, if it ain't  broken, fix it 'til it is  :o.

Probably best to stick with the easiest and probably the best and simplest method mentioned by Theo and others.
If you would like any info regarding measurements etc. I would be glad to help.

Martyn
www.melodeonrepairs.co.uk

Thanks, Martyn - something I may get round to at some stage. I've had the grille off just for a look, but that's as far as I've got in dismantling so far. Button travel isn't obviously causing problems yet.

On reflection, the metal bar would make sense if  it were commercially available as a part, the owner already had metal-working or casting skills or just possibly the part was originally meant for something completely different. It looked very neat and manufactured, so who knows?
Logged
D/G Pokerwork, perfectly dreadful Scholer G/D Anglo, guitars, harmonicas, etc

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Scarlatti Improvement (?)
« Reply #22 on: May 28, 2011, 11:57:07 PM »

I've seen that method used,  but in practice it's more difficult to instal successfully, the main difficulty being the rigidity of the bar. It needs to be stiff enough to give the same effect in the middle as at the ends.  The strip if wood under the levers is supported along it's whole length, so rigidity is not an issue.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Scarlatti Improvement (?)
« Reply #23 on: May 29, 2011, 10:19:46 PM »

Measuring done (I always knew that microcalliper from the bantam kit would come in useful) ! Just got to find a suitable wood strip now from my scrap box. Then - "Vazoom!" and  :||:.
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Scarlatti Improvement (?)
« Reply #24 on: June 07, 2011, 11:44:09 AM »

Pine strip in place. Plays OK but a bit short of breath again. I suspect the wood may need the attentions of a set of needle files tenderly applied. Thanks to Theo and all for advice and help.
  :-*
I've also had the "D" reed bank out to replace a valve that had come unstuck! This may not seen very adventurous to most of you, but it was to me - and I got it put back OK without major surgery.  :Ph
Now -  :||: :||: etc
« Last Edit: June 07, 2011, 10:31:17 PM by Ebor_fiddler »
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Tufty

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 855
  • Dino Bincis etc
Re: Scarlatti Improvement (?)
« Reply #25 on: June 07, 2011, 09:18:02 PM »

I've seen that method used,  but in practice it's more difficult to instal successfully, the main difficulty being the rigidity of the bar. It needs to be stiff enough to give the same effect in the middle as at the ends.  The strip if wood under the levers is supported along it's whole length, so rigidity is not an issue.
I cobbled together a similar thing with cork tile and drawing pins! It worked fine for years but had Theo do a proper job when the erica went in for a tune up.
Logged

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Scarlatti Improvement (?)
« Reply #26 on: June 15, 2011, 12:25:05 AM »

Well - I've had it out sessioning tonight and the improvements worked!  ;D It's much easier to play and I even managed to play it with the "tough guy" sngle strap. Thanks to everybody for your help and support.

Chris.
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: Scarlatti Improvement (?)
« Reply #27 on: June 15, 2011, 10:20:46 AM »

Well done you, its always a joy to find yourself at ease again after such an adventure, by the way is a " tough guy" sngle strap, a fiddler's  term  ;D AtB mory
Logged

HallelujahAl

  • Guest
Re: Scarlatti Improvement (?)
« Reply #28 on: June 15, 2011, 03:09:26 PM »

Quote
the "tough guy" sngle strap
LOL! >:E
Logged

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Scarlatti Improvement (?)
« Reply #29 on: June 16, 2011, 01:50:56 PM »

I think Al, Theo and LDT at least will all agree with me that "tough guy single strap" is not yet official fiddler jargon, though we can no doubt work on this. It is just that I have noticed that many of the younger (by chronological description) males, bent on showing heir muscular selves skills, tend to adopt this strap, stretched as long as possible, similar to the low-hanging guitars worn by contemporaries of mine (not me though, my arms aren't long enough!). I believe this fashion attracts young ladies, which is why I have never ever used it, honest missus!  :||:
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Tufty

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 855
  • Dino Bincis etc
Re: Scarlatti Improvement (?)
« Reply #30 on: June 16, 2011, 05:42:03 PM »

It is not only the wilder young element, I must confess that I have only ever used one strap, often a guitar strap! I blame these bad habits on watching "Miami Vice", which set a sartorial style which still holds sway over parts of the far north ;D
Logged

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Re: Scarlatti Improvement (?)
« Reply #31 on: June 17, 2011, 01:19:57 AM »

You're not truly rock and roll until you can swing your box around your neck
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal