Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Hohner CShop reedblocks  (Read 6117 times)

0 Members and 1 Guest are viewing this topic.

bergerland

  • Member
  • *
  • Offline Offline
  • Posts: 5
Re: Hohner CShop reedblocks
« Reply #20 on: August 14, 2014, 10:58:55 AM »

I too have an old Erica in G/C, (it really IS old, and I'm pretty sure it's German-built) along with a Pokerwork in D/G. The Erica has a beautiful tone, but is not a lot of use to me in terms of Morris dancing, which is the medium in which I usually play. I've been wondering about swapping the reed blocks over, to turn the Erica into a D/G, and decided to bite the bullet this morning. But I couldn't get the D/G reed blocks to fit into the slot on the Erica, and would have had to shave a millimetre or so off the base, which I didn't think was a good idea, so I left things as they were.

Should I have been a bit braver? Has anyone any experience of this, or any advice?

Rob

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner CShop reedblocks
« Reply #21 on: August 14, 2014, 11:30:59 AM »

Hohner two row reed blocks do have some small changes over the years.  The clamping arrangent has three main versions for example.  Also there are differences in the placing of the gasket, in some it is on the reed block and others on the base board.  The hole size and spacing has always remained the same so if you can make the adjustments to the clamp and ensure there is gasket on one surface only then any blocks can be adapted to fit.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Hohner CShop reedblocks
« Reply #22 on: August 14, 2014, 08:54:39 PM »

I've just done precisely that. My Erica had gasket on the reed block, but the Pokerwork had gasket on the fondo. Hence I put some of CGMs self adhesive gasket stuff on he Erica, and cut the holes out with a craft knife. The DG reed blocks from the Pokerwork were ever so slightly to wide, so I just faced off one of the wooden blocks that keep the reed blocks in place.

Total time, including replacing bellows gaskets and straps, was under an hour. I wish all jobs were that easy !   ;)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

bergerland

  • Member
  • *
  • Offline Offline
  • Posts: 5
Re: Hohner CShop reedblocks
« Reply #23 on: August 15, 2014, 11:48:12 AM »

Thanks for your words, Theo and Pikey. I'm encouraged to have another go. It'll give me an Erica, albeit slightly beaten up, but an Erica nonetheless...
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner CShop reedblocks
« Reply #24 on: August 15, 2014, 12:37:13 PM »

Did you get bass/chord blocks or just treble?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

reedboxman

  • Member
  • *
  • Offline Offline
  • Posts: 9
Re: Hohner CShop reedblocks
« Reply #25 on: August 19, 2014, 01:52:23 PM »

I will be getting both but from a Forum member rather than the Cshop.  May still use Cshop on another occasion...
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal