Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: please remove  (Read 1496 times)

0 Members and 1 Guest are viewing this topic.

Elizabeth Moran

  • Either that B-word or that C-word
  • Member
  • *
  • Offline Offline
  • Posts: 42
  • Why, yes, I will have some cheese with that whine.
    • Bookface
please remove
« on: October 21, 2023, 07:29:17 PM »

please remove
« Last Edit: October 24, 2023, 12:58:21 AM by Elizabeth Moran »
Logged
C#/D Paolo Soprani/Busilacchio MMM
A/Bb Hohner Presswood MM

FS: HoHner Swiss-made Primatona D/D# with Paolo basses with F# push for Finbar Dwyer music.
FS: Paolo Soprani 21/8 LMM B/C 2-coupler, recently revalved, terrific sound.

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Difficult action on a 1930s 3-v Double Ray
« Reply #1 on: October 22, 2023, 01:51:37 AM »

Judging by the pattern of rust/oxidation marks on the arms that is visible in your photo, it would seem likely that there would be corrosion where the axle goes through the arms, and/or on the axle itself, and possibly the springs. I doubt that cleaning/lubricating in situ would achieve much, so sadly it looks like the entire mechanism needs to be removed, stripped and thoroughly cleaned. Unfortunately, in doing so, there is the danger that the action will then become sloppy due to matter being removed from the axle and from the holes in the arms during the cleaning process.
My best suggestion in the first instance might be to remove the keyboard, unhook the springs, remove the mechanism from the accordion in one piece, then gently work the axle around a few times, which *might* loosen up the rust/oxidation sufficiently to prevent binding. Reassemble and hope....Worth a try, though it may not prove to be a long term solution and you may have to revert to the full clean-up solution.

Good luck....

Edited to add that, in view of Theo's comments below, most of the above is no longer relevant. And I, too, must agree with Lars' assessment ....
« Last Edit: October 22, 2023, 01:37:09 PM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Difficult action on a 1930s 3-v Double Ray
« Reply #2 on: October 22, 2023, 02:41:16 AM »

If the springs are only 'slightly rusty' replacement is probably not necessary.  Assuming your action problem is not entirely corrosion-related, it is possible to weaken the spring tension by bending back the length of wire that is sticking up from the coil and pushing forward on the key/pallet assembly (a forum search on 'bend spring' should bring in helpful threads).
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Difficult action on a 1930s 3-v Double Ray
« Reply #3 on: October 22, 2023, 08:54:32 AM »

Before going for Malcom's approach, I would suggest trying clock oil / watch oil,  It comes in tiny bottles with a wire dipstick on the cork, the wire is used to carry a tiny drop of oil to the point of application and capillary action then draws oil into the bearing surfaces. I have many times been amazed at the effect a tiny amount of oil has on a sticking surface. I would put a drop on the coil wraps round the arbor (axle) of the mechanism and to the non- spring side of each lever. After that I would go for Tirpous suggestion....and then Malcom's.
Logged

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Difficult action on a 1930s 3-v Double Ray
« Reply #4 on: October 22, 2023, 09:06:20 AM »

These are not the same as a 2 voice Hohner, or the usual larger 3 voice Corsos. It's important to know that, and that the action geometry requires more tension to keep the pallets shut, and thus with a short arm up the button making it feel tight to play.
You can loosen the springs slightly, but not much.

I've had a handful of these, and they all needed more pressure on the button to play. Still lovely boxes, but not to be compared to a 2v in terms of button tension. That'll be comparing apples to bananas.

Not to be all "suck it up, and just play it", but if you want the pallets tight even under hard pressure on the bellows, this is how it'll feel. They're still fun to play, just fixing up one in C#/D here, and after 10 minutes I don't think too much of the tension.

Please don't use oil. The amount of dust you'll have sticking to it after a few years...
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Difficult action on a 1930s 3-v Double Ray
« Reply #5 on: October 22, 2023, 09:29:44 AM »

I think this is a box that I supplied to Elizabeth.  If it is that one I have already stripped and cleaned the axle rod and the joints.  The visible rust is on the surface only and as far as I can tell is not causing any problems or weakness.  The way springs fail is usually catastrophic not gradual.  In other words they break without much warning rather than gradually weaken.
I agree with what Lars says about oil.  Please don’t use it.  It might possibly produce a quick improvement but in the medium to long term it will result in dust gathering round the moving parts.  These mechanisms are designed to operate dry.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Difficult action on a 1930s 3-v Double Ray
« Reply #6 on: October 22, 2023, 11:54:24 AM »


Please don't use oil. The amount of dust you'll have sticking to it after a few years...

Hadn't thought of that.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Difficult action on a 1930s 3-v Double Ray
« Reply #7 on: October 22, 2023, 08:45:10 PM »

I’ve worked on accordions where it was clear someone had used oil on both the treble/bass end mechanics and even on the reed-tongues themselves. In every case it had attracted dust, grime and other undesirables. Don’t do it!

Also, everything that Lars said!
Logged
C#/D player

Elizabeth Moran

  • Either that B-word or that C-word
  • Member
  • *
  • Offline Offline
  • Posts: 42
  • Why, yes, I will have some cheese with that whine.
    • Bookface
please remove
« Reply #8 on: October 23, 2023, 08:43:21 AM »



Thank you, all!
« Last Edit: October 24, 2023, 12:59:56 AM by Elizabeth Moran »
Logged
C#/D Paolo Soprani/Busilacchio MMM
A/Bb Hohner Presswood MM

FS: HoHner Swiss-made Primatona D/D# with Paolo basses with F# push for Finbar Dwyer music.
FS: Paolo Soprani 21/8 LMM B/C 2-coupler, recently revalved, terrific sound.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal