Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Brass Reeds  (Read 1956 times)

0 Members and 1 Guest are viewing this topic.

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Brass Reeds
« Reply #20 on: February 09, 2022, 02:22:11 AM »

Hi John,

I still suspect that you can get the pitches you need with a variety of brass or bronze alloys. I've seen them made from many types of brass and made them myself.

Work hardening is only part of the trick.

Another key component that influences pitch, besides the properties of the material and the length of the reedtongue, is the thickness taper of the reed. This will greatly influence the frequency of vibration. There's a lot of art to it, that you'll learn by experimentation, but as I recommended above it can help to model your reeds on a working one of similar pitch. In general, the lowest pitched reeds will be thickest at the tip, the middle pitches will have a relatively equal thickness along their length, and the highest pitched reeds will be thinner at the tip than at the foot. 

But you want to thin the reed enough that it is flexible for good volume.

PG
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Brass Reeds
« Reply #21 on: February 10, 2022, 09:13:35 AM »

Hi John,

I still suspect that you can get the pitches you need with a variety of brass or bronze alloys. I've seen them made from many types of brass and made them myself.

Work hardening is only part of the trick.

Another key component that influences pitch, besides the properties of the material and the length of the reedtongue, is the thickness taper of the reed. This will greatly influence the frequency of vibration. There's a lot of art to it, that you'll learn by experimentation, but as I recommended above it can help to model your reeds on a working one of similar pitch. In general, the lowest pitched reeds will be thickest at the tip, the middle pitches will have a relatively equal thickness along their length, and the highest pitched reeds will be thinner at the tip than at the foot. 

But you want to thin the reed enough that it is flexible for good volume.

PG

Hi Paul,   Thanks  (:)   My phosphor Bronze arrives today and I have acquired some small diameter brass rod that will suit the job so I will have a go with both.  I have also topped up on emery wheels. What I thought I would do is try thinning by peening and by taking the material down by abrasion.  As you say it will be a bit of a feel thing to get right.  Its all about where you establish the moment of area and mass as you say.

May have to get the micrometer out!

John

John   
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Brass Reeds
« Reply #22 on: February 22, 2022, 06:12:47 PM »

Hi John,

I still suspect that you can get the pitches you need with a variety of brass or bronze alloys. I've seen them made from many types of brass and made them myself.

Work hardening is only part of the trick.

Another key component that influences pitch, besides the properties of the material and the length of the reedtongue, is the thickness taper of the reed. This will greatly influence the frequency of vibration. There's a lot of art to it, that you'll learn by experimentation, but as I recommended above it can help to model your reeds on a working one of similar pitch. In general, the lowest pitched reeds will be thickest at the tip, the middle pitches will have a relatively equal thickness along their length, and the highest pitched reeds will be thinner at the tip than at the foot. 

But you want to thin the reed enough that it is flexible for good volume.

PG

Just wanted to say a big thanks for all the advice  :D  I seem to have achieved today what I thought was impossible.  I have a working reed. You are right you do need work hardened material.  You need it to stretch the yield point.  I also did an experiment and made a reed and then annealed ..... the lower yield point gives you far less leeway.

Also really good advice re the profile.  It took a while but you can really take the reed down across its length and see and feel an improved dynamic.

For this one today I used work hardened phosphor bronze strip (cold rolled PB102). I cut a blank at the max aperture width. I then took it down with a hand held rotary emery wheel (lengthwise) and files.  I concentrated on getting a high frequency profile (thick>thin). This gave me a blank working at roughly my target frequency (G# 830Hz).  I then trimmed the length and tapered the reed to suit the aperture. This raised the frequency to 1030Hz.  I then gradually took down the root thickness to lower the frequency and increase flexibility.  This brought flexibility back down the length of the reed.  If you keep twanging the reed you can see the bend profile. I found that it was a combination of reducing the reed root and down the length of the reed that improved the dynamic.  I used diamond files and then emery boards for the final tuning down to 830hz.  The emery boards were good as they ensured a smooth thickness profile down the reed length.

So ...... I want to say a big thanks to all that responded…  I now have a reed that works at 830.6 Hz ;D

I really appreciate the help and encouragement you get from this site  ....... Thank you   :||:

John

...... Two more to go  ;)

Here are some pictures:

Reed Blank - Hand filed by John Burks, on Flickr

Reed Fitted - hand filed by John Burks, on Flickr

Replacement Reed - Fitted to Aperture by John Burks, on Flickr

Reed Replacement - Reed Gap .0015” by John Burks, on Flickr

Reed Replacement - Tuned Reed by John Burks, on Flickr

Reed Replacement - Fitted by John Burks, on Flickr
 
« Last Edit: February 22, 2022, 08:45:42 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Brass Reeds
« Reply #23 on: February 22, 2022, 09:14:50 PM »

Great to hear John, thank you very much for sharing your work with us!

Paul
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Brass Reeds
« Reply #24 on: February 22, 2022, 09:23:33 PM »

Great to hear John, thank you very much for sharing your work with us!

Paul
Seconded! - Job well done and your detail description of method ( and mechanics) is invaluable to others.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Brass Reeds
« Reply #25 on: February 22, 2022, 11:12:43 PM »

Nice work.  You seem to have developed a good feel for the process of crafting a reed tongue.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal